采用温控和碘吸收池技术的发射激光稳频技术

多普勒测风激光雷达通过分析系统回波信号的多普勒频移反演出风速，为提高风场探测精度，从稳频技术方面展开研究。在稳频过程中，分别采取措施消除激光频率的长期漂移和短期抖动。针对激光频率的长期漂移，设计并研制了种子激光器温控箱，通过水浴的控温方式大大减小了激光频率的长期漂移，将激光频率稳定在±50 MHz以内；针对激光频率的短期抖动，采用以碘分子吸收池为核心器件的稳频系统，通过半导体控温方式对碘分子吸收池精确控温，控温精度达0.03 ℃，提高了稳频精度，将激光频率进一步稳定在±8 MHz以内，满足±10 MHz以内的设计精度要求。通过搭建多普勒测风激光雷达系统，对发射激光稳频装置进行系统验证，连续4组风场观测结果表明:系统探测高度为17 km，绝大部分方差在4 m/s以下，满足测风激光雷达测量指标的要求。     

Changes in the content and antioxidative activity of β-carotene and its metabolite vitamin A during gastrointestinal digestion and absorption and optimisation of HPLC-based detection

The β-Carotene (BC), an important precursor of vitamin A (VA), possesses antioxidant activity but is fat-soluble and has low bioavailability. In previous in-vitro assays evaluating antioxidant and 2,2′-azobis(2-amidinopropane) dihydrochloride (AAPH) free radical scavenging, both BC and VA showed a strong ability to scavenge radicals and protected cells from oxidative stress. Here, we used artificially simulated gastrointestinal digestion and Caco-2 cell absorption models to evaluate the bioavailability of the BC during gastrointestinal digestion and absorption using high-performance liquid chromatography (HPLC) analysis. We observed high absorptive and transfer rates of BC and detected retinol metabolites (Vitamin A). Therefore, BC can be detected in the acidic gastrointestinal environment using HPLC. Optimised method provided better separation of BC and VA in the column, improving the accuracy of the test results.     

Effect of MoS2/PTFE coatings on performance of Si3N4/TiC ceramics in dry sliding against WC/Co

To enhance the tribological performance of Si₃N₄/TiC ceramics, MoS₂/PTFE composite coatings were deposited on the ceramic substrate through spraying method. The micrographs and basic properties of the MoS₂/PTFE coated samples were investigated. Dry sliding friction experiments against WC/Co ball were performed with the coated ceramics and traditional ones. These results showed that the composite coatings could significantly reduce the friction coefficient of ceramics, and protect the substrate from adhesion wear. The primary tribological mechanisms of the coated ceramics were abrasive wear, coating spalling and delamination, and the tribological property was transited from slight wear to serious wear with the increase of load because of the lower surface hardness and shear strength. The possible mechanisms for the effects of MoS₂/PTFE composite coatings on the friction performance of ceramics were discussed.     

Transient Simulation of Hollow‐Fiber Membrane Filtration with Nonuniform Permeability Distribution

Transient simulation of filtration in hollow‐fiber membranes with nonuniform permeability distribution was conducted. The diversity of permeability distributions caused different initial flux and transmembrane pressure distributions. Manipulating the permeability distribution enables a hollow‐fiber membrane to achieve its maximum volumetric flow rate. During solid‐liquid separation, the inter‐adjustment between flux and cake distributions improved their uniformities simultaneously. The reciprocal of the volumetric flow rate of the membranes all increased linearly with water production. Severely nonuniform permeability distribution caused low water production. The numerical results could be applicable to account for the non‐ideal performance of industrial hollow‐fiber membrane modules.     

钢化玻璃白雾成因及解决方法

采用显微镜分析钢化白雾缺陷发现,钢化白雾是玻璃表面形成的凹坑,凹坑数量和大小不能量化白雾,且钢化白雾的表面形貌与进炉方向无关.针对白雾缺陷进行详细分析,给出具体的解决方法.     

Electrostatic-lenses position-sensitive TOF MCP detector for beam diagnostics and new scheme for mass measurements at HIAF

A foil–microchannel plate(MCP) detector,which uses electrostatic lenses and possesses both good position and timing resolutions, has been designed and simulated for beam diagnostics and mass measurements at the next-generation heavy-ion-beam facility HIAF in China. Characterized by low energy loss and good performances of timing and position measurements, it would be located at focal planes in fragment separator HFRS for position monitoring, beam turning, Bρ measurement, and trajectory reconstruction. Moreover, it will benefit the building-up of a magnetic-rigidity–energy-loss–time-offlight(Bρ-△E-TOF) method at HFRS for high-precision in-flight particle identification of radioactive isotope beams on an event-by-event basis. Most importantly, the detector can be utilized for in-ring TOF and position measurements,beam-line TOF measurements at two achromatic foci, and position measurements at a dispersive focus of HFRS, thus making it possible to use two complementary mass measurement methods [isochronous mass spectrometry at the storage ring SRing and magnetic-rigidity–time-of-flight(Bρ-TOF) at the beam-line HFRS] in one single experimental run.     

Development of microbially influenced corrosion on carbon steel in a simulated water injection system

Microbially influenced corrosion (MIC) on internal pipeline surfaces has become a severe problem during the water injection process in secondary oil recovery. The formation of a biofilm, normally dominated by sulfate‐reducing bacteria (SRB), is believed to be the critical step of the MIC process. A continuously fed biofilm simulating the water injection process was operated to investigate the influence of biofilm development on MIC behavior in the early phase of corrosion development. The development of the corrosion product film and biofilm was monitored for 5 months with electrochemical impedance spectroscopy, linear polarization resistance, scanning electron microscopy, 3D optical profiling, and direct weight measurement. MIC development was found to comprise three phases: initialization, transition, and stabilization. The initialization phase involved the formation of the corrosion product layer and the initial attachment of the sessile microbes on metal surface. In the transition phase, the MIC process gradually shifted from charge‐transfer‐controlled reaction to diffusion‐controlled reaction. The stabilization phase featured mature and compact biofilm on the metal surface, and the general corrosion rate (CR) decreased due to the diffusional effect, while the pitting CR was enhanced at a lower carbon source level, which supported the mechanism of direct electron uptake from the metal surface by SRB.     

热仿真技术在加固显示器热设计中的应用

根据某型加固显示器的应用环境及内部功能模块的热特性,选择强迫风冷的散热方式,并通过热仿真计算指导风扇选型,根据仿真结果验证散热方案的可行性。最终,依据试验结果验证仿真结果的准确性,为加固显示器的热设计提供思路。     

Gelation properties of goose liver protein recovered by isoelectric solubilisation/precipitation process

Isoelectric solubilisation/precipitation (ISP) process was applied to goose liver (GL) for protein extraction. The gelation properties of proteins extracted by acid processes (ACP, pH 2.0, 2.5 and 3.0) and alkaline processes (ALP, pH 11.0, 11.5 and 12.0) were estimated, where the unextracted ground GL was set as the control. Nearly 58.39~79.00% of GL proteins were recovered by ISP treatments. High molecular weight (100~250 kDa) proteins were found to be partially hydrolysed by ACP, while few changes in proteins occurred during ALP. As evidenced by rheological and textural measurements, ALP proteins formed gels with high elasticity and superior texture, whereas ACP proteins had inferior gelation properties. Moreover, ALP proteins were able to form a highly interconnected and homogeneous three‐dimensional microstructure. Predominantly, gels produced by 11.0 had optimal texture and the lowest cooking loss (P < 0.05). These results suggested that the ISP process (ALP) is a potential method to improve the economic value of GL.