基于跨临界CO2热泵的茶叶生产能源系统负荷削减潜力

乡村产业中的化石能源设备逐渐被电能技术替代，引起了乡村负荷波动增大、部分时段产生集中高负荷的问题。为了解决以上问题，将低品位清洁能源应用至乡村的茶叶生产中，针对烘茶全过程的工艺要求提出了跨临界CO₂热泵烘茶技术；并以某茶叶生产乡村为对象，对其代表台区的全年日用电量及产茶日负荷进行了分析，得出采用CO₂热泵烘茶后其负荷得到大幅度削减，整体可降低至原负荷的39.6%~46.8%，峰值负荷与平时负荷的比值由原本的13.6降至5.4~6.2。跨临界CO₂热泵应用至农产品生产中可有效缓解乡村供电压力。     

Mass transfer in polycrystalline ytterbium monosilicate under oxygen potential gradients at high temperatures

Mass transfer in polycrystalline Yb₂SiO₅ wafers with precise composition control was evaluated and analyzed by oxygen permeation experiments at high temperatures using an oxygen tracer. Oxygen permeation proceeded due to mutual grain boundary diffusion of oxide ions and Yb ions without synergistic effects such as acceleration or suppression. The oxygen shielding properties of Yb₂SiO₅ were compared with those of the other line compounds such as Yb₂Si₂O₇ and Al₂O₃ based on the determined mass transfer parameters. It was found that the more preferentially an oxide ion diffuses in the grain boundary compared to the interior of the grain, the greater the effect of suppressing the movement of the oxide ion by applying an oxygen potential gradient becomes.     

河南渑池地区铝土矿工艺矿物学及锂的赋存状态研究

通过河南省渑池地区含锂铝土矿(岩)层工艺矿物学分析,查明铝土矿的物质组成、嵌布特征、伴生锂分布特征和赋存状态,为矿产综合利用提供理论依据。结果显示:该铝土矿Al2O3含量为54.8%,铝硅比值(A/S)为2.6,铝土矿层和粘土岩层中Li2O含量均高于伴生锂边界品位,粘土岩中锂更为富集；矿物组成除一水硬铝石之外,主要是以集合体形态产出的粘土矿物。采用稀酸解析、选矿测试和电子探针分析锂的赋存状态,查明矿石中锂主要是以类质同象置换形式赋存在伊利石和高岭石等粘土矿物中；选矿富锂尾矿中Li2O可富集到0.57%左右,是锂综合回收利用的重点研究对象。      

Revealing Electrical-Poling-Induced Polarization Potential in Hybrid Perovskite Photodetectors

Despite recent rapid advances in metal halide perovskites for use in optoelectronics, the fundamental understanding of the electrical-poling-induced ion migration, accounting for many unusual attributes and thus performance in perovskite-based devices, remain comparatively elusive. Herein, the electrical-poling-promoted polarization potential is reported for rendering hybrid organic–inorganic perovskite photodetectors with high photocurrent and fast response time, displaying a tenfold enhancement in the photocurrent and a twofold decrease in the response time after an external electric field poling. First, a robust meniscus-assisted solution-printing strategy is employed to facilitate the oriented perovskite crystals over a large area. Subsequently, the electrical poling invokes the ion migration within perovskite crystals, thus inducing a polarization potential, as substantiated by the surface potential change assessed by Kelvin probe force microscopy. Such electrical-poling-induced polarization potential is responsible for the markedly enhanced photocurrent and largely shortened response time. This work presents new insights into the electrical-poling-triggered ion migration and, in turn, polarization potential as well as into the implication of the latter for optoelectronic devices with greater performance. As such, the utilization of ion-migration-produced polarization potential may represent an important endeavor toward a wide range of high-performance perovskite-based photodetectors, solar cells, transistors, scintillators, etc.     

Etching characteristics of thin SiON films using a liquefied perfluorocarbon precursor of C6F12O with a low global warming potential

Perfluorocarbon gas is widely used in the semiconductor industry. However, perfluorocarbon has a negative effect on the global environment owing to its high global warming potential (GWP) value. An alternative solution is essential. Therefore, we evaluated the possibility of replacing conventional perfluorocarbon etching gases such as CHF₃ with C₆F₁₂O, which has a low GWP and is in a liquid state at room temperature. In this study, silicon oxynitride (SiON) films were plasma-etched using inductively coupled CF₄ +C₆F₁₂O+O₂ mixed plasmas. Subsequently, the etching characteristics of the film, such as etching rate, etching profile, selectivity over Si, and photoresist, were investigated. A double Langmuir probe was used and optical emission spectroscopy was performed for plasma diagnostics. In addition, a contact angle goniometer and x-ray photoelectron spectroscope were used to confirm the change in the surface properties of the etched SiON film surface. Consequently, the etching characteristics of the C₆F₁₂O mixed plasma exhibited a lower etching rate, higher SiON/Si selectivity, lower plasma damage, and more vertical etched profiles than the conventional CHF₃ mixed plasma. In addition, the C₆F₁₂O gas can be recovered in the liquid state, thereby decreasing global warming. These results confirmed that the C₆F₁₂O precursor can sufficiently replace the conventional etching gas.     

东兴铝业嘉峪关分公司铝灰渣循环利用研究

铝灰渣是铝熔铸过程中产生的废弃物。本文主要介绍了酒钢东兴铝业嘉峪关分公司铝灰渣的产生量、排放、利用情况、化学成分及表面特征,并简要介绍了铝灰渣、铝灰的循环利用途径。     

大宗粉煤灰的综合利用及提质方案

对于大宗粉煤灰原灰进行分选加球磨机粉磨，同时添加合适的激发剂进行提质，可以生产出不同细度和活性的粉煤灰产品，提升粉煤灰在水泥及商品砼中的用量。介绍了某发电公司的粉煤灰处置现状，在此基础上，对商品砼的粉煤灰性能要求进行了大量市场调研，针对性地给出了该公司粉煤灰的提质方案，最后进行了提质粉煤灰的应用市场和产品竞争力分析。     

Electroactive polymers containing 3-arylcarbazolyl units as hole transporting materials for OLEDs

Monomers and their polymers containing 3-arylcarbazolyl electrophores have been synthesized by the multi-step synthetic route. The materials were characterized by thermo-gravimetric analysis, differential scanning calorimetry and electron photoemission technique. The polymers represent materials of high thermal stability having initial thermal degradation temperatures in the range of 331–411 °C. The glass transition temperatures of the amorphous polymeric materials were in the rage of 148–175 °C. The electron photoemission spectra of thin layers of monomers showed ionization potentials in the range of 5.6–5.65 eV. Hole-transporting properties of the polymers were tested in the structures of organic light emitting diodes with Alq₃ as the green emitter. The device containing hole-transporting layers of polyether with 3-naphthylcarbazolyl groups exhibited the best overall performance with a maximum current efficiency of 3.3 cd/A and maximum brightness of about 1000 cd/m².     

甲乙酮装置剩余丁烯的循环利用

对甲乙酮装置剩余丁烯的循环利用进行了研究,采用聚结器脱水-净化的方法,脱除了剩余丁烯中的仲丁醇、仲丁醚、甲乙酮和水分等杂质,使得剩余丁烯得到了循环使用,满足了水合工段的进料要求,同时提高了甲乙酮的产品质量。