落葵浆果天然染料提取及对羊毛织物的染色性能

文章主要研究用水浸法提取落葵浆果天然染料及研究浸提液对羊毛织物的染色性能。以水为提取剂提取落葵浆果天然染料,探讨提取工艺中料液比、提取温度及时间等因素对落葵浆果天然染料提取效果的影响。研究结果表明,落葵浆果水浸提法优化工艺为:料液比1∶20、提取温度70℃、提取时间30 min。落葵浆果天然染料可以对羊毛织物进行染色,媒染染色与直接染色相比,染色深度深且会呈现不同的颜色。由于媒染剂的络合作用,媒染染色色牢度比直接染色普遍高1~2级。     

核桃雄花中总多酚提取工艺的研究

采用单因素和正交试验研究核桃雄花中多酚类物质的最佳提取工艺条件。通过对4种不同溶剂(无水乙醇、甲醇、丙酮和乙酸乙酯)在相同试验条件下的浸提效果比较发现,甲醇是核桃雄花中总酚类物质的最佳提取试剂。然后分别采用常规水浴浸提法和超声波辅助浸提法对甲醇体分数、浸提温度、浸提时间和料液比等因素进行研究,在确定最佳单因素水平的基础上,再利用正交试验优化以甲醇为浸提剂的提取工艺条件,试验得出超声波辅助浸提法具有用时短、总多酚提取量高的优点,其最佳工艺条件为:料液比1∶30(g/m L)、甲醇溶液体积分数30%、温度70℃、浸提时间10 min。在此条件下,核桃雄花中的总多酚含量可达6.56%,明显高于其他条件下的。     

Removal of imidacloprid and acetamiprid from tea infusions by microfiltration membrane

Removal of imidacloprid and acetamiprid in tea infusions by microfiltration membrane using dead‐end model was investigated in the present study. The results showed that microfiltration significantly promoted the removal of both pesticides (P < 0.05) in tea infusions. Furthermore, the extent of removal was strongly influenced by the pore size of membrane, operational pressure and the concentrations of tea infusions. The initial concentration of imidacloprid and acetamiprid showed no significant effect on their removal rates. The maximum removal rates were 79.7% for imidacloprid and 81.9% acetamiprid. The changes in major chemical components of tea infusions after microfiltration were evaluated. The results indicated that microfiltration caused no considerable changes in total polyphenols and total free amino acids, and small but statistically significant losses (6.3–18.0%) of eight catechins and three methylxanthines when filtration volume reached to 200 mL. The present study validated the application of microfiltration as a potentially feasible and promising method for the removal of imidacloprid and acetamiprid residues from tea infusions.     

Effect laws and mechanisms of different temperatures on isothermal tensile fracture morphologies of high-strength boron steel

The fracture behaviour and morphologies of high-strength boron steel were investigated at different temperatures at a constant strain rate of 0.1 s-1 based on isothermal tensile tests. Fracture mechanisms were also analyzed based on the relationship between microstructure transformation and continuous cooling transformation(CCT) curves. It is found that 1) fractures of the investigated steel at high temperatures are dimple fractures; 2) the deformation of high-strength boron steel at high temperatures accelerates diffusion transformations; thus, to obtain full martensite, a higher cooling rate is needed; and 3) the investigated steel has the best plasticity when the deformation temperature is 750 °C.