Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

聚丙烯酸酯/醇酸树脂复合乳液的合成与表征

用乳液聚合法合成了聚丙烯酸酯/醇酸树脂复合乳液,研究了醇酸树脂组成和用量及聚合条件对动力学和复合乳液性能的影响。结果表明,醇酸树脂对乳液聚合有明显的阻聚作用,而且这种阻聚作用随醇酸树脂中马来酸酐含量的增加而加剧。升高聚合温度和增加引发剂用量均有利于改善乳液的机械稳定性。随着醇酸树脂用量的增加,复合乳液的机械稳定性和涂膜的耐水性逐渐提高;醇酸树脂中马来酸酐含量增加,乳液机械稳定性提高,当醇酸树脂中马来酸酐质量分数为2 4%时,涂膜具有最佳的耐水性。     

Improvement of the deflocculating power of polyacrylates in ceramic slips by small additions of quaternary ammonium salts

In this work, we examine the effect of small additions of cationic quaternary ammonium salts (QAS) of different molecular weight on the rheology of an industrial ceramic suspension deflocculated with sodium polyacrylate and sodium metasilicate. The observed shear thinning behaviors obey the typical power law of fluid rheology. In order to characterize the rheological behavior of these slurries, three new parameters are introduced: a low shear rate consistency index and two transient viscosities, distant from the equilibrium, after increasing and decreasing the shear rates. These parameters vary with polyacrylate molecular weight and on additions of small quantities of QAS, which we found to be useful for decreasing the slurry viscosity.     

聚氨酯-聚丙烯酸酯共聚乳液的成膜和性能

通过XPS和接触角测试研究了聚氨酯-聚丙烯酸酯共聚乳液在不同基材上的成膜情况，并对共聚胶膜的耐水性和附着力进行了考察．由于该共聚乳液同时存在着亲水组分和疏水组分，所以它在不同的基材上成膜可导致其膜表面的组成成分不同，因而导致其耐水性和附着力也随基材而异。结果表明，亲水性的聚氨酯组分均富集于胶膜内部，但胶膜底层聚氨酯组分的含量却随基材的不同而不同。在憎水且表面张力较高的基材上，共聚胶膜的耐水性良好；共聚胶膜的附着力在表面张力较高的基材上也良好。     

Structure and damping properties of polydimethylsiloxane and polymethacrylate sequential interpenetrating polymer networks

By using the technology of the sequential interpenetrating polymer network, a series of novel damping materials based on a polydimethylsiloxane (PDMS)/polyacrylate (PAC) matrix with polymethacrylate (PMAC) were synthesized. They have a controllable broad transition peak spanning the temperature range of 150–220°C and the medial value of loss factor with maximum of 0.35–0.60. Dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and atomic force microscopy (AFM) were applied to analyze and characterize the transition behavior and the microphase structure of the materials. It was found that the size and height of a transition peak at both the low‐ and the high‐temperature zones change as a function not only of the concentration of PMAC and PDMS but also of the kind of PMAC; simultaneously, the low‐ temperature behavior was also governed by the crystallization of PDMS. The content of the crosslinking agent exerts a significant influence on the configuration of the curves of the transition peaks. AFM shows a characteristic phase morphology of double‐phase continuity containing a transition layer and domain less than 1 μm, indicating that the interwoven multilayer networks are the key to incorporation of the immiscible components and form a broad damping functional region. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 545–551, 2002     

SBS APP复合改性沥青的研究

采用SBS、APP复合改性渣油,可以得到性能优良的改性沥青材料。其最佳配料和共混工艺条件为:SBS/(SBS+APP)之比0.4、外掺量20%、转速1930rPm、共混时间1.0 hr,共混温度20℃。     

Behaviour of mesogenic side group polyacrylates in dilute and semidilute regime

The solution behaviour of a new mesogenic side group polyacrylate in tetrahydrofuran and toluene has been investigated by static and dynamic light scattering. In the dilute regime the polymer behaves as typical polydisperse linear chains in good solvent and the dynamics is dominated by a single fast mode. Cluster formation was detected starting at a concentration around 50 g l⁻¹. It seems to be independent of the solvent as well as of polymer molecular weight. In the semidilute regime, the behaviour of the reduced osmotic modulus leads to the conclusion that repulsion between the chains is stronger than in linear macromolecules. The appearance of larger clusters was revealed above a characteristic concentration and is slightly dependent on the polyacrylate molecular weight. The dynamics was generally characterised by a fast mode related to the cooperative diffusion and by a slow mode associated with large clusters. The existence of a network of multiconnected clusters is envisaged with increasing solution concentration.     

铸造用CO2硬化冷芯盒材料及工艺的发展

铸造用CO2硬化粘结剂系统具有气硬冷芯盒的优点,同时又具有环保方面的优势。主要介绍了水玻璃-CO2法、聚丙烯酸钠-CO2法、酚醛树脂-CO2法三种工艺。这些工艺方法近年来国内外研究较多,并且取得了很大进展。     

聚氨酯/聚丙烯酸酯互穿网络涂料印花粘合剂的制备和应用

本文综述了聚氨酯/聚丙烯酸酯互穿网络(IPN)涂料印花粘合剂。介绍了IPN粘合剂的制备方法及其不同配比时对拉伸强度、断裂伸长率、摩擦牢度性能的影响。IPN粘合剂可克服聚丙烯酸酯粘合剂的延伸性差、湿摩擦牢度低、易吸尘和粘搭性强的缺点,是改进聚丙烯酸酯类粘合剂性能十分有效的方法。