Research and development of liquid hydrogen (LH2) temperature monitoring system for marine applications

Monitoring the temperature in liquid hydrogen (LH₂) storage tanks on ships is important for the safety of maritime navigation. In addition, accurate temperature measurement is also required for commercial transactions. Temperature and pressure define the density of liquid hydrogen, which is directly linked to trading interests. In this study, we developed and tested a liquid hydrogen temperature monitoring system that uses platinum resistance sensors with a nominal electrical resistance of approximately 1000 Ω at room temperature, PT-1000, for marine applications. The temperature measurements were carried out using a newly developed temperature monitoring system under different pressure conditions. The measured values are compared with a calibrated reference PT-1000 resistance thermometer. We confirm a measurement accuracy of ±50 mK in a pressure range of 0.1 MPa–0.5 MPa.     

Fundamental Evaluation of Power Supply and Rectifiers for Wireless Power Transfer Using Magnetic Resonant Coupling

This paper provides a fundamental analysis of a power supply and rectifiers for wireless power transfer using magnetic resonant coupling (MRC). MRC enables efficient wireless power transfer over middle‐range transfer distances. MRC for wireless power transfer should operate at a high frequency in the industry science medical band, such as 13.56 MHz, because the size of the transfer device decreases at higher transfer frequencies. Therefore, the output frequency of the power supply on the transmitting side should be 13.56 MHz. In addition, the rectifier on the receiving side is operated at a high frequency. This paper focuses on the reflected power in the power supply and rectifiers. Thus, the parametric design method is clarified for the power supply, including a low‐pass filter to match the output, the impedance of the power supply with the characteristic impedance of the transmission line. In addition, the effects on the rectifiers of silicon carbide and gallium nitride diodes are confirmed by performing an experiment and a loss analysis.     

Fracture and deformation properties of Ni-Fe superalloy in cryogenic high magnetic field environments

The present paper includes experimental and analytical data on the fracture properties of a nickel-iron superalloy, a ferromagnetic austenite, at 4 K in magnetic fields of 0 and 6 T. The tensile, notch tensile and small punch tests are employed. A finite element analysis is also performed to convert the experimentally measured load-displacement data into useful engineering information. To interpret the results we review the available theory of the influence of magnetic field on the stress intensity factor for a crack in ferromagnetic materials.     

Studies on chitin. IX. Crosslinking of water-soluble chitin and evaluation of the products as adsorbents for cupric ion

Water-soluble chitin was successfully crosslinked to varying extents with glutaraldehyde in homogeneous aqueous solutions to improve the properties as an adsorbent for metal cations, and the effects of crosslinking were discussed. Complete insolubilization was achieved with the fivefold excess aldehyde, but, in terms of adsorptivity of Cu²⁺, the chitin crosslinked at an aldehyde/amino group ratio of 1.0 was found to exhibit remarkable capacity and was much superior to others. The desorption of Cu²⁺ from the adsorption complex was also attained effectively at pH 2.0. These results indicated that the loose crosslinking was quite simple and efficient to produce high capacity adsorbents for practical use. Thermal behavior of the crosslinked chitin was examined by TMA and TGA; a softening phenomenon was observed at 145°C.     

Mechanical alloying in the Al-Bi alloy system

Mechanical alloying (MA) was carried out to investigate the MA behaviour of the immiscible Al-10, 30 at % Bi alloys. After the MA processing, the Al and Bi were finely and homogeneously alloyed. The Bi crystallite size decreased to 25 nm and 30 nm in the Al-10 at % Bi and Al-30 at % Bi alloys, respectively. By increasing the MA time, the hardness increased up to a value of 80 H _v, which is larger than that obtained from the rule of mixtures. The lattice parameter of Bi decreased by about 0.27%, which shows the formation of a non-equilibrium hcp Bi super-saturated solid solution. The extended solubility of Al in Bi was 1.9% in the Al-30 at % Bi alloy. Due to the extended solubility, depression of the melting temperature of hcp Bi was confirmed in the mechanically alloyed Al-Bi alloys. The maximum depression in the temperature was about 10 K. The measured values corresponded well with those estimated from the extrapolation of the solidus line.     

Preparation and photoconduction of rapidly quenched films in the Bi2O31bM2O5 system (M=V,Nb and Ta)

The Bi₂O₃1bM₂O₅ films (M=V, Nb and Ta) were prepared by a rapid quenching technique using a twin-roller type equipment. Quenched film of pure Bi₂O₃ partially precipitated a tetragonal phase which differs from well-known β-Bi₂O₃ in structure. In every (Bi₂O₃)_0.975 (M₂O₅)_0.025 composition (2.5% M₂O₅), the tetragonal phase was obtained as single phase, and the tetragonality became greater than that of the pure Bi₂O₃. Beyond this composition, the tetragonality decreased to form δ-phase with a fcc structure with increasing the M₂O₅ content. The lowest V₂O₅ content forming a δ-phase was 5%, while a slight tetragonality still remained in the samples containing 10% Nb₂O₅ and 10% Ta₂O₅, respectively. From the measurement of the photoconductivities of the quenched films, it was proved that a photoconduction appeared in the tetragonal phase while no photoconductivity was observed in the cubic phase. The characteristic of the photoconduction was that a remarkable decrease in the resistivity was observed when a light of ca. 500 nm in wave length was irradiated on the films.     

Recovery retardation in equal channel angular pressed Al–Zr alloy during friction stir welding

The effect of Zr on reduction of hardness and microstructure in an FS weld of equal channel angular-pressed Al alloy was investigated. Zr addition to Al suppressed dynamic recovery in the thermomechanically affected zone and enabled retention of the high hardness of the ECA-pressed material throughout the weld.     

Stress analysis with arbitrary body force by boundary element method

Linear stress analysis without body force can be easily carried out by means of the boundary element method. Some cases of linear stress analysis with body force can also be solved without the domain integral. However domain integrals are generally necessary to solve the linear stress problems with complicated body forces. This paper shows that the linear stress problems with complicated body forces can be solved approximately without the domain integral. In order to solve these problems, the domain is divided into small areas using contour lines of body force. In these areas, the distributions of body force are assumed approximately to satisfy the Laplace equation.     

Preparation and photoconduction of rapidly quenched films in the Bi2O3-TiO2 system

The rapidly quenched films in the Bi₂O₃-TiO₂ system (0 to 60% TiO₂) were prepared using a twin-roller type apparatus. The films precipitated Bi₂O₃ solid solutions of different types in the composition ranges, with TiO₂ contents of 0 to 5, 7.5 to 10 and 12.5 to 40%, respectively. The first solid solution had a tetragonal structure of -form. The second, though also crystallized in the tetragonal structure, adopted a disordered modification of the -form. The third solid solution was -form (defect fluorite structure). The formation of amorphous phase commenced in the composition with 30% TiO₂, and the films became completely amorphous beyond 50% TiO₂. The quenched films showed a certain instability to decompose or transform into the different phase assemblage by annealing at higher temperatures (about 400 to 500° C, except 260° C for the pure Bi₂O₃ film). The quenched films were also characterized by a high photoconductivity. The photoconduction mechanism was suggested to be associated with a structural imperfection of Bi₂O₃ accompanied by a certain amount of pentavalent bismuth ion.