Opening-up Status of China＇s Oil ＆ Gas Market

Since the founding of P.R.China,Particularly after the lauch of reform and opening up in 1978,China＇s oil and gas industry has undergone a series of significant reforms and restructuring.it has set up a complete oil and gas industry system.     

Microscale Patterning of Mesoscopic PZN-PT Single Crystal Films by Crystal ion Slicing and Laser-Induced Etching

Advances in the fabrication of solid-solution single crystal relaxor ferroelectrics have made it possible to produce highly efficient piezoelectric crystals, and have attracted renewed interest in the use of these crystals for a new generation of piezoelectric transducers, actuators and sensors. Of particular interest is their incorporation into micro-electromechanical systems (MEMS). In this paper we report on the laser-induced wet chemical etching of lead zinc niobate-lead titanate (PZN-PT) in hydrochloric acid (HCl). Argon-ion laser radiation at power levels up to 4 W is focused to a spot diameter of about 15μm and results in the chemical etching of grooves at patterning speeds up to 5μm/sec. Crystal ion slicing, an ion-implant-based film separation technique, is used in combination with laser etching to form 5 to 10μm-thick patterned and freestanding films for incorporation into micro-electromechanical devices.     

Bandpass filters with reconfigurable transmission zeros using varactor-tuned tapped stubs

In this letter, bandpass filters with one or two tunable transmission zeros are proposed. The reconfigurable transmission zeros are implemented through varactors in combination with tapped quarter-wavelength stubs. Based on mixed mode simulations including EM simulation and circuit simulation, the proposed filters were designed and fabricated on low-cost FR4 board. The measurement results verified the design concepts.     

新型实用布线算法──L─M算法

本文提出新型布线算法，集李氏迷宫法与线搜索法的长处为一体，以饱和带法进行动态排序，以线搜索法确定借孔位置，然后用李氏法进行单层布线，获得最佳路径，从而达到线型好，布通率高的效果。     

Deformation and fracture of glass bead/ CTBN-rubber/epoxy composites

Carboxyl-terminated butadiene-acrylonitrile-rubber decreases modulus and yield stress of the studied epoxy but increases fracture toughness. The addition of glass bead compensates for the loss in modulus but has little effect on yield stress. However, it significantly contributes to the fracture toughness by providing additional mechanisms for toughening of both the unmodified and rubber-modified epoxy. For the toughened epoxies studied, fracture surfaces gave only limited information on fracture mechanisms since significant energy absorption also occurs in the material below the fracture surface. Suggestions for suitable material compositions for fiber composite matrices are given.     

Systematic characterization of Cl2 reactive ion etchingfor improved ohmics in AlGaN/GaN HEMTs

Pre-metal-deposition reactive ion etching (RIE) was performed on an Al_0.3Ga_0.7N/AlN/GaN heterostructure in order to improve the metal-to-semiconductor contact resistance. An optimum AlGaN thickness for minimizing contact resistance was determined. An initial decrease in contact resistance with etching time was explained in terms of removal of an oxide surface layer and/or by an increase in tunnelling current with the decrease of the AlGaN thickness. The presence of a dissimilar surface layer was confirmed by an initial nonuniform etch depth rate. An increase in contact resistance for deeper etches was experienced. The increase was related to depletion of the two-dimensional (2-D) electron gas (2-DEG) under the ohmics. Etch depths were measured by atomic force microscopy (AFM). The contact resistance decreased from about 0.45 Ωmm for unetched ohmics to a minimum of 0.27 Ωmm for 70 Å etched ohmics. The initial thickness of the AlGaN layer was 250 Å. The decrease in contact resistance, without excessive complications on device processing, supports RIE etching as a viable solution to improve ohmic contact resistance in AlGaN/GaN HEMTs     

A concise process technology for 3-D suspended radio frequency micro-inductors on silicon substrate

In this letter, a concise process technology is proposed for the first time to enable the fabrication of good quality three-dimensional (3-D) suspended radio frequency (RF) micro-inductors on bulk silicon, without utilizing the lithography process on sidewall and trench-bottom patterning. Samples were fabricated to demonstrate the applicability of the proposed process technology.     

Direct adaptive control of nonminimum phase systems using integralaction

A direct adaptive control scheme is proposed for nonminimum-phase systems in which controller parameters are estimated from the recursive least-squares algorithm and additional auxiliary parameters are obtained from the proposed polynomial identity. A local convergence is guaranteed without any extra condition. Integral action is incorporated into the adaptive controller to eliminate the steady-state error and to satisfy a condition of the unique solution for the polynomial identity. The control law used in this scheme is based on the set-point-on-I-only proportional-integral-derivative (PID) structure