Fabrication of Ti3SiC2-based pastes for screen printing on paper-derived Al2O3 substrates

This paper describes the development and fabrication of pastes suitable for screen printing process using Ti₃SiC₂ as the ceramic filler and ethyl cellulose as the binder. With the aim of obtaining high quality screen printed films, the influence of different amounts of Ti₃SiC₂ filler (20–40?vol%) and binder (0–5?vol%) on the rheological properties of the pastes was investigated. Samples with higher viscosity, such as pastes containing 30?vol% and 40?vol% Ti₃SiC₂ filler, regardless of the amount of ethyl cellulose, showed a higher printing quality compared to the samples with other compositions. The different paste compositions were screen printed onto paper-derived Al₂O₃ substrates containing 28.6 ± 4.8% open porosity and sintered for 1?h under an argon atmosphere at 1600?°C. X-ray diffraction (XRD) measurements and scanning electron microscopy (SEM) analysis showed that the sintered films contained TiC as a primary phase and Ti₃SiC₂ as a secondary phase. The partial decomposition of Ti₃SiC₂ after sintering can be attributed to residual carbon from the organic additives, which decreases the thermal stability of this material.     

SiC ceramic micropatterns from polycarbosilanes

Micropatterned SiC ceramics were fabricated from polycarbosilanes applying a softlithographic replication technique. A polydimethylsiloxane mould replicated from a photolithographic microstructured silicon wafer was used as master structure. The polydimethylsiloxane mould was coated with a solution containing a mixture of two different polycarbosilanes in n-octane. After treatment at 200–400 °C the cross-linked polycarbosilane films were debonded and pyrolysed at 900 °C in nitrogen and subsequently crystallised at temperatures up to 1500 °C in argon. The cross-linking and thermal degradation behaviour of the polycarbosilanes was investigated by Fourier-transform infrared spectroscopy, differential scanning calorimetry and thermogravimetric analysis. X-ray diffractrometry showed the expected development of a nanocrystalline β-SiC (3 nm) as the main phase with increasing temperature. However, traces of α-SiO₂ derived from the polycarbosilane precursors were also detected by X-ray analysis. Removal of the α-SiO₂ dioxide with hydrofluoric acid in the pyrolysed samples and subsequent increased the crystallite size to 7 nm. The Young's modulus determined by nanoindentation was increased from 3 GPa after cross-linking to 110 GPa after crystallisation. Scanning electron microscopy revealed, that the initial micropatterns were fully retained in the pyrolysed and crystallised SiC ceramics. The micropatterned cross-linked and crystallised β-SiC based substrates exhibited light scattering characteristics, which qualify them as promising candidates for diffractive optical elements in microoptical applications.     

Paper‐Derived Bioactive Glass Tape

Porous bioactive glass (BaG) structures were manufactured applying novel preceramic paper process. Preceramic papers were produced for aqueous suspensions loaded with different contents of pulp fiber and BaG filler. Pressure loading was applied in order to increase the packing density in the paper sheets. The paper sheets were sintered at 630 °C for 1 h. The porous glass–ceramic specimens were characterized for density, porosity, composition, microstructure, and mechanical properties. A pronounced volumetric shrinkage was observed, but no surface flaws or inhomogeneous areas were detected. The mechanical strength using the ball on three balls test and elastic modulus of sintered specimens vary between 21 and 33 MPa and 0.30–0.85 GPa, respectively.     

Colloidal Processing of Glass–Ceramics for Laminated Object Manufacturing

Green tapes of Li₂O–ZrO₂–SiO₂–Al₂O₃ (LZSA) parent glass were produced by aqueous tape casting as the starting material for the laminated object manufacturing (LOM) process. The rheological behavior of the powder suspensions in aqueous media, as well as the mechanical properties of the cast tapes, was evaluated. According to ξ potential measurements, the LZSA glass powder particles showed acid surface characteristics and an IEP of around 4 when in aqueous media. The critical volume fraction of solids was about 72 wt% (27 vol%), which hindered the processability of more concentrated slurries. The glass particles also showed an anisometric profile, which contributed to an increase in the interactions between particles during flow. Therefore, the suspensions could not be processed at high solids loadings. Aqueous-based glass suspensions were also characterized by shear thickening after the addition of dispersants. Three slurry compositions were formulated, suitable green tapes were cast, and tapes were successfully laminated by LOM to a gear wheel geometry. A higher tensile strength of the green tapes corresponded to a higher tensile strength of the laminates. Thermal treatment was then applied to the laminates: pyrolysis at 525°C, sintering at 700°C for 1 h, and crystallization at 850°C for 30 min. A 20% volumetric shrinkage was observed, but no surface flaws or inhomogeneous areas were detected. The sintered part maintained the curved edges and internal profile after heat treatment.     

Introduction

International Journal of Computer Vision -     

Suppression of plant parasitic nematodes in the chinampa agricultural soils

Soil from the chinampa agricultural system in the Valley of Mexico suppressed damage by plant-parasitic nematodes to tomatoes and beans in greenhouse and growth chamber trials. Sterilization of the chinampa soil resulted in a loss of the suppressive effect, thereby indicating that one or more biotic factors were responsible for the low incidence of nematode damage. Nine organisms were isolated from chinampa soil, which showed antinematodal properties in culture. Naturally occurring populations of plant-parasitic nematodes were of lower incidence in chinampa soil than in Chapingo soil.     

On navigating between friends and foes

The problem of determining the optimal straight path between a planar set of points is considered. Each point contributes to the cost of a path a value that depends on the distance between the path and the point. The cost function, quantifying this dependence, can be arbitrary and may be different for different points. An algorithm to solve this problem using an extension of the Hough transform is described. The range of applications includes straight-line fitting to a set of points in the presence of outliers, navigation, and path planning. The proposed extended Hough transform can be tuned to equivalent to well-known robust least-squares techniques, and allows efficient, approximate M-estimation     

Impact of deltamethrin impregnated mosquito nets on the transmission of malaria in the coastal lagoon area, Benin]

Neopterin has been determined in blood as a marker of cellular immune system activation. We studied cerebrospinal fluid (CSF) neopterin levels in children with neurologic diseases, and the following results were obtained: (1) CSF neopterin levels markedly increased at the acute phase of bacterial meningitis, aseptic meningitis, and encephalitis as compared with those in patients without neurologic diseased. (2) In the CSF of patients with bacterial meningitis and aseptic meningitis, neopterin levels decreased more rapidly than the total cell count and 2'5' oligoadenylate synthetase (2-5 AS) did. (3) CSF neopterin in patients with non-infectious neurologic diseases was almost equal to that in patients without neurologic diseases. (4) There was no correlation between CSF neopterin and other CSF values, such as total cell count, mononuclear cell count, protein, and 2-5 AS. These results suggest that CSF neopterin is a useful marker of inflammatory central nervous diseases.