Effect of Different Cosolvents on Transesterification of Waste Cooking Oil in a Microreactor

Biodiesel was prepared from waste cooking oil combined with methanol. The process was performed via transesterification in a microreactor using kettle limescale as a heterogeneous catalyst and various cosolvents under different conditions. n‐Hexane and tetrahydrofuran were selected as cosolvents to investigate fatty acid methyl esters (FAMEs). To optimize the reaction conditions, the main parameters affecting FAME% including reaction temperature, catalyst concentration, oil‐to‐methanol volumetric ratio, and cosolvent‐to‐methanol volumetric ratio were studied via response surface methodology. Under optimal reaction conditions and in the presence of the cosolvents n‐hexane and tetrahydrofuran, high FAME purities were achieved. Considering the experimental results, the limescale catalyst is a unique material, and the cosolvent method can reduce significantly the reaction time and biodiesel production cost.     

Nanostructured Carbide-Free Bainite Formation in Low Carbon Steel

It is an important challenge to reduce the carbon content in nanostructured bainitic steels for commercialization purposes while still being able to gain the desired microstructural characteristics in nanoscale and not to deteriorate the strength-ductility combinations. That is the point at which an appropriate heat treatment procedure design would be an important parameter. This article aims to investigate how to obtain nanostructured bainite in steel with 0.26 wt% carbon content by applying multi-step austempering procedures. One-, two- and three-step austempering processes have been implemented, and proper heat treatment temperatures and approaches were selected based on dilatometry tests. Results indicated that it has become possible to achieve bainitic ferrites and austenite films with overall thicknesses of 164, 145 and 132 nm and 134, 105 and 90 nm at the end of one-, two- and three-step austempering heat treatments, respectively. Meanwhile, microstructural characteristics resulted in enhanced mechanical properties with ultimate tensile strength (UTS) of 1435, 1455 and 1428 MPa in combination with elongation levels of 15.4, 13.6 and 11.4% after implementing those heat treatments. Finally, it has been shown that applying the multi-step austempering heat treatments resulted in enhanced yield strength and impact toughness values due to the microstructural characteristics and proper heat treatment procedure design.     

An optimized evacuation model with compatibility constraints in the context of disability: an ancient-inspired Giza Pyramids Construction metaheuristic approach

Applied Intelligence - In recent years, the number and severity of natural disasters have increased. These disasters always carry the risks of mortality and injury. But its mortality risks are much...     

Selective Laser Melting process optimization of Ti–Mo–TiC metal matrix composites

Selective Laser Melting (SLM) was used to process a powder mixture of CP Ti, 6.5 wt% Mo and 3.5 wt% Mo₂C. The process parameters were optimized to obtain full-density, crack free parts. After the in situ decomposition of Mo₂C in favor of the formation of TiC, the material consisted of a homogeneous dispersion of submicrometer sized TiC platelets in a β-(Ti,Mo) matrix exhibiting a high hardness up to 550 HV and compressive yield stress of 1164 ± 37 MPa. The microstructure and mechanical properties could be tailored by variation of the process parameters within the high-density processing window, as well as through post-process heat treatments.     

A design method for substrate integrated waveguide electromagnetic bandgap (SIW-EBG) filters

An efficient design method for substrate integrated waveguide electromagnetic bandgap (SIW-EBG) filters is proposed which provides direct dimensional synthesis approach for desired filter objectives without using network representations. The method is applied to the design of an X band SIW-EBG filter and its response is compared with HFSS (high frequency structure simulator) simulations for validation purposes. Fairly good agreement between the results shows the applicability of the proposed method for SIW-EBG filter design.     

In-Process Monitoring of Nickel-Based Super Alloy Grinding Using the Acoustic Emission Method

Russian Journal of Nondestructive Testing - One of the most prevalent problems in grinding nickel-based super alloys is grinding wheel loading phenomenon which is the chip accumulation in free...     

Effect of geometry and green density on the anisotropic sintering shrinkage of axisymmetric iron parts

Sintering shrinkage of prior cold compacted iron rings with different geometry (height to wall thickness ratio) and green density in the 6.5–7.3?g/cm³ range was investigated. It displays a minimum at an intermediate green density. Axial, tangential and radial shrinkages are different, due to the gradients of green density along the axial and the radial directions. Therefore, the effect of height on shrinkage and its anisotropy is the result of their effect on the stress distribution in the green parts during cold compaction, and the resulting green density and deformation experienced by the powder. Anisotropy decreases on increasing shrinkage.     

Conceptual design and statistical overview on the design of a passive DMFC single cell

A conceptual design and statistical overview about passive direct methanol fuel cells that have been fabricated from 2002 to 2013, is performed [1–70]. The major components of passive DMFCs such as: active area, type of Nafion, catalyst loading on the anode and cathode side, characteristics and designs of current collectors (CC), and also the optimum methanol concentration which resulted in the best performance are categorized and studied statistically and individually. Finally, the best combination for the design and fabrication of a reliable passive DMFC is recommended. Obtained results indicated that a MEA with 4 cm² active area, Nafion 117 and 4 mg/cm² Pt/Ru at the anode and 2 mg/cm² Pt black at the cathode (or 4 mg/cm² Pt/Ru at the anode – 4 mg/cm² Pt black at the cathode) as the catalyst loading, which is sandwiched between two stainless steel perforated current collectors that are coated by Pt (or Gold) could be a reliable design for a passive direct methanol single cell.     

Anisotropic diffusion for noise removal of band pass signals

A noise removal method for band pass signals based on the anisotropic diffusion algorithm originally put forward by Perona and Malik is proposed in this paper. The anisotropic smoothing algorithm proposed here is for band pass signals modulated with a constant carrier frequency. A partial differential equation to smooth band pass noisy signals is derived. The propagator of this differential equation is also analytically calculated in this paper. An appropriate linear operator is then considered here for such band pass signals to form an anisotropic diffusion algorithm. The algorithm proposed here demonstrates better performance for band pass noisy signals containing discontinuities in comparison with the traditional Perona-Malik (PM) algorithm and is robust in the presence of excessive noise with SNR less than unity.     

A Comprehensive Experimental Study on Finishing Aluminum Tube by Proposed UAMAF Process

In this paper, a new noncontact ultrasonic magnetic abrasive finishing mechanism is presented. An ultrasonic vibration producer is used to vibrate the permanent magnets. The ferromagnetic steel grits in the created magnetic field form a flexible finishing tool. To take advantage of cavitation collapse pressure, the finishing zone components are immersed in water. The present work also studies the effect of parameters, i.e., time duration for finishing and working gap between magnetic poles and the workpiece on the surface roughness (Ra). The microscopic pictures and the roughness profile diagrams demonstrate the advantages of the proposed method.