Measurements of thermal-neutron capture cross-section of Cesium-135 by applying mass spectrometry

ABSTRACT

The thermal-neutron capture cross-section (σ₀) and resonance integral (I₀) were measured for the ¹³⁵Cs(n,γ)¹³⁶Cs reaction by an activation method and mass spectrometry. Because of difficulty in the preparation of pure ¹³⁵Cs samples, we used ¹³⁵Cs contained as an impurity in a normally available ¹³⁷Cs standard solution. An isotope ratio of ¹³⁵Cs and ¹³⁷Cs in a standard ¹³⁷Cs solution was measured by mass spectrometry to quantify ¹³⁵Cs. Cesium-135 impurity along with the ¹³⁷Cs standard solution was irradiated at the hydraulic conveyer of the research reactor in the Institute for Integral Radiation and Nuclear Science, Kyoto University. Wires of Co/Al and Au/Al alloys were used as neutron monitors to measure thermal-neutron fluxes and epi-thermal Westcott’s indices at an irradiation position. A gadolinium filter was used to measure the σ₀, and a value of 0.133 eV was taken as the cut-off energy. Gamma-ray spectroscopy was used to measure induced activities of ¹³⁷Cs, ¹³⁶Cs and monitor wires. On the basis of Westcott’s convention, the σ₀ and I₀ values were derived as 8.57 ± 0.25 barn, and 45.3 ± 3.2 barn, respectively. The value of σ₀ obtained in the present study agreed within the limits of uncertainties with the past-reported value of 8.3 ± 0.3 barn.     

Silver(I)-Ion-Mediated Cytosine-Containing Base Pairs: Metal Ion Specificity for Duplex Stabilization and Susceptibility toward DNA Polymerases

Spectroscopic characterization of Ag^I-ion-mediated C-Ag^I-A and C-Ag^I-T base pairs found in primer extension reactions catalyzed by DNA polymerases was conducted. UV melting experiments revealed that C-A and C-T mismatched base pairs in oligodeoxynucleotide duplexes are specifically stabilized by Ag^I ions in 1:1 stoichiometry in the same manner as a C-C mismatched base pair. Although the stability of the mismatched base pairs in the absence of Ag^I ions is in the order C-A≈C-T>C-C, the stabilizing effect of Ag^I ions follows the order C-C>C-A≈C-T. However, the comparative susceptibility of dNTPs to Ag^I-mediated enzymatic incorporation into the site opposite templating C is dATP>dTTP≫dCTP, as reported. The net charge, as well as the size and/or shape complementarity of the metal-mediated base pairs, or the stabilities of mismatched base pairs in the absence of metal ions, would be more important than the stability of the metallo-base pairs in the replicating reaction catalyzed by DNA polymerases.     

Coordinate-Based Evaluation of Two Dimensional Artefact Calibration Value as the Reference Standards for Coordinate Measuring Machines

Two dimensional standards are important materials which are used in the calibration and the verification of coordinate measuring machines. In several countries, the national metrology institutes or accredit laboratories provide the calibration services of the two dimensional standards such as ball plates, hole plates and grid plates. The metrological equivalence of the measurement standards among the calibration providers is validated through the key comparison program. In the previous key comparison for a ball plate and a hole plate, the equivalences among the participants’ calibration results were verified on the distances between the No. 1 ball/hole (i.e., the origins of the workpiece coordinates) and other balls/holes on the plates respectively. The essential measurands of the two dimensional standards are the coordinates of the feature points, however, the measurement equivalences on them have not been verified. In this study, the authors propose the coordinates-based evaluation of the reference values and their uncertainty in two dimensional standard calibration comparison.     

Urothelium-Specific Deletion of Connexin43 in the Mouse Urinary Bladder Alters Distension-Induced ATP Release and Voiding Behavior

Connexin43 (Cx43), the main gap junction and hemichannel forming protein in the urinary bladder, participates in the regulation of bladder motor and sensory functions and has been reported as an important modulator of day–night variations in functional bladder capacity. However, because Cx43 is expressed throughout the bladder, the actual role played by the detrusor and the urothelial Cx43 is still unknown. For this purpose, we generated urothelium-specific Cx43 knockout (uCx43KO) mice using Cre-LoxP system. We evaluated the day–night micturition pattern and the urothelial Cx43 hemichannel function of the uCx43KO mice by measuring luminal ATP release after bladder distention. In wild-type (WT) mice, distention-induced ATP release was elevated, and functional bladder capacity was decreased in the animals’ active phase (nighttime) when Cx43 expression was also high compared to levels measured in the sleep phase (daytime). These day–night differences in urothelial ATP release and functional bladder capacity were attenuated in uCx43KO mice that, in the active phase, displayed lower ATP release and higher functional bladder capacity than WT mice. These findings indicate that urothelial Cx43 mediated ATP signaling and coordination of urothelial activity are essential for proper perception and regulation of responses to bladder distension in the animals’ awake, active phase.     

