电压对电刷镀三价铬镀层性能的影响

在45钢表面电刷镀得到三价铬镀层,镀液组成和工艺条件为:Cr2(SO4)36H2O 0.4 mol/L,甲酸铵0.5 mol/L,氨基乙酸0.5 mol/L,H3BO30.6 mol/L,NaH2PO2 H2O 0.3 mol/L,pH=1.5,温度50°C,镀笔移动速率15 cm/s。研究了电压对镀铬层显微结构、表面粗糙度、厚度、显微硬度和耐磨性的影响。随电压增大,镀层厚度增大,显微硬度和耐磨性均先提高后降低。电压为14 V时,镀层的表面平整,粗糙度为2.387μm,显微硬度为602 HV,耐磨性最好。     

Electrophoretic deposition of graphene oxide on carbon brush as bioanode for microbial fuel cell operated with real wastewater

Microbial fuel cell (MFC) is a promising technology for simultaneous wastewater treatment and energy harvesting. The properties of the anode material play a critical role in the performance of the MFC. In this study, graphene oxide was prepared by a modified hummer's method. A thin layer of graphene oxide was incorporated on the carbon brush using an electrophoretic technique. The deoxygenated graphene oxide formed on the surface of the carbon brush (RGO-CB) was investigated as a bio-anode in MFC operated with real wastewater. The performance of the MFC using the RGO-CB was compared with that using plain carbon brush anode (PCB). Results showed that electrophoretic deposition of graphene oxide on the surface of carbon brush significantly enhanced the performance of the MFC, where the power density increased more than 10 times (from 33 mWm^?2 to 381 mWm^?2). Although the COD removal was nearly similar for the two MFCs, i.e., with PCB and RGO-CB; the columbic efficiency significantly increased in the case of RGO-CB anode. The improved performance in the case of the modified electrode was related to the role of the graphene in improving the electron transfer from the microorganism to the anode surface, as confirmed from the electrochemical impedance spectroscopy measurements.     

A highly active composite electrocatalyst Ni–Fe–P–Nb2O5/NF for overall water splitting

This work demonstrates a facile Nb₂O₅-decorated electrocatalyst to prepare cost-effective Ni–Fe–P–Nb₂O₅/NF and compared HER & OER performance in alkaline media. The prepared electrocatalyst presented an outstanding electrocatalytic performance towards hydrogen evolution reaction, which required a quite low overpotential of 39.05 mV at the current density of ?10 mA cm^?2 in 1 M KOH electrolyte. Moreover, the Ni–Fe–P–Nb₂O₅/NF catalyst also has excellent oxygen evolution efficiency, which needs only 322 mV to reach the current density of 50 mA cm^?2. Furthermore, its electrocatalytic performance towards overall water splitting worked as both cathode and anode achieved a quite low potential of 1.56 V (10 mA cm^?2).     

Simplification of the Plasma Load of Negative-Pulse-Bias Source Used in Arc Ion Plating

Based on the voltage and current fluctuating phenomenon in the arc plasma load under the negative-pulse-bias, usingthe plasma physics theory and analysis of computer simulation expatiates that the nature of plasma load in vacuumarc plasma is a capacitance     

陶瓷表面化学镀的前处理工艺新进展

综述了非金属表面化学镀前处理工艺的现状和发展，对陶瓷化学镀的粗化和活化工艺的新进展进行了评述，侧重讨论了离子型、胶体钯型、浆料型、分子自组装吸附钯型、贱金属型活化工艺特点和进展，并展望了今后发展方向。     

Effect of Rare Earth Element Cerium on Mechanical Properties and Morphology of TiN Coating Prepared by Arc Ion Plating

TiN coatings were deposited on polished substrates of W18Cr4V high speed steel by means of vacuum arc ion plating. The effect of cerium on adhesion between TiN coating and substrate was studied. The microstructures and composition of TiN coatings were also investigated by means of scanning electron microscope (SEM), Auger electron spectroscopy (AES), and X-ray diffraction (XRD) technique. It was found that cerium is an effective modifying agent and the addition of suitable amount of cerium to TiN coatings can produce relatively excellent properties such as micro-hardness, wear resistance, oxidation resistance and porosity. The experimental results show that the added cerium in TiN coatings makesa contribution to form the preferred direction along with a (111 ) or (222) close packed face, which may be one of the reasons that improves some properties mentioned above.     

化学镀Ni-P合金/TiO2复合膜的耐蚀性研究

在改进常规制备方法的基础上，提出化学镀/溶胶-凝胶复合法在碳钢表面制备TiO2复合膜的新技术。用衍射研究了复合膜的组织形态，采用环境扫描电镜（ESEM）表征了复合膜的表观和断面形貌，用极化电阻、阳极极化曲线测量等方法研究TiO2复合膜在0.5mol/L硫酸和0.5mol/L氯化钠溶液中的耐蚀性能。结果表明A3钢表面的TiO2复合膜耐蚀性能优良。     

电沉积Ni-W合金镀层的X射线光电子能谱分析

采用X射线光电子能谱（XPS）对电沉积Ni-W合金镀层表面膜进行了分析。研究结果表明，Ni-W合金镀层表面存在一层薄的氧化膜，而钨的氧化作用远大于镍，Ni-W合金镀层中W含量的提高对耐蚀性起决定作用。     

脉冲化学沉积非晶态Ni—P合金原子分布函数研究

采用Ｘ射线衍射分析技术，研究了脉冲化学镀非晶态Ｎｉ－Ｐ合金的原子分布和函数，得出其短程有序原子集团的尺度为０．７５４ｎｍ，约为熔体激冷法获得的非晶态Ｎｉ－Ｐ合金短程有序畴的１／２。并利用脉冲化学沉积非晶态合金的微机制择这一结果进行了解释。     

聚苯胺锂基润滑脂载流润滑下的摩擦学性能

制备了导电聚苯胺锂基润滑脂（简称PANI脂）和铜基银镀层材料（简称银层材料）。采用摩擦磨损试验机考察在无载流、载流及边界润滑条件下，铜基体材料（简称铜基材料）和银层材料的摩擦磨损性能。采用X射线衍射（XRD）、扫描电子显微镜（SEM）和电子能谱（EDS）对银层材料晶相及其表面磨斑形貌进行表征。结果表明，载流条件下，PANI脂润滑试验时的银层材料不仅具有良好的减摩抗磨性能，而且导电能力更强，其优异的减摩和抗磨性能归功于摩擦表面的保护膜和电流热效应引起的表面软化双重作用。