Relationships of tensile strength with crosslink density for the high-carbon black-filled EPDM compounds with various softeners

Equilibrium swelling and rheological tests were adopted to systematically investigate the effects of softener type and dosage on the crosslink densities. The results turned out that the chemical crosslink density could be distinguished from the physical crosslink density by comparing the results of equilibrium swelling and rheological tests. The liquid butadiene (LB) as a softener leads to the greatest reduction in crosslink density, followed by polyethylene wax (PW) and paraffinic oil (PO). The tensile strength decreases with increasing PO content while shows peak values with increase of LB and PW contents. The dependencies of chemical crosslink density on the aging time under 150°C are quite different for the three softeners, which can be expected from the double crosslinking networks consisting of small softener and large main crosslinking networks. Further investigation has been performed to correlate the tensile strength with chemical crosslink density of ethylene propylene diene monomer elastomer vulcanizates. Three different linear relationships can be obtained for the softeners independent of the aging time. It can now be expected from this study that the role of some new softeners in rubber compounds is not only confined to plasticization but also forms crosslinking networks in the peroxide-cured rubbers.     

Damage evolution in polymer due to exposure to high-pressure hydrogen gas

The use of hydrogen as a fuel is increasing exponentially, and the most economical way to store and transport hydrogen for fuel use is as a high-pressure gas. Polymers are widely used for hydrogen distribution and storage systems because they are chemically inert towards hydrogen. However, when exposed to high-pressure hydrogen, some hydrogen diffuses through polymers and occupies the preexisting cavities inside the material. Upon depressurization, the hydrogen trapped inside polymer cavities can cause blistering or cracking by expanding these cavities. A continuum mechanics–based deformation model was deployed to predict the stress distribution and damage propagation while the polymer undergoes depressurization after high-pressure hydrogen exposure. The effects of cavity size, cavity location, and pressure inside the cavity on damage initiation and evolution inside the polymer were studied. The stress and damage evolution in the presence of multiple cavities was also studied, because interaction among cavities alters the damage and stress field. It was found that all these factors significantly change the stress state in the polymer, resulting in different paths for damage propagation. The effect of adding carbon black filler particles and plasticizer on the damage was also studied. It was found that damage tolerance of the polymer increases drastically with the addition of carbon black fillers, but decreases with the addition of the plasticizer.     

橡胶卷材挤出连续硫化生产线的结构特色与工作原理

介绍了橡胶防水防腐卷材挤出连续硫化生产线的结构、特点和工作原理;指出在目前国内同类设备中,该生产设备具有先进性,并可替代引进设备。     

Dynamic vulcanisation of EPDM/PE-based thermoplastic vulcanisates studied along the extruder axis

Simple blending and dynamic vulcanisation of EPDM/PE blends using the resol/SnCl₂ system was studied in an extruder using a series of sampling devices. The melting of the PE pellets occurs just in front of and in the first kneading zone. Upon complete melting of the PE phase, the EPDM/PE blends reach very quickly their final morphology. Crosslinking of the EPDM phase to high levels occurs already when the PE phase is not yet fully molten. The higher the EPDM content, the higher the viscous dissipation, the higher the melt temperature and, consequently, the higher the crosslinking rate. For the EPDM/PE (50/50; w/w) TPV a transition from continuous via co-continuous to fully dispersed EPDM is observed, which is driven by crosslinking. Although the degree of crosslinking of the EPDM rubber is very high, this does not prevent phase inversion of the blend. The EPDM/PE interface is rather blurred, because PE crystalline lamellae are growing into the EPDM domains, probably because of the high compatibility between PE and EPDM (60 wt% of ethene). This study shows that dynamic vulcanisation in extruders proceeds quite differently from that in batch kneaders, where melting, mixing and crosslinking are separated in time. In extruders mass and heat transport, melting of the thermoplastic, morphology development (including dispersion and phase inversion), distribution and dissolution of (crosslinking) chemicals and crosslinking of the rubber do not occur as independent phenomena, but mutually and/or continuously interact.     

