压水堆硼稀释事故的计算

一、概述核电厂压水堆的初始过剩反应性是通过控制捧、固体可燃毒物和溶解在主回路冷却剂中的硼酸等三种方式联合控制的。随着反应堆的燃耗和裂变毒物的积累,堆的过剩反应性不断减少,需要通过化容系统,控制硼酸的浓度来进行补偿。如果化容系统发生故障或操作员误操作,就会给回路注入无硼或低于规定浓度的补给水,给反应堆引入正反应性,造成硼稀释事故。按核安全法规的要求,应对换料、冷停堆、热停堆和启动等工况进行计算,并要求在这些     

万家寨引黄南干线二级泵站出水压力平洞混凝土衬砌裂缝成因与处理

分析引黄南干二级泵站出水压力平洞混凝土村砌裂缝成因以及处理办法     

Theoretical investigation on the steady-state natural circulation characteristics of a new type of pressurized water reactor

1 Introduction With respect to the inherent safety of nuclear re- actors, application of passive systems/components including natural circulation phenomena as the main mechanism is intended to simplify the safety-related systems and to improve their reliability, to reduce the effect of human errors and equipment failures, and to provide more time to enable the operators to prevent or mitigate serious accidents. Natural circulation is the main mode of heat removal for removing decay heat from t…     

真空增压铸造技术及其应用前景

详细论述了真空增压铸造的技术原理、工艺特性及技术优点。结合铝合金铸件大型、复杂、薄壁、整体化和高气密性的发展趋势，针对性地分析了真空增压铸造技术推广应用的适应性，并提出了相应的技术对策。     

Preliminary study of parameter uncertainty influence on Pressurized Water Reactor core design

Sub-channel analysis can improve the accuracy of reactor core thermal design. However, the important initial parameters contain various uncertainties during reactor operation. In this work, the Sub-channel Analysis Code of Supercritical reactor (SACOS) code, which is also applicable for Pressurized Water Reactor (PWR), was used to study the coolant flow characteristic and fuel rod heat transfer characteristic of 1/8 assembly which has the maximum linear power density in 300 MWe PWR core firstly. Then the Wilks' method and Response Surface Method (RSM) were utilized to determine the influence of sub-channel input parameters uncertainties on the highest temperature of reactor core fuel rod and Minimum Departure from Nucleate Boiling Ratio (MDNBR). The results show that in the most conservative conditions, the maximum temperature of the fuel rod and MDNBR were 2167.4 °C and 1.08, respectively. Considering the uncertainties of assembly inlet flow rate, inlet coolant temperature and system pressure, the 95% probability values (with 95% confidence) of fuel rod maximum and MDNBR calculated using response surface methodology were 2144.0 °C and 1.6, while they were 2137 °C and 1.74 calculated by Wilks' approach. Results show that the uncertainty analysis methods can provide larger reactor design criteria margin to improve the economy of reactor. Furthermore, the code was developed to have the capacity to perform the uncertainty study of sub-channel calculation.     

Nonlinear dynamic output-feedback power-level control for PWRs: A shifted-ectropy based design approach

Nuclear fission energy is currently the sole energy that can substitute fossil in a centralized way and great amount with commercial availability and economic competitiveness. Power-level control is one of the key techniques which provide safe, stable and efficient operation for nuclear power plants. The physically-based regulation theory is definitely a promising trend of modern control theory, which can provide a control design method that suppresses the unstable part of the system dynamics and remains the stable part. Usually, control laws designed by the physically-based control theory have a simple form and high performance. Stimulated by this, a novel nonlinear dynamic output feedback power-level control law is established in this paper for the pressurized water nuclear reactors (PWRs) based upon its natural dynamic features. This newly-developed controller guarantees not only the globally asymptotic closed-loop stability but also the satisfactory transient performance through properly adjusting the feedback gains. Furthermore, this controller has the L₂ disturbance attenuation performance. Numerical simulation results not only verify the correctness of the theoretical results but also illustrate the high control performance.     

A unified heat transfer model in a pressurized volumetric solar receivers

In the present work, we developed an overall mathematical model adequately describing the main heat transfer processes in a pressurized volumetric receiver. The key components, a windowed cavity, incorporating with the irradiated surface of the absorber, were theoretically modeled as a closed diffuse-gray surfaces system. Accordingly, a boundary condition for the absorber concerning its porous structure surface was developed using net radiation method (NRM) under local thermal non-equilibrium (LTNE) condition. The same method is also applied to the back cavity. Then a modified P1 approximation with collimated irradiation was introduced to incorporate the radiation transfer penetrating in the absorber. The major characteristic of the heat transfer behavior combining radiation, thermal conduction, and convection in the windowed cavity, absorber and the back cavity, are detailedly presented. Also, the key design parameters, such as those relating to pore structure (φ and d_p), the volumetric heat transfer coefficient h_v, the emissivity ε for window and absorber, and their thickness L_a and L_g were systematically analyzed. Optimization design can be carried out for both of the solar thermal system and the receiver itself in the future work based on our model.     

Encapsulation of propolis flavonoids in a water soluble polymer using pressurized carbon dioxide anti-solvent crystallization

This study investigated the pressurized carbon dioxide anti-solvent co-precipitation process (abbr. PAS) on encapsulation of propolis with water soluble polyethylene glycol (PEG). The extent to which recovery of propolis flavonoids, total yield, amount of propolis (i.e. drug content) affects the precipitation was examined using a two-factor central composite schemed experimental design method. Analysis results indicated that the drug content and total yield of the precipitates are conversely related to each other in the PAS process. Additionally, micro-sized amorphous particulates of propolis encapsulated on the surface of PEG were generated, as evidenced by chromatography and X-ray diffraction analyses. Total yield of the PAS co-precipitation process reached 88%, and recovery of propolis flavonoids achieved 97%. Experimental results also indicated that the concentration ratio of propolis to PEG in the feed more significantly affects the drug content than that of the pressure factor. Moreover, nearly spherical and aggregated micro-sized co-precipitated particulates are more soluble in an aqueous solution than those of ethanol extracts.     

From supercritical carbon dioxide to gas expanded liquids in extraction and chromatography of lipids

Analytical‐scale extraction and chromatography of oils, fats and other liposoluble compounds can be achieved by using supercritical carbon dioxide as a solvent. Since the 90's when supercritical fluid chromatography (SFC) was a hot topic, this technology has developed into a robust, modern analytical technique that uses any proportions of compressed CO₂ mixed with an organic solvent. Supercritical fluid extraction (SFE) on the other hand is only recently starting to reform in a similar way, towards the use of more robust extraction system and enabling mixing of compressed CO₂ with larger proportions of organic solvents. In this Feature article, the development of SFC and SFE into what options we have today is described, including the latest trend of using CO₂‐expanded liquid (CXL) as extraction solvent for lipids.     

GPJ-120型加压过滤机在太原选煤厂的应用

分析了太原选煤厂浮选精煤脱水系统存在的问题，介绍了应用加压过滤机后的工艺效果，实践证明，加压过滤机过滤处理能力大，滤饼水分低，自动化程度高。