A non-contact method for part-based process performance monitoring in end milling operations

Surface response to excitation (SuRE) method was originally developed for structural health monitoring (SHM) applications. SuRE was used to evaluate the performance of completed milling operations. The method generates surface waves on the plate and studies the spectrum changes at selected points to detect defects and change of compressive forces. In this study, the length, depth, and width of a slot were changed step by step. The surface of the aluminum plate was excited in the 20–400 kHz range with a piezoelectric element. A laser scanning vibrometer was used to monitor the vibrations at the predetermined grid points after the dimensions of the slot were changed methodically. The frequency spectrums of measured vibrations were calculated by using the Fast Fourier Transformation (FFT). The sums of the squares of the differences (SSD) of the spectrums were calculated to evaluate the change of the spectrums. The SuRE method was able to determine if the dimensions were changed in each case at all the selected points. The scanning laser vibrometer is not feasible to be used at the shop floor. However, the study demonstrated that a piezoelectric element attached to any of the grid points would be able to evaluate the completed machining process.     

Comparison Study of Fourier and SVD Method for Plasma Mode Analysis in Tokamaks

Fourier analysis and Singular Value Decomposition (SVD) are two familiar methods for mode detection in tokamaks. In this article this two methods, fourier and SVD, have compared. The results show fourier analysis in m ≥ 3 and when the energy is balanced between modes could not recognize the correct mode number. The SVD analysis is cited method for all modes.     

Supertough (Polyamide 6)/(acrylonitrile butadiene rubber) nano alloy through in situ polymerization of caprolactam in the presence of acrylonitrile butadiene rubber nanophase

In this work, polymerization of caprolactam (CL) was carried out in the presence of acrylonitrile butadiene rubber (NBR) during the reactive melt‐mixing process. During shear mixing, NBR particles swelled and dissolved in the molten CL, which led to separation and distribution of rubber particles to nanoscale in the dissolution stage. Then, in an internal mixer, supertough Polyamide 6 was prepared via melt polymerization of CL/NBR mixture, sodium caprolactam as a catalyst, and hexamethylene diisocyanate as an activator. The effects of various concentrations of catalyst and activator on the initiation time of the reaction were determined. Physical and mechanical properties of different formulations prepared via reactive melt blending were determined by tensile and impact measurements, differential scanning calorimetry, Fourier‐transform infrared spectroscopy, X‐ray scattering techniques, transmission electron microscopy, and dynamic mechanical thermal analysis. Experimental results showed that a recipe with 3% nitrile rubber in a CL/NBR mixture enhances the physical and mechanical properties the best, compared with other formulations. This condition led to the formation of NBR nanospheres during melt polymerization of Polyamide 6 as well. J. VINYL ADDIT. TECHNOL., 21:116–121, 2015. © 2014 Society of Plastics Engineers     

Prediction of creep crack growth properties of P91 parent and welded steel using remaining failure strain criteria

Old grades of creep resistant materials such as P11 and P22 have been studied in depth and data and prediction models are available for design and fitness for service assessment of creep rupture, creep crack growth, thermo-mechanical fatigue, etc. However, as the 9%Cr material is relatively new, there is relatively limited data available and understanding with respect to quantifying the effect of variables on life prediction of components fabricated from P91 is more difficult. Since grade P91 steel was introduced in the 1980s as enhanced ferritic steel, it has been used extensively in high temperature headers and steam piping systems in power generating plant. However, evidence from pre-mature weld failures in P91 steel suggests that design standards and guidelines may be non-conservative for P91 welded pressure vessels and piping. Incidences of cracking in P91 welds have been reported in times significantly less than 100,000 h leading to safety and reliability concerns worldwide. This paper provides a review and reanalysis of published information using properties quoted in codes of practice and from recent research data regarding the creep crack growth of P91 steel, and uses existing models to predict its behaviour. Particular areas where existing data are limited in the literature are highlighted. Creep crack growth life is predicted based on short-term uniaxial creep crack growth (CCG) data. Design and assessment challenges that remain in treating P91 weld failures are then addressed in light of the analysis.     

Pipe damper,Part I: Experimental and analytical study

In this paper the behavior of steel pipes, filled and unfilled with concrete, is studied under cyclic shear to examine the possibility of their use as a seismic damper. Two specimens of steel pipes filled inside with concrete are tested under monotonic and cyclic shear. Four other specimens of bare steel pipes are tested under fully reversed cyclic shear loading. The results show that the bare steel pipes are capable of absorbing a great amount of energy under a severe cyclic shear loading with a stable hysteretic behavior. This behavior is also simulated using the finite element method. Then, parametric studies are performed to investigate the effects of variations in geometrical properties of the pipe on its hysteretic behavior. A simplified bi-linear model is proposed to approximate the hysteretic behavior of the steel pipe as a metallic-yielding damper.     

Experimental and analytical study on channel shear connectors in fiber-reinforced concrete

This paper investigates, experimentally and analytically, the capacity of channel shear connectors embedded in normal and polypropylene (PP) concrete. Limited testing is used to assess the accuracy of a proposed nonlinear finite element model for typical push-out test specimens. Using this model, an extensive parametric study is performed to arrive at a prediction for shear capacity of channel connectors in PP concrete. An equation, for inclusion in design codes, is suggested for the shear capacity of these connectors when used in PP concrete.     

An adaptive latency mitigation scheme for massively multiuser virtual environments

As massively multiuser virtual environments (MMVEs) expand in terms of size and user population, they tend toward using P2P architectures as a way to provide scalability without the need for large centralized resources. Distributed hash table (DHT)-based networks have been introduced as a promising option for overlay-based distributed massively multiuser virtual environment applications. However, overlay latency stretch seriously affects MMVE performance where QoS is crucial for real-time user collaboration. This work includes a series of efforts in the alleviation of such undesired latency. Our approach to latency mitigation consists of two phases. First, we propose a position-based ID assignment approach to minimize message hop-count by exploiting the clustered pattern of traffic exchange among MMVE users. Second, we introduce a new ant-based distributed neighbor selection scheme that can be used by MMVE users to select the best neighbors within their areas of interest. In order to evaluate the performance of this heuristic approach, we model the neighbor selection problem in the form of a network flow problem and use its solution as an optimality bound to compare the results. Simulation results demonstrate that the proposed algorithms will compensate for DHT latency stretch to a high extent and the performance of the resulting system would closely follow the optimal bound while communication overhead is negligible.     

Performance evaluation of a reservation random access scheme for packetized wireless systems with call control and hand-off loading

We consider a packet switched wireless network where each cell's communication channel is shared among packet voice sources. In this paper, we present a method for the design and analysis of wireless cells using a reservation random access (RRA) scheme for packet access control. This scheme is integrated with a call admission control procedure. We model the state process of a single cell as a vector Markov chain. We compute the steady state distribution of the Markov chain. This result is used to calculate the packet dropping probability and the call blocking probability. By setting limits on maximum permissible levels for the call blocking probability and the packet dropping probability, we obtain the Erlang capacity of a single cell, with and without hand-off traffic. For an illustrative RRA scheme, the Erlang capacity of a single cell is shown to be about twice that attained by a comparable fixed assigned TDMA scheme. We show that a cellular network using this RRA scheme and which applies can be no blocking of hand-off calls, exhibits similar call capacity levels.This work is supported by a University of California MICRO and Pacific-Bell Grant No. 94-107.