Depassivation and repassivation of stainless steels by stepwise pH change

Immersion tests with different stainless steels have been performed, while the pH was stepwise decreased and then increased again. During 8.5-day exposure, the depassivation and repassivation pH values as a function of pitting resistance equivalent number were determined. There is always a gap between both pH values (depassivation and repassivation), indicating that for every steel, there are conditions where an existing passive layer can be maintained but cannot be rebuilt after depassivation. In such environments, the passive layer is thicker, consisting mainly of molybdenum and iron rich oxides, while chromium is dissolved. Usually, depending on conditions, the passive layer is more chromium-rich, especially the inner layer. This is relevant, for example, for acidizing jobs in oil and gas industry, proving that repassivation after acidizing will happen promptly, when the pH is increased again.     

Bonded aerospace repairs under tensile loading: Wet chemical surface treatment and selected environmental conditions

Repair of composite structures and the impact of demanding environmental conditions is a crucial issue for the aircraft industry because of the increasing use of composites in modern aircraft. Consequently, the impact of environmental conditions common for aircraft applications on repair specimens in comparison to nonrepaired specimens is studied. All specimens are produced from a woven carbon fiber-reinforced epoxy-based prepreg. For the repair-specimens, an epoxy-based film adhesive is used for the soft patch repair approach. During the repair process, the surface of the precured prepreg is prepared by a mechanical method (sanding) and an additional chemical functionalization, respectively. Moisture absorption of the repair specimens is independent of the surface preparation method and higher for the repaired than for the nonrepaired specimens. The key influencing environmental conditions for the tensile strength and the failure mode of the repair specimens are elevated temperature testing as well as hot/wet conditioning and conditioning in deionized water. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47506.     

A Flexi-PEGDA Upconversion Implant for Wireless Brain Photodynamic Therapy

Near-infrared (NIR) activatable upconversion nanoparticles (UCNPs) enable wireless-based phototherapies by converting deep-tissue-penetrating NIR to visible light. UCNPs are therefore ideal as wireless transducers for photodynamic therapy (PDT) of deep-sited tumors. However, the retention of unsequestered UCNPs in tissue with minimal options for removal limits their clinical translation. To address this shortcoming, biocompatible UCNPs implants are developed to deliver upconversion photonic properties in a flexible, optical guide design. To enhance its translatability, the UCNPs implant is constructed with an FDA-approved poly(ethylene glycol) diacrylate (PEGDA) core clad with fluorinated ethylene propylene (FEP). The emission spectrum of the UCNPs implant can be tuned to overlap with the absorption spectra of the clinically relevant photosensitizer, 5-aminolevulinic acid (5-ALA). The UCNPs implant can wirelessly transmit upconverted visible light till 8 cm in length and in a bendable manner even when implanted underneath the skin or scalp. With this system, it is demonstrated that NIR-based chronic PDT is achievable in an untethered and noninvasive manner in a mouse xenograft glioblastoma multiforme (GBM) model. It is postulated that such encapsulated UCNPs implants represent a translational shift for wireless deep-tissue phototherapy by enabling sequestration of UCNPs without compromising wireless deep-tissue light delivery.     

The effect of microstructure on hydrogen permeability of high strength steels

Hydrogen diffusivity and trapping have been studied in two advanced high strength steel grades and model samples using electrochemical permeation test. Microstructures of CP1000 and DP1000 steels consist of ferrite, martensite and a small fraction of retained austenite. In addition, bainite is present in CP1000. Model phases with predominance of a particular phase have been prepared by specific heat treatment. DP1000 has shown the lowest diffusivity among all materials, while ferritic model sample has shown the highest. Differences in hydrogen diffusion coefficient values are linked to trapping microstructural characteristics and grain size.     

Frequency domain analysis of the mirror-modified filtered-x least mean squares algorithm with low ambient noise

The mirror-modified filtered-x least mean squares (MMFxLMS ) algorithm is a variation of the FxLMS algorithm with online secondary path modeling that cannot diverge due to secondary path modeling errors. However, problems may occur when the ambient noise is not limited due to insufficient modeling power. This work shows that under a frequency domain analysis without ambient noise, the MMFxLMS algorithm is always stable, and expressions for the maximum residual noise level at any given time are obtained. It is also shown that, under the same context, convergence to the minimum residual noise is guaranteed. Still, convergence can be much slower for high secondary path modeling errors than that of the LMS or MFxLMS algorithms. Simulations confirm these results.     

Nature and etiology of hollow-organ abdominal injuries in frontal crashes

Injuries to the hollow organs of the lower digestive system carry substantial risk of complication due to infection and blood loss, and commonly require invasive abdominal surgery to diagnose and treat. The causes of, and risk factors for, lower abdomen injury in automobile collisions are poorly understood. The goal of this study was to investigate the risk factors and potential mechanisms of hollow-organ, lower abdomen injury in belted automobile occupants in frontal collisions.     

Machine learning in continuous casting of steel: a state-of-the-art survey

Journal of Intelligent Manufacturing - Continuous casting is the most important route for the production of steel today. Due to the physical, mechanical, and chemical components involved in the...     

Cometabolism of trihalomethanes by mixed culture nitrifiers

Three mixed-culture nitrifier sources degraded low concentrations (25-450 microg/L) of four trihalomethanes (THMs) (trichloromethane (TCM) or chloroform, bromodichloromethane (BDCM), dibromochloromethane (DBCM), tribromomethane (TBM) or bromoform) commonly found in treated drinking water. Individual THM rate constants (k1THM) increased with increasing THM bromine-substitution with TBM>DBCM>BDCM>TCM and were comparable to previous studies with the pure culture nitrifier, Nitrosomonas europaea. A decrease in temperature resulted in a decrease in both ammonia and THM degradation rates with ammonia rates affected to a greater extent than THM degradation rates. The significant effect of temperature indicates that seasonal variations in water temperature should be a consideration for technology implementation. Product toxicity, measured by transformation capacity (T(c)), was similar to that observed with N. europaea. Because both rate constants and product toxicities increase with increasing THM bromine-substitution, a water's THM speciation is an important consideration for process implementation during drinking water treatment. Even though a given water is kinetically favored, the resulting THM product toxicity may not allow stable treatment process performance.     

Use and Mis-Use of Measurement Scales in City Planning

By developing measurement scales the city planner can promote his long-run interest in integrating urban knowledge and his short-run interest in making valid analyses of specific problems. But the construction of measurement scales is not a random process and must be conducted according to logical rules. Inadequacies in current city planning scales are largely attributable to the lack of adherence to these rules. Housing quality scales, the most common measurement device in city planning, reveal some of the difficulties that lead to deficiencies in our measurement. The outlook is far from gloomy. Experience from other fields in index number construction, the use of scalograms, and factor analysis can Open up many promising avenues for city planning measurement.