煤层气利用新方案

在介绍煤层气的常规利用方案的基础上，提出了两种利用煤层气的新方案：一是采用变压吸附技术，纯化瓦斯气，将低浓度瓦斯气浓缩为高浓度瓦斯气，加压后成为CNG，用作CNG气源或较远距离城市的天然气气源；二是在第一种方案的基础上，将高浓度瓦斯气全部采用深冷法加以液化，生产LNG，并将LNG运送至更远距离用作LNG加气站、CNG加气站气源。最后还以松藻煤电公司为例，作了新方案的工程预算     

塑料挤出型材车间公用工程设计

鉴于当今人们对塑料门窗需求量的增大，通过对5个塑料挤出型材车间的设计，将其公用工程设计整理成文，总结出塑料挤出型材车间的采暖通风设计，压缩空气系统设计，制冷系统设计的较详尽的方案，以供有关设计技术人员参考。     

鼓风引射式燃气燃烧器的计算

提出鼓风式射式燃气燃烧器的基本计算公式与计算结果，并进行结构尺寸与工况分析，确定各种因素对其的影响程度。     

Experimental densities for compressed R134a

This paper reports densities of compressed R134a (1,1,1,2-tetrafluoroethane) determined by using a contiuously weighed pycnometer at 20 K intervals between 180 and 380 K at pressures from slightly greater than the vapour pressure to 70 MPa. The results are accurate to within ±0.1%. Saturated liquid densities derived by extrapolation from the experimental values agree with other reported values to within ±0.3%.     

3#大布袋收尘器更新改造方案的探讨

通过对3^#大布袋收尘器更新改造方案的对比分析，探讨适合工艺条件的最佳收尘器的选择途径。     

Development of a Magnetic Suspension Densimeter and Measurement of the Density of Toluene

The development of a magnetic suspension densimeter that has been built for measurement of the density of compressed liquid at pressures up to 30 MPa in the temperature range 20 to 150°C is described. The densimeter was first built by the author and his coworkers at NIST. We describe here further improvements made on a second system built at NMIJ based on the same principle. The densimeter uses a small coil suspended from an electronic balance. Within the coil is placed a sample cell in which the pressurized sample and a buoy, which is a permanent magnet, are enclosed. For measurement of density, balance readings are recorded (1) with the buoy at rest and (2) with the buoy in magnetic suspension. The measurement procedure is basically a hydrostatic weighing, which is simpler than those of conventional magnetic densimetry. As an example, measurements of toluene density performed as part of an inter-laboratory comparison are presented. The data agreed with reliable literature values to within a few hundredths of a per cent.     

广钢3#高炉大修工程配套空压站设计

本文阐述了广钢3^#高炉大修工程配套空压站设计方案的选定和实施。     

快速搜寻卫星数字压缩信号

在没有专业仪器，没有明确参照物的条件下，如何快速定位接收天线，搜索到卫星信号，是电视工程技术人员经常遇到的问题，本文就此问题提出了一个新的解决办法，即利用已知卫星的位置来定位其它卫星的位置。     

大泵站超驼峰水位运行压缩空气断流系统的设计方法

阐述了压缩空气断流的原理，提出了压缩空气断流装置的一般构成和设计方法，首次应用气体喷射器作为压缩空气减压增量变换器，不但及时地增加了补气量，防止断流后流道压力的下降，而且大大减小了储气罐容积，使该项技术得以满足工程实际的要求，为同类泵站的技术改造     

压缩式封隔器胶筒变形阶段力学分析

封隔器是常用试采井下工具,胶筒是封隔器中最重要的部件。将压缩式胶筒的变形分为自由变形和约束变形2个阶段,分析了其绝对体积变化规律,得到了使胶筒刚好与井壁接触的轴向力,据此可以确定最小坐封载荷;得到了井壁和中心管对胶筒的约束压力,在此基础上得到了压缩式胶筒的各个应力分量和第四相当应力,据此可以给出坐封力下胶筒的强度,确定合理的坐封力。实例计算解释了现场封隔器胶筒在坐封载荷作用下损坏的原因。