潜孔锤冲击作用下土体变形的有限元分析

潜孔锤冲击挤密钻进过程中周围土体的变形机理是一个高度非线性问题。针对潜孔锤在土中的面-面接触问题,运用Drucker-Prager屈服准则为判据,将土体视为DP材料,通过钻具与土之间的接触及施加冲击载荷来模拟钻进过程,从而建立了潜孔锤在土中冲击挤密钻进的有限元模型。利用非线性瞬态动力学有限元分析手段,对钻进过程中冲击力对土的作用加以研究,分析了钻具周围土体的应力、应变以及钻具与土体的摩擦情况。结果表明,在冲击载荷作用下,锥形钻头前端土体应力集中,并形成应力泡,冲击功主要用于竖向压缩土体,而水平方向的挤压作用相对较小,摩擦应力在钻头锥面附近出现峰值,是影响钻进速度的主要原因之一。     

镁合金材料的应用及其加工技术的发展(1)

第一部分较全面地介绍镁及镁合金材料在交通运输、航空航天、电子工业、核能工业、化工、冶金等部门的应用方向与实例。第二部分简要地论述镁合金材料的加工技术，重点介绍镁合金新材料的研发、熔炼铸造工艺、压铸成型工艺、挤压技术、锻压技术与轧制技术的进展。指出镁合金是一种很有发展前景的新型金属材料，其加工技术将获得进一步的快速发展。     

Effects of temperature and blank holding force on biaxial forming behavior of aluminum sheet alloys

Biaxial forming behavior is investigated for three aluminum sheet alloys (Al 5182 containing 1% Mn (5182+Mn), Al 5754, and 6111-T4) using a heated die and punch in the warm forming temperature range of 200–350 °C. It is found that, while all three alloys exhibit significant improvement in their formability compared with that at room temperature, the non-heat-treatable alloys 5182 + Mn and 5754 give higher part depths than that of heat-treatable 6111-T4. The formability generally increases with decreasing BHP (BHP), but increasing the forming temperature and/or BHP minimizes the wrinkling tendency and improves the forming performance. The stretchability of the sheet alloys increase with increasing temperature and increasing BHP. For the alloys and forming conditions involved in the current study, the formability, measured in terms of part depth, comes mainly from the drawing of metal into the die cavity, although stretching effects do influence the overall forming behavior. The optimum formability is achieved by setting the die temperature 50 °C higher than the punch temperature to enhance the drawing component. Setting the die temperature higher than the punch temperature also improves the strain distribution in a part in such a manner that postpones necking and fracture by altering the location of greatest thinning.     

新型吸-放热复合发泡剂的特性分析与应用

对自制的新型吸－放热复合发泡剂ＨＣＢ－ＮＸ的分解动力学和热力学特性进行了研究,同时对采用该发泡剂进行硬质聚氯乙烯低发泡挤出的特性及泡孔结构进行了分析。     

热塑性淀粉／聚己内酯共混物的制备和性能的初步研究

利用热塑性淀粉（TPS）与聚己内酯（PCL）熔融共混并挤出可用来制备完全可生物降解的塑料，研究表明，组分PCL以及增塑剂水和甘油的含量对体系的力学性能和耐水性有显著的影响。     

Corner forming of AZ61A magnesium alloy tube within warm hydroforming

The corners with small radii on cross sections are crucial for forming hydroformed components with polygonal sections.In this paper,warm hydroforming experiments of AZ61A magnesium alloy tubes were carried out to study the forming regularity of round corners by using a demonstration part with square sections.Effects of temperature on radius forming,thinning ratio distribution and microstructure were revealed and a component with relative outer corner radius of 3.0 was obtained by warm hydroforming at 240℃.The minimum thickness of the formed square section was located in the transition position between the corner and the straight wall.The thinning ratio of the round corner increased with the increase of forming temperature.Formability of the magnesium tube was improved by raising temperature under the effect of dynamic recrystallization at 240℃.     

面板堆石坝面板顺坡向挤压破坏机理的试验研究

本文针对面板堆石坝面板顺坡向挤压破坏的钢筋压曲凸起问题开展了试验研究,采用了配有单根立筋的混凝土柱受压试验来模拟面板顺坡向的挤压破坏。试验结果证实了以往研究中无箍筋钢筋混凝土立柱抗压强度低于素混凝土柱、且钢筋保护层厚度越小强度越低的推测。与素混凝土柱相比,保护层厚5 cm钢筋混凝土柱的强度降低约10％。根据试验的破坏荷载结果,通过已有理论解反推出了立柱的侧向支撑刚度k,对于保护层厚5 cm和8 cm立柱k值相应为0.841 N·mm^-2和1.032 N·mm^-2。经过试验结果分析,发现钢筋混凝土立柱各截面不服从应变平面假设,受压中钢筋没有同混凝土一起协调变形,钢筋与混凝土之间相互作用强烈。本研究结果再次说明,限制钢筋的侧向变形是防止面板顺坡向挤压破坏的根本措施。应开展可模拟混凝土中钢筋压曲的挤压破坏数值模拟研究,为这些措施的量化设计提供依据。     

Effect of sintering parameters on warm compacted iron-based material

1　INTRODUCTIONItiswellknownthatincreasingdensityisthebestwaytoincreasetheperformanceofpowdermet allurgy(P/M ) parts.ConventionalP/Mprocessingcanproduceiron basedpartswithdensitylessthan 7.1g/cm3(arelativedensityof 90 %approximately) .Theirmechanicalpropertiesaresubstantiallylessthanthoseoftheirfulldensitycounterpart .TherearemanymethodsthatcanproduceP/M partswithrela tivelyhighdensitysuchaswarmcompaction ,hightemperaturesintering ,doublepress/doublesinteringandforging .Warmcompactioni…     

摩托车超越离合器本体的精密锻造工艺研究

通过中间预制坯形状和尺寸的合理设计、采用合适的冷挤压模具结构,用温/冷复合成形工艺进行了摩托车超越离合器本体内孔型腔的精密成形.采用该工艺生产的超越离合器本体精锻件,其内孔型腔不仅表面光洁度高、尺寸精度高,而且内孔型腔不再后续机械加工就可以达到超越离合器本体的设计要求,因此具有显著的节能、节材效果,经济效益十分显著.从1996年至今500万余件的生产实践表明,采用冷/温复合成形工艺是生产摩托车超越离合器本体的一种高效加工工艺.     

锰对5056合金热挤压管材组织性能的影响

研究锰含量对5056铝合金热挤压状态管材组织和力学性能的影响。结果表明，由于5056合金中锰元素的含量少，对再结晶的抑制作用弱，使得挤出的管材组织发生了完生再结晶，从而使其力学性能与退火状态的基本相同，这就为在冷加工时，充分发挥合金的塑性，减少加工道次和退火次数，合理制定冷加工工艺提供了依据。