An improved feedrate scheduling method for NURBS interpolation in five-axis machining

Five-axis machining plays an important role in manufacturing by dint of its high efficiency and accuracy. While two rotation axes benefit the flexibility of machining, it also brings limitations and challenges. In order to further balance machining precision and efficiency, an improved feedrate scheduling method is presented considering geometric error and kinematic constraints for the Non Uniform Rational B-Spline (NURBS) interpolation in five-axis machining. A simplification method is proposed to calculate the geometric error which describes the deviation between the ideal tool path and the real tool path induced by the non-linear movement. A linear relation between geometric error and feedrate is built to limit the feedrate. The constraints determined by single axis kinematic performance and tangential kinematic performance are also considered. Under these constraints, a constrained feedrate profile is determined. Aiming to get more constant feedrate in the difficult-to-machine areas, this work proposes a scheduling method which combines morphological filtering and S-shape acceleration/deceleration (acc/dec) mode. Simulations and experiments are performed to compare the proposed feedrate scheduling method with two previous feedrate scheduling method and the results prove that the proposed feedrate scheduling method is reliable and effective.     

Multi-discharge EDM coring of single crystal SiC ingot by electrostatic induction feeding method

A new technique of EDM coring of single crystal silicon carbide (SiC) ingot was proposed in this paper. Currently single crystal SiC devices are still of high cost due to the high cost of bulk crystal SiC material and the difficulty in the fabrication process of SiC. In the manufacturing process of SiC ingot/wafer, localized cracks or defects occasionally occur due to thermal or mechanical causes resulted from fabrication processes which may waste the whole piece of material. To save the part of ingot without defects and maximize the material utilization, the authors proposed EDM coring method to cut out a no defect ingot from a larger diameter ingot which has localized defects. A special experimental setup was developed for EDM coring of SiC ingot in this study and its feasibility and machining performance were investigated. Meanwhile, in order to improve the machining rate, a novel multi-discharge EDM coring method by electrostatic induction feeding was established, which can realize multiple discharges in single pulse duration. Experimental results make it clear that EDM coring of SiC ingot can be carried out stably using the developed experimental setup. Taking advantage of the newly developed multi-discharge EDM method, both the machining speed and surface integrity can be improved.     

Liner services network design and fleet deployment with empty container repositioning

Transportation demand of shipping container fluctuates due to the seasonality of international trade, thus, every 3–6 months, the liner company has to alter its current liner shipping service network, redeploy ships and design cargo routes with the objective of minimizing the total cost. To solve the problem, the paper presents a mixed integer linear program model. The proposed model incorporates several relevant constraints, such as weekly frequency, the transshipment of cargo between two or more service routes, and transport time. Extensive numerical experiments based on realistic date of Asia–Europe–Oceania shipping operations show that the proposed model can solve real-case problems efficiently by CPLEX. The results demonstrate that the model can reduce ship’s capacity consumption and raise ships’ capacity utilization.     

嵌入式实时操作系统内核混合代码的自动化验证框架

"如何构造高可信的软件系统"已成为学术界和工业界的研究热点.操作系统内核作为软件系统的基础组件，它的安全可靠是构造高可信软件系统的重要环节.为了确保操作系统内核的安全可靠，将形式化方法引入到操作系统内核验证中，提出了一个自动化验证操作系统内核的框架.该验证框架包括：（1）分别对C语言程序和混合语言程序（C语言和汇编语言）进行验证；（2）在混合语言程序验证中，为汇编程序建立抽象模型，并将C语言程序和抽象模型粘合形成基于C语言验证工具可接收的验证模型；（3）从规范中提取性质，基于该自动验证工具，对性质完成自动验证；（4）该框架不限于特定的硬件架构.成功地运用该验证框架对两种不同硬件平台的嵌入式实时操作系统内核μC/OS-II进行了验证.结果显示：利用该框架在对两个不同的硬件平台上内核验证时，框架的可重复利用率很高，高达到88%，虽然其抽象模型需要根据不同的硬件平台进行重构.在对基于这两种平台的操作系统内核验证中，分别发现了10~12处缺陷.其中，在ARM平台上两处与硬件相关的问题被发现.实验表明，该方法对不同硬件平台的同一个操作系统分析验证具有一定的通用性.     

菌型叶根动叶片叶根叶冠内径向的加工

菌型叶根动叶片是一种新型的动叶片,采用数控铣加工叶根内径向面时留0.1~0.2mm余量,然后在进行叶根内径向磨削,叶冠直接加工到位,没有后序磨削加工,由于叶根叶冠在加工过程中不是一次装夹完成的,根冠存在一定的落差,在后续的装配中容易产生配合间隙,无法达到要求。文中介绍了一种新的加工工艺,解决了这一问题。     

Abrasive waterjet micro-machining of channels in metals: Comparison between machining in air and submerged in water

