全尾砂和废石联合胶结充填体最佳配比及应用

针对红岭铅锌矿分级充填骨料来源不足、地表废石堆积污染环境的情况,提出将该矿选厂产生的全尾砂和地表废石作为充填骨料的联合胶结充填方案。分别测试了全尾砂和地表废石的物理化学性质,验证了碎石和全尾砂作为联合充填骨料的可行性。通过充填配比试验,分析了不同配比全尾砂废石充填体强度特性,得出了最佳充填配比。结果表明,充填试块的强度随灰砂比减小而减小,随养护龄期增加呈增大趋势,随充填料浆质量浓度增大而增大,最佳配比为: 胶结充填灰砂比1∶8、普通充填灰砂比1∶12,全尾砂∶废石配比4∶6,质量浓度78%。根据研究结果,在红岭铅锌矿进行了全尾砂废石充填技术工业应用,证实该技术可行。     

Seismic behavior of geosynthetic-reinforced retaining walls backfilled with cohesive soil

This study investigates the seismic performance of geosynthetic-reinforced modular block retaining walls backfilled with cohesive, fine grained clay-sand soil mixture. Shaking table tests were performed for three ½ scaled (wall height 190 cm) and ¼ scaled model walls to investigate the effects of backfill type, the influence of reinforcement length and reinforcement stiffness effects. The El Centro and Kobe earthquake records of varying amplitudes were used as base acceleration. Displacement of the front wall, accelerations at different locations, strains on the reinforcements, and the visual observations of the facing and the backfill surface were used to evaluate the seismic performance of model walls. The model walls were subjected to rigorous shaking and the walls did not exhibit any stability problems or signs of impending failure. The maximum deformations observed on the models with cohesive backfill was less than half of the deformation of the sand model. The load transfers between the geogrid and cohesive soil was comparable to that of sand and hence the needed reinforcement length was similar as well. As a result; the model walls with cohesive backfills performed within acceptable limits under seismic loading conditions when compared with granular backfilled counterparts.     

基于P波模量的原位胶结充填体强度预测模型研究

原位胶结充填体质量评价通常采用单轴抗压强度作为表征指标,由于在现场工程中无法快速、准确获取充填体的强度值,因此需要建立一种参数易于获取且准确的原位胶结充填体强度预测模型。基于胶结充填体物理力学参数的内在联系,从量纲平衡的角度探索了胶结充填体单轴抗压强度与P波模量的关系。根据C矿和I矿两种原位胶结充填体的密度、P波速度及取芯强度的测试数据,采用线性拟合的方法获得了基于P波模量的原位胶结充填体强度预测模型。通过对C矿和I矿的强度预测模型拟合效果分析可知,P波模量与取芯强度呈正相关性,且拟合效果较好,证明原位胶结充填体强度预测模型精度高,具有很强的实用性。     

三峡电源电站厂房尾水肘管混凝土施工技术

在三峡电源电站尾水肘管施工中，采用了肘管平段回填自密实混凝土和充气拔管回填灌浆的方法，施工质量较好。     

云南麻栗坝水库输水隧洞坍塌处理

麻栗坝水库输水隧洞是在高含水量低胶结度的砂砾石为主的土体中开挖的大断面水工隧洞，施工存在极大的风险性。在成洞坍塌处理中采用内外结合、先回填后固结的处理措施，有效地解决了坍塌问题，使该隧洞的掘进能够顺利进行，建成运行表明所采用的方法是适宜的。     

坚持科技创新 打造强势企业

介绍了株洲硬质合金集团有限公司推进科技创新的具体做法,取得的主要成绩,以及今后的努力方向。     

WC15Ni磁合金的质量控制

在WC15Ni无磁硬质合金生产过程中,选用粒度分布范围较窄的优质WC以及添加适量的Cr3C2,促进了抗弯强度的提高。     

稀土元素对硬质合金高温性能的影响

采用动态热模拟试验技术，研究了添加微量稀土元素对硬质含金高温性能的影响。试验结果表明：添加微量稀土元素，能改善硬质合金高温性能，增加合金的塑性和高温韧性，降低硬质合金的热强性。     

Stability control of gob-side entry retained under the gob with close distance coal seams

In multi-seam mining, the interlayer rock strata between the upper coal seam(UCS) and the lower coal seam(LCS) appear damage and strength weakening after mining the UCS. Ground stability control of the gob-side entry retaining(GER) under the gob with close distance coal seams(CDCS) is faced with difficulties due to little attention to GER under this condition. This paper focuses on surrounding rock stability control and technical parameters design for GER under the gob with CDCS. The floor rock strata damage characteristics after mining the UCS is first evaluated and the damage factor of the interlayer rock strata below the UCS is also determined. Then, a structural mechanics model of GER surrounding rock is set up to obtain the main design parameters of the side-roadway backfill body(SBB) including the maximum and minimum SBB width calculation formula. The optimal SBB width and the water-to-cement ratio of high water quick-setting material(HWQM) to construct the SBB are determined as 1.2 m and 1.5:1.0,respectively. Finally, engineering trial tests of GER are successfully carried out at #5210 track transportation roadway of Xingwu Colliery. Research results can guide GER design under similar mining and geological conditions.     

低成本钢尾渣-矿渣基矿山充填料的优化开发

 为实现多固废协同利用、降低充填成本,在矿渣基全粒级细尾砂胶结充填料基础上,以流动性和抗压强度为表征,利用热闷钢渣磁选尾渣(钢尾渣)替代部分矿渣作为胶凝材料,脱硫灰和水泥熟料替代部分专用添加剂作为外加剂,采用正交试验探寻掺量规律,优化固体填充料配比,开发钢尾渣-矿渣基软性矿山充填料,并研究了外加剂与胶材比、灰砂比等因素的影响。对比分析了矿渣基准组、钢尾渣-矿渣基准组(B1)、强度最优外加剂组分钢尾渣-矿渣组(B7)等3组充填料的微观形貌及XRD图谱以探究其水化机理。结果表明,钢尾渣替代矿渣量增加、外加剂与胶材比减小,充填料浆流动性改善,但充填体抗压强度下降。强度正交试验结果表明,钢尾渣掺量大小决定强度低高,脱硫灰掺量宜高于水泥熟料。进一步调整外加剂组分配比,在灰砂比为1∶6、钢尾渣替代矿渣为20%条件下,找出B7组外加剂组分为脱硫灰、水泥熟料分别替代30%、20%专用添加剂,B7组料浆扩展度为143 mm,充填体形貌为富铁绿泥石胶结假方体钙硅灰石,28 d抗压强度达2.13 MPa,较基准组低0.19 MPa,较B1提高0.26 MPa。该替代方案满足现场充填C2级强度的要求,改善流动性并显著降低了充填成本。优化的外加剂组分配比在灰砂比为1∶4条件下同样具有强度优化作用,但较灰砂比为1∶6条件下低。