Spectrophotometric investigation of the copolymerization of styrene or methyl methacrylate with 1,8‐naphthalimide dyes

The copolymerization of styrene or methyl methacrylate with 1,8‐naphthalimide dyes to yield fluorescent side‐group copolymers was investigated. During copolymerization, no changes occurred in the chromophoric systems of the dyes. Colorimetrically, it was found that more that 0.90% of the dyes were chemically bonded to the polymer chain. The effect of polymer coloration was proven by appropriate coloristic characterization. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2463–2470, 2001     

Antibacterial and antifungal activities of selected microalgae and cyanobacteria

In vitro activity of nine cyanobacterial and ten microalgal newly isolated or culture collection strains against eight significant food‐borne pathogens has been evaluated and compared. Water extracts and culture liquids of Gloeocapsa sp. and Synechocystis sp. demonstrated the widest spectrum of activity with minimal inhibitory concentration (MIC) ranging from 1.56 to 12.5 mg mL^?1. Culture liquid of Anabaena sp. had the highest activity (MIC = 0.39 mg mL^?1) but only to Gram‐positive bacteria. Ethanol extracts and fatty acids from all cyanobacteria and microalgae were active against Streptococcus pyogenes and/or Staphylococcus aureus. The fatty acids of Synechocystis sp. inhibited the growth of Bacillus cereus, Escherichia coli and Candida albicans (MIC values of 2.5–1.25 mg mL^?1, respectively). Exopolysaccharides (EPS) of Gloeocapsa sp. were the sample that exhibited activity against all test pathogens with lowest MIC values (0.125–1 mg mL^?1). High activity with a narrower range of susceptible targets demonstrated the exopolysaccharides of Synechocystis sp. and Rhodella reticulata. Antimicrobial activity was proven for phycobiliproteins isolated from Synechocystis sp., Arthrospira fusiformis, Porphyridium aerugineum and Porphyridium cruentum, respectively. In conclusion Gloeocapsa sp. and Synechocystis sp. and especially their exopolysaccharides showed the most promising potential against the examined food pathogens.     

Mechanism of anodic oxidation of molybdenum in nearly-neutral electrolytes studied by electrochemical impedance spectroscopy and X-ray photoelectron spectroscopy

Anodic oxidation of molybdenum in weakly acidic, nearly neutral and weakly alkaline electrolytes was studied by voltammetric and electrochemical impedance spectroscopic measurements in a wide potential and pH range. Current vs. potential curves were found to exhibit two pseudo-Tafel regions suggesting two parallel pathways of the dissolution process. Electrochemical impedance spectra indicated the presence of at least two reaction intermediates. X-ray photoelectron spectroscopic (XPS) results pointed to the formation of an oxide containing Mo(IV), Mo(V) and Mo(VI), the exact ratio between different valence states depending on potential and pH of the solution. A physico-chemical model of the processes is proposed and a set of kinetic equations for the steady-state current vs. potential curve and the impedance response are derived. The model is found to reproduce quantitatively the current vs. potential curves and impedance spectra at a range of potentials and pH and to agree qualitatively with the XPS results. Subject to further improvement, the model could serve as a starting point for the optimization of the electrochemical fabrication of functional molybdenum oxide coatings.     

催化逆流反应器(CH4MIN)技术及其在中国的应用潜力

通过一系列的试验，加拿大矿物与能源技术中心开发出了一项专门处理和利用煤矿矿井乏风中甲烷(甲烷体积浓度0．1％～1．0％)的技术——催化逆流反应器(CH4MIN)技术。CH4MIN技术是在催化剂的作用下，促使乏风混合气体的温度升高到足以让甲烷发生氧化，从而产生热量。通过利用这种热量达到利用乏风中甲烷的目的。本文从CH4MIN技术工作原理、试验结果分析、经济可行性分析及在中国的应用前景作了分析和论述。     

Estimation of the parameters of oxide film growth on nickel-based alloys in high-temperature water electrolytes

The Mixed-Conduction Model (MCM) has been adapted to obtain the main kinetic and transport parameters for passive film growth on nickel-based alloys in high-temperature electrolytes. For the purpose, a procedure for the calculation of these parameters from electrochemical impedance spectroscopic data measured on Ni-15% and Ni-20%Cr alloys in 0.1 M Na₂B₄O₇ at 300 °C in a wide potential range has been devised. The obtained sets of parameters have been used to successfully predict the steady-state current density versus potential dependence for the two Ni-Cr alloys, as well as the thickness versus time dependence for films grown on Alloy 600 at times ranging between a few minutes and a few thousand hours. The calculations are supported by results of previous XPS measurements of film growth on Alloy 600 showing that the barrier layer growing in the early stage consists of Cr₂O₃.     

