洞穴——从微中子研究到地下空间规划

微中子研究需要很大很深的洞穴，以便在没有太多宇宙射线噪音的情况下捕获重要事件。大型的自然洞穴往往出现在喀斯特石灰岩地区，少数大型洞穴也会出现在矿区，而民用洞穴则被广泛用作发电站、火车站、仓库及其他用途。应力控制被认为是在洞穴深挖中消除巨大应力的普遍方法。如果能够在大型洞穴使用应力控制方法，我们就可以建造安全的洞室来进行微中子研究；从另一方面来讲，大而浅的洞穴也能解决城市规划的很多问题。     

Effects of mechanical interactions on the hydrostatic stress in randomly distributed rubber particles in an amorphous polymer matrix

The equivalent inclusion method (EIM) assuming linear elasticity is used to calculate the mechanical interactions between spherical rubber particles in an amorphous matrix, as in a rubber toughened polymer. The influences of the various calculation parameters are examined and it is shown that the method can provide reliable results with regard to the level of hydrostatic stress in the particles. Damage of the material is simulated by replacing the most stressed particles by voids. Numerical simulations for several hundreds of interacting particles give information on the kinetics and spatial organisation of the damage. It appears that, as the volume fraction of particles increases from 10 to 20%, the spatial configuration of the damage evolves from a localised to a diffuse mode. These results are discussed in relation to the efficiency of rubber toughening.     

The 'Conceptual Change In Science' project

Abstract This paper outlines the work of the Conceptual Change in Science project, funded as part of the ESRC InTER programme. The aims of this research project are to clarify and describe the process of change in learners' conceptual understandings of natural phenomena. The domain of reasoning selected for study is that of mechanics. Computer software which may be useful in exploring and developing pupils' reasoning and promoting conceptual change in this domain is being developed and evaluated. The group that is carrying out the research is based at the Universities of Leeds, Glasgow and the Open University.     

Expert system approach for reactor vessel integrity

This paper describes the development strategy of a prototype expert system, called RViES, for the reactor vessel integrity. The main objectives of the system are to assist engineers to perform fatigue and fracture mechanics analyses of reactor vessels quickly and accurately. The system consists of three parts; user interface, knowledge base and inference engine. Various rules recommended in codes and standards are stored in the knowledge base. Several case studies were performed to check the usefulness of the system.     

割缝防砂筛管抗挤强度有限元计算模型

针对割缝防砂筛管周围或缝内部堵塞，造成井眼压力增加，可能会导致筛管被挤毁的问题，采用有限元方法，通过大型有限元程序，建立了其抗挤强度的有限元计算模型。根据弹塑性理论，对割缝防砂筛管进行分析，得出其抗挤强度。结果与国外的实验数据进行对比，数值模拟结果比实验值略大，但两者相差较小，证明了该模型的正确性。为其他尺寸割缝筛管的抗挤强度设计提供了一种数值计算方法。     

Soft and Hard Adhesion

The force needed to pull a cylindrical stud from a soft elastomeric film depends on their elastic and geometric properties. For a rigid stud and a thick elastomeric film, the pull-off stress (σ) depends on the elastic modulus (E) of the film and the radius (a) of the stud as σ ∼ (E/a)^1/2 (soft adhesion). However, when the film is very thin, the pull-off stress is significantly higher than the case with thick films, and its value depends on the elastic modulus and the thickness (h) of the film as σ ∼ (E/h)^1/2 (hard adhesion). Here, we study the pull-off behavior of a soft cylindrical stud, one flat end of which is coated with a high modulus thin baseplate. As the flexural rigidity of this baseplate is varied, we observe the transition between the two types of adhesion. We present a simple physical interpretation of the problem, which could be of value in understanding various biofouling and adhesive situations.     

The effect of annealing on mechanical and tribological properties of diamond-like carbon multilayer films

The diamond-like carbon (DLC) multilayer films have been deposited by plasma CVD deposition onSi wafer substrate. The deposited films have then been post-annealed in vacuum at 250 °C for 2 h. Changes in internal stress, hardness, critical load, friction coefficient and wear have been investigated toassess the influence of annealing on mechanical and tribological properties of DLC multilayer films. At the same time, DLC single layerfilms are also deposited and annealed in the same method for a comparison.The results show that there is 28–33% decrease in internal stress and 10–13% decrease in hardness of theDLC single layer films after the anneal treatment. However, for the DLC multilayer films, there is 41–43% decreasein internal stress and less than 2% decrease in hardness. In addition, the annealed DLC multilayer filmhas the same friction and wear properties as that un-annealed film. This result indicates that the anneal treatment isan effective method for the DLC multilayer films to reduce the internal stress and to increase the critical load.The by-effect of the annealing, decrease of hardness and wear resistance of the multilayer film, can be restrictedby the multilayer structure.     

坯料组成与瓷坯力学性能关系的研究

以长石质瓷为对象，分别研究了坯料的化学矿物组成和颗粒组成的变化与瓷坯抗折强度的关系，利用XRD、SEM等分析手段，探讨了坯料组成及生产工艺制度对瓷坯的岩相组成、显微结构、力学性能的影响。     

ATOMISTIC MOLECULAR DYNAMICS SIMULATIONS OF GAS DIFFUSION AND SOLUBILITY IN RUBBERY AMORPHOUS HYDROCARBON POLYMERS

Diffusion coefficients D of H 2 , He, O 2 , N 2 , and CO 2 in different rubbery amorphous polymeric matrices were estimated by atomistic molecular dynamics simulations at 298 K using the Einstein relationship, and compared with the relevant experimental values, where available. The simulated diffusion coefficients D of all the gases in all polymers considered almost regularly decreased with increasing molecular gas volumes and increasing polymer glass transition temperature. Further, solubility coefficients and heats of solution were obtained for all gases from Grand Canonical Monte Carlo simulations, which were also used to calculate sorption isotherms. In general, there is a good agreement between experimental and simulated values of diffusion and solubility coefficients for all gases considered.