High areal capacitance of FeOOH-carbon nanotube negative electrodes for asymmetric supercapacitors

The relatively low capacitance of negative electrodes, as compared to the capacitance of advanced positive electrodes, poses a serious problem, since this limits the development of asymmetric supercapacitor (SC) devices with a large voltage window and enhanced power-energy characteristics. We fabricate negative SC electrodes with a high capacitance that match the capacitance of advanced positive electrodes at similar active mass loadings, as high as 37?mg?cm^?2. Cyclic voltammetry, impedance spectroscopy, galvanostatic charge-discharge data and the power-energy characteristics of the asymmetric SC device exhibit good electrochemical performance for a voltage window of 1.6?V. Our approach involves the development and application of particle extraction through liquid-liquid interface (PELLI) methods, new extraction mechanisms and efficient extractors to synthesize α-FeOOH and β-FeOOH electrode materials. The use of PELLI allows agglomerate-free processing of powders, which facilitates their efficient mixing with multiwalled carbon nanotubes (MWCNT) and allows improved electrolyte access to the particle surface. Experiments to determine the properties of FeOOH-MWCNT composites provided insight into the influence of the electrode material and the structure of extractor molecules on the composite properties. The highest capacitance of 5.86?F?cm^?2 for negative electrodes and low impedance were achieved using α-FeOOH-MWCNT composites and a 16-phosphonohexadecanoic acid (PHDA) extractor. This extractor allows adsorption on particles, not only at the liquid-liquid interface, but also in the bulk aqueous phase and can potentially be used as a capping agent for particle synthesis and as an extractor in the PELLI method.     

锰铜基高阻尼合金中锌量的测定──硫氰酸盐萃取分离络合滴定法

基于甲基异丁基甲酮于稀盐酸介质中定量地萃取Ｚｎ￣（２＋）与ＣＮＳ￣－形成的络阴离子。从而达到与共存的锰、镍、铝、铬的完全分离。在有氟化物、硫脲存在时Ｆｅ￣（３＋）、Ｃｎ￣（２＋）和Ａｇ￣＋也不被萃取。有机相中的锌于ＰＨ５．５“六胺”缓冲介质中返萃取回水相，用ＥＤＴＡ滴定。在文中给定的条件下锌的一次被萃取率可达９９％以上，成功地解决了锰铜基高阻尼合金中共存离子对锌量测定的干扰问题。     

全球趋向统一的《粉末冶金零件材料规范》

评述了ISO 5 75 5“烧结金属材料—规范”和美国MPIF标准 35的变迁和趋向统一。阐述了“最小强度值”的意义。说明了我国粉末冶金结构零件材料标准的现状     

高Al2O3物料对镍电炉渣粘度的影响

论文对Al2O3高达69．46％的含镍物料电炉处理时对炉渣性能的影响进行了研究。研究表明：吉林镍业公司冶炼厂电炉渣1340℃时黏度为0．538P．s；电炉渣在不添加任何其它试剂的情况下，渣中Al2O3含量不宜高于9％；加入添加剂后，炉渣黏度降低，当在配料中加入20％此种含镍物料时，添加剂加入量7％为宜，此时炉渣黏度为0．74P．s（1340℃）。     

A simple polyol synthesis of silver metal nanopowder of uniform particles

Silver metal has been synthesized in form of a finely divided loose nanopowder, 10–30 nm particle sizes, using a simple polyol process. In hot water, polymer molecules of polyvinyl alcohol (PVA) induce Ag⁺ → Ag reaction as a weak reducer (suitable to control the final particle size), forming a nanofluid of Ag nanoparticles in situ dispersing in part of PVA molecules. Ag nanoparticles do not aggregate much when casting a viscous Ag–PVA nanofluid (hot) onto a substrate in thin laminates or films. Freestanding Ag–PVA films could be obtained of 1–5 mm thickness after drying at room temperature. Dried sample can be easily peeled from a silicate glass substrate. As small as 5–10 mm Ag–PVA pieces were heated in air in order to recollect Ag nanoparticles by burning off the polymer. At 300–400 °C, Ag–PVA disintegrates and encounters combustion in air, resulting in a pure Ag-powder. As analyzed by X-ray diffraction, a single crystalline phase of an Fm3m cubic crystal structure formed. Lattice parameter a = 0.4071 nm and density ρ = 10.61 g/cm³ compare well the bulk values a = 0.4086 nm and ρ = 10.50 g/cm³.     

三聚甲醛萃取—精馏新工艺及过程优化

本文对采用Ｓ１和Ｓ２的混合物作为萃取剂的三聚甲醛萃取－精馏新工艺进行了模拟计算，得到了使总费用最低的三聚甲醛精制工艺的联合操作参数。模拟计算结果成功地指导了小试操作，并可为大型工程设计提供可靠的基础数据。     

测定环境中钚的新方法

提出了ＴＯＰＯ萃取，大面积有机相制原与平行板屏栅电离室α谱仪结合，测定草、土壤等环境中钚的新方法。土壤和草灰的化学回收率分别为７２％和９７％，最低探测限为４×１０＾－２Ｂｑ／ｋｇ。分析了Ｉ－ＡＥＡ和ＮＩＳＴ的标准物质，结果与标准值相符。操作程序简单、快速，适用于核事故应急分析和环境监测。