Phragmites australis: a novel biosorbent for the removal of heavy metals from aqueous solution

Reed (Phragmites australis), a commonly used macrophyte in the wetlands constructed for water purification, was investigated as a new biosorbent for the removal of Cu(2+), Cd(2+), Ni(2+), Pb(2+) and Zn(2+) from aqueous solution. The metal adsorption capacity of reed biomass was improved significantly by water-wash, base- and acid-treatment. The maximum sorption of NaOH-pretreated reed biomass was observed near neutral pH for Cu(2+), Cd(2+), Ni(2+) and Zn(2+), while that for Pb(2+) was from an acidic range of pH 4.0 or higher. The maximum metal adsorption capacity on a molar basis assumed by Langmuir model was in the order of Cu(2+)>Ni(2+)>Cd(2+)>Zn(2+)>Pb(2+). Reed biosorbent showed a very high adsorption affinity value, which helps predict its high ability to adsorb heavy metals at low concentration. Desorption of heavy metals and regeneration of the biosorbent was attained simultaneously by acid elution. Even after three cycles of adsorption-elution, the adsorption capacity was regained completely and the desorption efficiency of metal was maintained at around 90%.     

In situ bioremediation of a cis-dichloroethylene-contaminated aquifer utilizing methane-rich groundwater from an uncontaminated aquifer

At a trichloroethylene (TCE)-contaminated site in Chikura, Chiba, Japan, TCE had spread over to the first and second aquifers over years. After 8 years of pumping and treatment, finally derivative of TCE, cis-dichloroethylene (c-DCE) remained only in the second aquifer. In this study, feasibility of a low cost in situ bioremediation utilizing groundwater of the third aquifer, which contained natural dissolved methane possibly derived from natural gas field nearby, to stimulate methane-oxidizing bacteria was examined. In vitro experiment showed that a mixture of the groundwater from the second and third aquifers stimulated a growth of methane oxidizing bacteria and enhanced c-DCE degradation. The groundwater of the third aquifer was introduced into the second aquifer in situ. The population of methanotrophs with high V(max) and K(m) for methane uptake increased, resulting in successful degradation of c-DCE at a monitoring well 2m downgradient of the injection well.     

Reappraisal of loading rate effects on sand behavior in view of seismic design for pile foundation

This study re-visits the effects of loading rate on sand behavior in view of seismic design of pile foundation. Based on an extensive literature review covering both element testing and model testing, the paper summarizes the current understanding of the loading rate effects. The paper then describes the development of test apparatus used in this study and presents the data obtained from a series of monotonically increasing triaxial compression tests on Toyoura sand, varying the strain rate in the range of 0.005%/s to 250%/s. A total of 36 tests were conducted on dry and saturated sand, both under drained and undrained conditions with two confining pressures. The experimental results confirm that the soil strength and the soil stiffness increase as the strain rate increase. This paper also concludes that the internal friction angle and deformation modulus increase when the strain rate is high. The implications of the loading rate effect on pile foundation design are then presented.     

Nanostructured poly(3-hexylthiophene-2,5-diyl) films with tunable dimensions through self-assembly with polystyrene

Poly(3-hexylthiophene-2,5-diyl) is among the most widely used conjugated polymers for opto-electronic applications. To enhance its properties, researchers have attempted to nanostructure this polymer using various processes including breath figure arrays, nanolithography and elaborated organic synthesis. We here demonstrate a simple process to nanostructure the conjugated polymer using self-assembly with polystyrene and selective removal of one of the phases. The influence of the molecular weight of each polymer on the thin film morphology was systematically studied by atomic force microscopy. Using this approach, we observe two types of nanostructure, namely, nanoporous and nanoisland structures, of which the dimensions can be tuned by modifying the molecular weight of each polymer in the blend. This simple process introduces a cost-effective alternative to produce thin films of conjugated polymer with average nano-features from 100 nm up to 500 nm which could be used in a wide range of applications.     

Detection of Multiple Blockages in Parallelized Microreactors

In a plant consisting of parallelized microreactors (MRs), the product quality is lowered because of a lack of flow uniformity among them when blockage occurs. It is not practical to install sensors in every MR from the viewpoint of cost when detecting the blocked MRs. In the previous study, the multiple blockage detection (MBD) method using a small number of sensors was proposed, but its performance became low when the number of sensors decreased. Here, the conventional algorithm for MBD is improved by considering the process behavior on blockage occurrence, and the effectiveness of the improved algorithm is demonstrated through a numerical case study. The effects of flow distributor types and sensor types on the MBD performance are numerically investigated.