PP/EPDM/CaCO_3三元共混体系的脆韧转变研究

采用扫描电镜和材料力学性能试验方法研究了ＰＰ／ＥＰＤＭ／ＣａＣＯ３三元体系中ＣａＣＯ３的表面处理与其材料的缺口冲击韧性及产生脆韧转变现象之间的关系。实验结果及分析表明：体系中分散相颗粒周围向ＰＰ基体扩散、渗透或与之共结晶的ＥＰＤＭ部分是增韧ＰＰ的有效成分；较好的表面处理条件下，体系中加入较少量的ＥＰＤＭ即可使材料缺口冲击韧性和拉伸模量值同时达到较好水平。     

EPDM/PP热塑性弹性体相态研究

采用透射电镜(TEM)研究动态硫化EPDM/PP热塑性弹性体制备工艺及增容改性对形态结构的影响,研究发现通过添加增容剂可使EPDM相呈颗粒分布于连续相中。     

三元乙丙橡胶卷材在地下防水工程中的应用

地下防水工程既是一项系统工程，又是一项隐蔽工程，如何选择防水材料和控制工程质量显得到关重要。本文结合工程实例，介绍了三元乙丙橡胶卷材在地下防水工程中的应用，分析了三元乙丙卷材的特点，提出了地下水的技术方案，施工操作要求，质量过程控制要点和施工注意项，本文对三元乙丙卷材的工程应用具有指导和借鉴意义。     

Thermoplastic elastomeric composition based on maleic anhydride–grafted ground rubber tire

Ground rubber tire (GRT) powder was maleated in an internal mixer using maleic anhydride and dicumyl peroxide at 160°C. Maleated GRT was characterized by using X‐ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, wettability, and differential scanning calorimetry. The physical properties of the dynamically vulcanized 60 : 40, rubber : plastic composition based on acrylated high‐density polyethylene as the plastic phase and ethylene propylene diene rubber containing maleated GRT as the rubber phase were found to be greater than the corresponding composition containing nonmaleated GRT. The blend was found to be reprocessable, like themoplastic elastomers. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 370–378, 2002; DOI 10.1002/app.10348     

Surface tailoring of an ethylene propylene diene elastomeric terpolymer via plasma‐polymerized coating of tetramethyldisiloxane

In the research presented here, we explore the use of a low‐energy plasma to deposit thin silicone polymer films using tetramethyldisiloxane (TMDSO) (H(CH₃)₂? Si? O? Si? (CH₃)₂H) on the surface of an ethylene propylene diene elastomeric terpolymer (EPDM) in order to enhance the surface hydrophobicity, lower the surface energy and improve the degradation/wear characteristics. The processing conditions were varied over a wide range of treatment times and discharge powers to control the physical characteristics, thickness, morphology and chemical structure of the plasma polymer films. Scanning electron microscopy (SEM) shows that pore‐free homogeneous plasma polymer thin films of granular microstructure composed of small grains are formed and that the morphology of the granular structure depends on the plasma processing conditions, such as plasma power and time of deposition. The thicknesses of the coatings were determined using SEM, which confirmed that the thicknesses of the deposited plasma‐polymer films could be precisely controlled by the plasma parameters. The kinetics of plasma‐polymer film deposition were also evaluated. Contact angle measurements of different solvent droplets on the coatings were used to calculate the surface energies of the coatings. These coatings appeared to be hydrophobic and had low surface energies. X‐ray photoelectron spectroscopy (XPS) and photoacoustic Fourier‐transform infrared (PA‐FT‐IR) spectroscopy were used to investigate the detailed chemical structures of the deposited films. The optimum plasma processing conditions to achieve the desired thin plasma polymer coatings are discussed in the light of the chemistry that takes place at the interfaces. Copyright © 2004 Society of Chemical Industry