Electrochemical behaviour of the antimony electrode in sulphuric acid solutions—II. Formation and properties of the primary anodic layer

The formation of an anodic layer during the oxidation of antimony in sulphuric acid solutions as well as the structure and properties of the layer have been studied using linear sweep voltammetry, potentiostatic oxidation, ac impedance measurements, X-ray diffraction analysis and scanning electron microscopy. The electrochemical investigations as well as the shape of the impedance spectra during electrode passivation indicate that the surface layer probably has a complicated structure. Under the conditions of these experiments the passivating film is mainly amorphous, gel-like, exhibiting good ionic conductivity and a relatively high dissolution rate. Assuming that the anodic layer consists mainly of antimony hydroxide a reaction scheme for the growth and dissolution of this film is presented.     

High-resolution subunit detection of glutamate receptor by ultrasmall gold nanoparticles

In this study, we aimed to increase the sensitivity of protein labeling using 1.4 nm gold nanoparticles and glutamate δ2 receptor (GluD2) from the postsynaptic membrane of the Purkinje cells. The very small marker size of the particles reduces the steric hindrance between antibodies leading to a higher labeling efficiency of more than one subunit per single receptor molecule. The nanoparticles are visible in 200 kV dark‐field scanning transmission electron microscope on freeze‐fractured carbon replica of nervous tissue after plasma cleaning treatment. The different elemental composition of nanoparticles as Au nanogold or CdS quantum dot can be distinguished by energy dispersive X‐ray spectroscopy. This method ensures detection of an average of three subunits per GluD2 and often labels all four of them with 1.4 nm Au nanoparticles. It is concluded that this high‐resolution microscopic method is useful for exploring the quaternary structure of membrane proteins. Microsc. Res. Tech. 75:1159–1164, 2012. © 2012 Wiley Periodicals, Inc.     

Reactive Compatibilizer Precursors for LDPE/PA6 Blends, 4

Summary: The effectiveness of some thermoplastic elastomers grafted with maleic anhydride (MA) or with glycidyl methacrylate (GMA) as compatibilizer precursors (CPs) for blends of low density polyethylene (LDPE) with polyamide‐6 (PA) has been studied. The CPs were produced by grafting different amounts of MA or GMA onto a styrene‐block‐(ethylene‐co‐1‐butene)‐block‐styrene copolymer (SEBS) (KRATON G 1652), either in the melt or in solution. A commercially available SEBS‐g‐MA copolymer with 1.7 wt.‐% MA (KRATON FG 1901X) was also used. The effect of the MA concentration and of other characteristics of the SEBS‐g‐MA CPs was also studied. The specific interactions between the CPs and the blends components were investigated through characterizations of the binary LDPE/CP and PA/CP blends, in the whole composition range. It was demonstrated that the SEBS‐g‐GMA copolymers display poor compatibilizing effectiveness due to cross‐linking resulting from reactions of the epoxy rings of these CPs with both the amine and the carboxyl end groups of PA. On the contrary, the compatibilizing efficiency of the MA‐grafted elastomers, as revealed by the thermal properties and the morphology of the compatibilized blends, was shown to be excellent. The results of this study confirm that the anhydride functional groups possess considerably higher efficiency, for the reactive compatibilization of LDPE/PA blends, than those of the ethylene‐acrylic acid and ethylene‐glycidyl methacrylate copolymers investigated in previous works.

SEM micrograph of the 75/25 LD08/PA blend (with 2 phr SEBSMA1).     

Distributed non-negative matrix factorization with determination of the number of latent features

The Journal of Supercomputing - The holistic analysis and understanding of the latent (that is, not directly observable) variables and patterns buried in large datasets is crucial for data-driven...