停棒子系统与控制棒组操作范围监测试验

本文叙述了反应堆保护系统停棒与汽轮机降功率子系统的系统功能、保护参数和秦山核电站控制棒组插入监测器的设计与参数选择,确定了控制棒提升上极限值和在不同工况下棒插入低位、低-低位整定值,并在热态零功率条件下加以验证。试验证明参数选择是合理的,为功率运行阶段提供了数据。     

对水轮机自动调速器油压控制电路的改进

YT－1000型油压自动调速器在运行中不能维持正常油压、在不增加任何设备的情况下，只改动二次接线的处理方法，就能消除隐患、解决问题。     

汽轮机轴承烧瓦与轴颈的渗巴氏合金现象

简述轴承工作性质，巴氏合金应用与相组成的基本情况。论述汽轮机转子在两个电厂长期运行后，由于轴颈发生的不正常摩擦损伤，在大修改造中由无损检查、机械加工揭示出轴颈存在严重的渗巴氏合金现象，低熔点金属Sn、Sb与Cu向转子材料晶界的深层渗入最终导致了3根大型在投转子的严重开裂与报废。图11表2     

工业汽轮机的清洗

本文介绍了用饱和蒸汽对冷凝式汽轮机进行清洗除垢时主要参数的确定、操作要点及清洗方案，清洗后的汽轮机运行正常。     

引进型国产300MW汽轮机窜轴事故分析及防止对策

通过引进型国产300MW汽轮机在启动试运中出现的一次窜轴事故,根据计算机追忆打印的有关图表、数据分析了产生事故的原因,并提出了为防止类似事故重演应采取的措施和建议。经采取措施后该机组多次又在相同情况下启机,已安全运行。说明分析正确,措施得当,值得同类型机组借鉴。     

灯泡贯流式机组发电机冷却装置技术改造方式的探讨

灯泡贯流式发电机组直径小,转速低,发电机的通风冷却是一个难点。通过对京南、马骝滩、石面坦及南津渡等水电站的发电机运行过程中出现的温升过高,定子线棒绝缘受损等问题的分析,提出了解决的措施与改进方案,并对灯泡贯流式机组冷却系统的设计提出了建议,可供参考和借鉴。     

Experimental and computational analysis on guide vane losses of impulse turbine for wave energy conversion

This paper deals with the detailed flow analysis of impulse turbine with experimental and computed results for wave energy power conversion. Initially, several turbulence models have been used in two-dimensional (2-D) computational fluid dynamic (CFD) analysis to find a suitable model for this kind of slow speed unconventional turbine. Experiments have been conducted to validate the CFD results and also to analyze the aerodynamics at various stations of the turbine. The three-dimensional (3-D) CFD model with tip clearance has been generated to predict the internal flow and to understand the effect of tip clearance leakage flow on behavior of the turbine in design and off-design conditions. As a result, it is found from the 2-D results that the comparison between computed and experimental data is good, qualitatively and the turbulence model, standard k–ε can predict the experimental values reasonably well, especially the efficiency of the turbine. Experimental results reveal that the downstream guide vanes are more responsible for low efficiency of the turbine and it is measured that 21% average pressure is lost due to downstream guide vanes. It is proved from the 3-D CFD model with tip clearance that it can predict the experimental values quantitatively and qualitatively. Furthermore, it is estimated from the computed results that the efficiency of the turbine has been reduced about 4%, due to tip clearance leakage flow at higher flow coefficients.     

Simulation Method of Dynamic Characteristics of Turbine Flow Sensor

Computational Fluid Dynamics (CFD) simulation is one of the important methods to study the performance and in-fluencing factors of turbine flow sensors. According to the working characteristics of the turbine flow sensor, the passive simulation method based on the six degrees of freedom (6-DOF) model and dynamic mesh is proposed in this paper. The reliability of the simulation method is verified by steady-state experiments and unsteady-state experiments. The results show that the trend of meter factor with flow rate acquired from the simulation is close to the experimental results, and the deviation between the simulation result and the experiment result is low with a maximum deviation of 2.88%. In the unsteady simulation study, the impeller speed changes with the inlet velocity of the turbine flow sensor, which has a good follow-up. The passive simulation method can be used to predict the dynamic performance of the turbine flow sensor.     

烟气轮机运行中动平衡破坏的原因分析及维护措施

对引发烟气轮机动平衡破坏的原因进行分析 ,并举例加以说明 ,进而提出了烟气轮机平稳运行的维护措施