Effect of Sb implantation on copper silicides formation and morphology after annealing of Cu/Si structures

In this work, the solid state reaction between a thin film of copper and silicon has been studied using Rutherford backscattering spectroscopy, X-ray diffraction, scanning electron microscopy and microprobe analysis. Cu films of 400 and 900 Å thicknesses are thermally evaporated on Si(1 1 1) substrates, part of them had previously been implanted with antimony ions of 5×10¹⁴ or 5×10¹⁵ at. cm⁻² doses. The samples are heat-treated in vacuum at temperatures in the range 200–700 °C for various times. The results show the growth and formation of Cu₃Si and Cu₄Si silicides under crystallites shape dispatched on the sample surface, independently of the implantation dose. On the other hand, it is established that the copper layer is less and less consumed as the antimony dose increases, resulting in the accumulation of Sb⁺ ions at silicide/Si interface and in the silicide layer close to surface. The exposure of samples to air at room temperature shows the stability of Cu₄Si phase whereas the Cu₃Si silicide disappears to the benefit of the silicon dioxide formation. The observed phenomena are discussed.     

P204萃取分离锑铁工艺研究

萃取分离锑铁是脆硫锑铅矿矿浆电解工艺过程的一个环节。P2 0 4可选择性地在NH4 Cl介质溶液中萃取铁。在 35 %(体积百分数 )P2 0 4、相比 (O/A) 1∶1、3级连续逆流萃取条件下 ,铁萃取率达 80 %～ 84%,锑、银基本不被萃取。含Fe总 1～ 1 4g/L的萃余液可返回矿浆电解循环使用。     

Complementary effects of solid lubricants in the automotive brake lining

An experimental investigation was carried out to examine the tribological behavior of NAO (non-asbestos organic) type brake linings containing different volume ratios of graphite and antimony trisulfide (Sb₂S₃). A scale dynamometer was used for friction tests and particular emphases were given to the effect of applied pressure, sliding speed, and temperature on the coefficient of friction according to the relative amounts of the two solid lubricants. Results showed that the brake linings with both solid lubricants exhibited better friction stability and less speed sensitivity than the friction materials containing a single solid lubricant. In particular, the brake lining containing higher concentrations of graphite showed better fade resistance than others during high-temperature friction test.     

Catalytic dehydrogenation of ethylbenzene with carbon dioxide: promotional effect of antimony in supported vanadium–antimony oxide catalyst

Alumina-supported vanadium oxide, VO_x/Al₂O₃, and binary vanadium–antimony oxides, VSbO_x/Al₂O₃, have been tested in the ethylbenzene dehydrogenation with carbon dioxide and characterized by S_BET, X-ray diffraction, X-ray photoelectron spectroscopy, hydrogen temperature-programmed reduction and CO₂ pulse methods. VSbO_x/Al₂O₃ exhibited enhanced catalytic activity and especially on-stream stability compared to VO_x/Al₂O₃ catalyst. Incorporation of antimony into VO_x/Al₂O₃ increased dispersion of active VO_x species, enhanced redox properties of the systems and formed a new mixed vanadium–antimony oxide phase in the most catalytically efficient V_0.43Sb_0.57O_x/Al₂O₃ system.     

含砷、锑、碳难处理金精矿焙烧氰化提金工艺研究

镇沅含砷、锑、碳难处理金精矿直接氰化金浸出率小于 10 % ,采用常规焙烧 -焙砂氰化提金工艺金浸出率仅达到 73 2 % ,而采用先行除锑 ,再焙烧脱除硫、碳、砷的提金工艺方案 ,金氰化浸出率达到90 4 % ,同时锑可作为锑精矿外售 ,经济效益明显。     

Re-optimization of the binary Sb − Se system aided by ab-initio calculations

Based on the ab-initio calculations the thermodynamics of the Sb₂Se₃ intermediate phase was modeled and used in the calculations of the Sb–Se phase diagram together with the thermodynamic properties of liquid phase elaborated by the association model. The modeled heat capacity of Sb₂Se₃ phase shows excellent agreement with the experiment data available in the literature in the wide temperature range. The calculated equilibrium lines of the Sb–Se phase diagram good correlate with the experimental ones. The determined thermodynamic parameters can be applied in future calculations of the high-ordered systems and for determination of the Sb₂Se₃ thermoelectric properties.     

Synthesis of nano Sb-encapsulated pyrolytic polyacrylonitrile composite for anode material in lithium secondary batteries

A novel process was proposed to synthesize nano Sb-encapsulated pyrolytic polyacrylonitrile composite for anode material in lithium secondary batteries. The preparation started with the dissolution of SbCl₃ and polyacrylonitrile (PAN) in dimethylformamide (DMF) solution, followed by the addition of KBH₄ to reduce Sb³⁺ in the solution. The Sb composite was obtained by pyrolysis of the Sb/PAN mixture that precipitated out when the DMF solution was added by plentiful water. The TEM analysis showed that about 100-200 nm Sb particles were embedded by the pyrolyzed PAN, which provided a conductive matrix to relieve the morphological change of Sb during electrochemical cycling. As-prepared composite presented good cycleability for lithium storage. The proposed process paves an effective way to prepare high performance alloy based composite anode materials for high performance lithium-ion batteries.     

超细氧化锑阻燃剂的研究进展

综述了氧化锑阻燃剂的超细化、表面处理、复合功能化方面的发展方向和研究热点。     

铸造锑青铜材料研究

研究了锑、锌、锰等合金元素对锑青铜的组织和性能的影响，经过大量试验，研制出具有良好综合性能的新型锑青铜材料，是目前替代锡青铜材料的理想材料。     

Using of textured polycrystalline SbSI in actuators

This paper presents the design and fabrication of a light deflector made from textured polycrystalline antimony sulfoiodide (SbSI) obtained by gradient freezing during the rapid quenching from the liquid state. The piezoelectric and electrostriction parameters of the textured polycrystalline SbSI are evaluated from the reflection measurements. First time the electrostrictive constant of this material (4.6(1) × 10⁻¹³ m²/V²) is reported.