Changes in the physical properties of honey powder during storage

Honey powders produced by spray drying with the addition of Arabic gum and sodium caseinate were characterised in terms of the influence of storage time on the following physical properties: particle size, moisture content, water activity, bulk density, flowability and hygroscopicity. The storage affected those properties; after 12 weeks of storage, particle size decreased (except Arabic gum powder treated as a control sample), moisture content and water activity increased, hygroscopicity decreased. Changes in bulk density, particle size and moisture content caused the rise of Hausner ratio value; however, the powders were still characterised by a very good flow properties and low cohesiveness. The colour of reconstituted powders was also affected by storage; in most of samples, the darkening, reduction in redness and yellowness were observed. Colour parameters were the most stable in powders obtained with the addition of 2% w/w of sodium caseinate.     

二氧化碳气体保护焊在厚板上的应用

板厚为 5 5mm的 16Mn钢采用CO2 半自动气保焊建造大型转炉炉体的可能性和可靠性如何 ?目前尚缺少足够的试验数据。为了给转炉工程的施工焊接提供可靠数据 ,确保焊接质量 ,对板厚 5 5mm16Mn钢CO2 半自动的焊接性能进行了一系列的试验研究     

NSA-500-1型氩弧焊机VD9不同接法对引弧和稳弧的影响

从一起NSA－500－1型氩弧焊机故障，分析其高压脉冲旁路二极管VD9不同接法对引弧、稳弧及设备安全的影响。     

Improving Wear Resistance of the Ni-base Thermal Spray-Welding Coating Using Rare Earths

ＩｍｐｒｏｖｉｎｇＷｅａｒＲｅｓｉｓｔａｎｃｅｏｆｔｈｅＮｉｂａｓｅＴｈｅｒｍａｌＳｐｒａｙＷｅｌｄｉｎｇＣｏａｔｉｎｇＵｓｉｎｇＲａｒｅＥａｒｔｈｓＺｈａｉＧｕａｎｇｊｉｅ（翟光杰）（ＩｎｓｔｉｔｕｔｅｏｆＰｈｙｓｉｃｓ，ＡｃａｄｅｍｉｃａＳｉ...     

一种洁净的、非接触性的新型粘合剂喷洒技术

介绍了Robatech公司开发的PFC喷嘴。这种喷嘴为标准化组件，具有较大的适用性，既适用于新厂配套，也适用于老设备改造。     

45钢表面超音速电弧喷涂Ti-Al涂层的组织与性能研究

采用自行开发研制的超音速电弧喷设备，在45钢表面制成了钛铝合金复合涂层。并利用金相显微镜、X射线衍射仪、扫描电镜、电子探针，对涂层的成分、相结构、显微组织及其结合强度、显微硬度进行了研究。结果表明，利用超音速电弧喷涂设备，可以在45钢表面形成 度高、孔隙率低，结合强度较好和硬度高的Ti-Al合金涂层。     

Microstructures formed by spray freezing of food fats

The spray-freezing of two food fats, tripalmitin (PPP) and cocoa butter (CB) and mixtures thereof, has been modeled experimentally using a novel single droplet freezing apparatus configured so that temperature profiles or samples for microstructure analysis can be obtained. For 2 mm diameter droplets suspended in a cold air flow at temperatures around 2–15°C, initial cooling rates were on the order of 10 K s⁻¹ and the temperature profiles could be correlated directly to DSC data collected at 20 K min⁻¹, indicating that minimal supercooling of the materials occurred in the droplet form. Microstructure analysis confirmed that PPP crystallized preferentially in mixtures, and that the surface structure was very sensitive to storage conditions. The bulk structure was much less sensitive, and the internal microstructure of the PPP droplets revealed distinct nucleation sites, which were absent from the CB: These persisted in the mixtures up to 50 wt%. X-ray analysis indicated that the fats crystallized in their more stable forms, namely, β for PPP and Form V/V1 in CB.     

IF板与08Al板的成形性能研究

通过模拟成形性试验，对新型超深冲用IF钢板和传统冲压用08Al钢板的冲压成形性能进行了研究．结果表明：IF板的拉深性能、扩孔性能、胀形性能以及“拉深-胀形”复合性能等均优于08Al板，其中，扩孔性能和平面各向异性的改善最为显著；各项试验中，IF板的成形力普遍小于08Al板。     

Effect of Rare Earth Element Cerium on Mechanical Properties and Morphology of TiN Coating Prepared by Arc Ion Plating

TiN coatings were deposited on polished substrates of W18Cr4V high speed steel by means of vacuum arc ion plating. The effect of cerium on adhesion between TiN coating and substrate was studied. The microstructures and composition of TiN coatings were also investigated by means of scanning electron microscope (SEM), Auger electron spectroscopy (AES), and X-ray diffraction (XRD) technique. It was found that cerium is an effective modifying agent and the addition of suitable amount of cerium to TiN coatings can produce relatively excellent properties such as micro-hardness, wear resistance, oxidation resistance and porosity. The experimental results show that the added cerium in TiN coatings makesa contribution to form the preferred direction along with a (111 ) or (222) close packed face, which may be one of the reasons that improves some properties mentioned above.     

变形温度和变形程度对Ti－31合金性能和组织的影响

通过高温和室温拉伸试验，研究了变形温度和变形程度对Ｔｉ－３１合金板材性能和组织的影响。结果表明，合金在７５０～８５０℃的温度下变形５％～２０％空冷后，其室温机械性能均能达到材料的技术指标要求。并发现了材料在９００℃的临界变形区。