Abrasive water jet technology can be used for micro-milling using recently developed miniaturized nozzles. Abrasive water jet (AWJ) machining is often used with both the nozzle tip and workpiece submerged in water to reduce noise and contain debris. This paper compares the performance of submerged and unsubmerged abrasive water jet micro-milling of channels in 316L stainless steel and 6061-T6 aluminum at various nozzle angles and standoff distances. The effect of submergence on the diameter and effective footprint of AWJ erosion footprints was measured and compared. It was found that the centerline erosion rate decreased with channel depth due to the spreading of the jet as the effective standoff distance increased, and because of the growing effect of stagnation as the channel became deeper. The erosive jet spread over a larger effective footprint in air than in water, since particles on the jet periphery were slowed much more quickly in water due to increased drag. As a result, the width of a channel machined in air was wider than that in water. Moreover, it was observed that the instantaneous erosion rate decreased with channel depth, and that this decrease was a function only of the channel cross-sectional geometry, being independent of the type of metal, the jet angle, the standoff distance, and regardless of whether the jet was submerged or in air, in either the forward or backward directions. It is shown that submerged AWJM results in narrower features than those produced while machining in air, without a decrease in centerline etch rate.     

航空发动机复杂扭曲叶片分步电解加工研究

为实现复杂扭曲叶片在较小间隙下的稳定加工,提出了一种分步式电解加工的工艺方法,建立了复杂扭曲叶片小间隙(0.2 mm)和大间隙下(0.5 mm)扭曲流道的流道模型,采用有限元法进行了流场仿真研究,结果表明增加流道间隙可以解决流道中涡流和流场紊乱的问题。开展了复杂扭曲叶片小间隙连续式加工和分步式加工的试验研究。结果表明,采用小间隙连续式加工,当阴极进给至3.8 mm位置时,在叶片排气边靠近叶根流道扭曲处出现短路打火情况;而采用分步式加工方式能够实现加工的顺利进行。     

Electromagnetism-like algorithms for optimized tool path planning in 5-axis flank machining

Optimization of tool path planning using metaheuristic algorithms such as ant colony systems (ACS) and particle swarm optimization (PSO) provides a feasible approach to reduce geometrical machining errors in 5-axis flank machining of ruled surfaces. The optimal solutions of these algorithms exhibit an unsatisfactory quality in a high-dimensional search space. In this study, various algorithms derived from the electromagnetism-like mechanism (EM) were applied. The test results of representative surfaces showed that all EM-based methods yield more effective optimal solutions than does PSO, despite a longer search time. A new EM-MSS (electromagnetism-like mechanism with move solution screening) algorithm produces the most favorable results by ensuring the continuous improvement of new searches. Incorporating an SPSA (simultaneous perturbation stochastic approximation) technique further improves the search results with effective initial solutions. This work enhances the practical values of tool path planning by providing a satisfactory machining quality.     

一种大型复杂构件加工新模式及新装备探讨

大型复杂构件是航空航天、能源、船舶等领域装备的核心结构件，此类构件通常具有尺寸大、形状复杂、刚性弱等特点。传统“分体离线加工-在线检测”模式存在工艺不稳定、过程复杂、柔性差、周期长等问题，以龙门式多轴数控机床加工为代表的“包容式”加工模式，难以适应大型复杂构件的高效高质量加工制造需求。提出一种基于移动式和吸附式机器人的多机协同原位加工新模式，通过多机器人系统自主寻位、精确定位加工与加工质量原位检测，实现大型复杂构件多安装面并行铣削、制孔与打磨等作业。多机器人系统包括移动式混联机器人、吸附式并联机器人、移动式串联铣削机器人、移动式双臂加工机器人和移动式打磨机器人。构建多机协同原位加工模式，需要揭示多机器人协同原位加工行为与大型弱刚性结构件质量控制的交互机理，面临着本体、测量、工艺和集成四个方面的挑战，需要设计高灵活、高刚度的移动式和吸附式加工机器人，解决移动机器人自主准确寻位和超大结构件原位高精检测难题，攻克加工变形误差在线补偿和振动抑制技术，通过集成实现多机协同高效高精加工，为大型复杂构件的高效高质量制造提供创新技术及装备，并实现此类构件制造核心技术及装备自主可控。     

Prediction Model for BTA Deep-Hole Machining using Fuzzy Clustering Approach: Experimental Study

In this article, a subtractive clustering-based fuzzy identification method and a Sugeno-type fuzzy inference system are used for modeling in metal cutting. This approach is considered with its application on the experimental study of Boring and Trepanning Association (BTA) deep-hole drilling. The model for the surface roughness is identified by using the cutting speed and feed as input data and roughness as the output data. Using subtractive clustering in both input and output spaces performs the model-building process. Minimum error model is obtained through enumerative search of clustering parameters. The fuzzy model obtained is capable of predicting the surface roughness for a given set of inputs (speed and feed). Therefore, the operator can predict the quality of the surface for a given set of working parameters and will then be able to set the machining parameters to achieve a certain surface quality. The fuzzy model is verified experimentally by further experimentation using different sets of inputs. The tool life is also investigated using the same approach. The fuzzy inference system obtained is capable of predicting the tool life for a given set of cutting parameters. Therefore, the operator will be able to predict how many minutes the cutting tool is going to last and will set the time for the next tool change.