Overlapping tracks processed by TIG melting TiC preplaced powder on low alloy steel surfaces

An overlapping composite track coating was produced on a steel surface by preplacing a 0·5 mm thick layer of TiC powder and then melting using a tungsten inert gas torch of constant energy input. The influence of the overlapping operation on preheating of the substrate, the dissolution of TiC particulates and the subsequent depth and hardness of the composite layer was analysed. The melt microstructure consisted of both undissolved and partially dissolved TiC particulates, together with a variety of morphologies and sizes of TiC particles precipitated during solidification. Preheating, resulting from the overlapping operation, occurred, producing additional melting of the TiC particulates and deeper melt depths but with a reduced volume fraction of TiC precipitates in the subsequent tracks. A maximum hardness of over 800 HV was developed in the composite layer. The high hardness was unevenly distributed in tracks melted at the initial and final stages, while it varied across the melt depths in other tracks.     

Direct comparison of Eulerian–Eulerian and Eulerian–Lagrangian simulations for particle-laden vertical channel flow

Particle-laden flows in a vertical channel were simulated using an Eulerian–Eulerian, Anisotropic Gaussian (EE-AG) model. Two sets of cases varying the overall mass loading were done using particle sizes corresponding to either a large or small Stokes number. Primary and turbulent statistics were extracted from these results and compared with counterparts collected from Eulerian–Lagrangian (EL) simulations. The statistics collected from the small Stokes number particle cases correspond well between the two models, with the EE-AG model replicating the transition observed using the EL model from shear-induced turbulence to relaminarization to cluster-induced turbulence as the mass loading increased. The EE-AG model was able to capture the behavior of the EL simulations only at the largest particle concentrations using the large Stokes particles. This is due to the limitations involved with employing a particle-phase Eulerian model (as opposed to a Lagrangian representation) for a spatially intermittent system that has a low particle number concentration.     

Survey of acceptor dopants in SrTiO3: Factors limiting room temperature hole concentration

Unintentional impurities often found in strontium titanate (doped or undoped) have hindered efforts to study individual impurities experimentally. To fill this gap, a computational survey of acceptor-type point defects of common intentional or unintentional impurities (Al, Cu, Fe, K, Mg, Mn, N, Na, Ni, and Zn) is presented. Utilizing defect formation energies from density functional theory using hybrid exchange correlation functionals in a grand canonical model of the defect chemistry, the equilibrium Fermi level (μ_e) was calculated as a function of processing conditions for pure SrTiO₃, SrTiO₃ individually doped with each impurity, and SrTiO₃ co-doped with Al and N. Above a certain concentration, each impurity reduced the maximum predicted hole concentration relative to the intrinsic case. Al, Mg, Zn, K, and Na exhibited similar trends and behaved more like ideal acceptors while N, Ni, Fe, Mn, and Cu were all unique and pinned μ_e near or above the mid-gap in most conditions. Al/N:SrTiO₃ also exhibited similar trends at 800°C for all Al/N ratios, but more variation at 25°C. Additionally, the behavior of Al:SrTiO₃ was not recovered until Al/N = 10⁴. This suggests that to achieve SrTiO₃ with free holes at room temperature, the concentration of most impurities must be controlled.     

Development and evaluation of sub-element testing of SiC/SiC ceramic matrix composites at elevated temperatures

SiC/SiC ceramic matrix composites (CMCs) are being developed for use in aero-engines to replace nickel superalloy components. Sub-element testing acts as the key stepping stone in bridging understanding derived from basic coupon testing and more complex component testing. This study presents the development of high temperature C-shape sub-element testing with the use of digital image correlation to study damage progression. The specimen is designed with a bias towards a mixed mode-stress state more similar to what a CMC component may see in service. Both monotonic and fatigue tests were completed on C specimens and compared with predicted behaviour from modelling. Test data from both test types suggested that specimens were failing once they reached a critical radial stress level. However evidence from fractography of specimens showed that in both monotonic and fatigue tests radial cracks (driven by hoop stresses) are initiating prior to circumferential cracks.     

Advancing responses to climate change through improved interplay between planning theory and practice

ABSTRACT

Many planning agencies worldwide now see climate change response as unavoidable. This paper proposes that a central task for contemporary planning theory is to guide planning practice as it develops multi-dimensional responses. We examine three theoretical constructs: anticipatory governance, legitimacy and social-ecological resilience. We argue that each conceptualises challenges climate change presents to planning practice, while providing theoretically informed options for responses. Building on this, we utilize Friedmann’s [2008. “The Uses of Planning Theory: A Bibliographic Essay.” Journal of Planning Education and Research 28 (2): 247–257. doi:10.1177/0739456X08325220] tasks for planning theory as a framework to assess the utility of planning theories to guide climate change response through practice. Associated issues are discussed, including the influence of translatable planning theories and the value of importing knowledge from other disciplines. The paper concludes that more sophisticated interplay between planning theory and practice may improve planning responses to the climate change threat. The need for planning theory to translate its conceptual discoveries to the domain of practice is key.