Enhancement of thermal,mechanical, ignition and damping response of magnesium using nano-ceria particles

Magnesium (Mg)-based nanocomposites owing to their low density and biocompatibility are being targeted for transportation and biomedical sectors. In order to support a sustainable environment, the prime aim of this study was to develop non-toxic magnesium-based nanocomposites for a wide spectrum of applications. To support this objective, cerium oxide nanoparticles (0.5?vol%, 1?vol%, and 1.5?vol%) reinforced Mg composites are developed in this study using blend-press-sinter powder metallurgy technique. The microstructural studies exhibited limited amounts of porosity in Mg and Mg-CeO₂ samples (< 1%). Increasing presence of CeO₂ nanoparticles (up to 1.5?vol%) led to a progressive increase in microhardness, dimensional stability, damping capacity and ignition resistance of magnesium. The compressive strengths increased with the increasing addition of the nanoparticles with a significant enhancement in the fracture strain (up to ~48%). Superior energy absorption was observed for all the composite samples prior to compressive fracture. Further, enhancement in thermal, mechanical and damping characteristics of pure Mg is correlated with microstructural changes due to the presence of the CeO₂ nanoparticles.     

Relating catalyst structure and composition to the water–gas shift activity of Cu–Zn-based mixed-oxide catalysts

In order to investigate the effect of cerium oxide on Cu–Zn-based mixed-oxide catalysts four catalyst samples were characterized by means of XRD, in situ XANES and thermogravimetric analysis. The activity of the catalyst samples was tested for the forward water–gas shift reaction. Cerium oxide was found to increase the crystallinity of the ZnO phase indicating a segregation of the Cu and ZnO phases. The TOF of the water–gas shift reaction based on chemisorption data was found to be independent of composition and preparation conditions of the four catalyst samples. In contrast, the catalyst stability depends on composition and preparation conditions. Cerium oxide impregnated before calcination of the hydrotalcite-based Cu–Zn precursors leads to a more stable water–gas shift catalyst.     

Effects of surfactant/silica and silica/cerium ratios on the characteristics of mesoporous Ce-MCM-41

Using the surfactant CTMABr (cetyltrimethyl ammonium bromide) and cerium(IV) sulfate, mesoporous Ce-MCM-41 molecular sieves were produced under a hydrothermal condition with various surfactant/silica (surfactant/Si) and silica/cerium (Si/Ce) ratios. Changes to the structural traits caused by changing the molar ratios of both surfactant/Si and Si/Ce were investigated. XRD (X-ray diffraction), FT-IR (fourier transform infrared spectroscopy), and SEM (scanning electro microscopy) were used for the characterization of prepared mesoporous samples. Among the tested molar ratios, surfactant/Si ratio of 0.5 and 0.2 showed highest values of d_1 0 0 and intensity, respectively, for the Si-MCM-41. XRD analysis also identified a quintessential hexagonal structure of Ce-MCM-41 for the Si/Ce molar ratio higher than 40 (maintaining the surfactant/Si ratio at 0.2). When cerium content was increased to have the Si/Ce molar ratio of 20, the hexagonal structure of Ce-MCM-41 was collapsed due to the structural stress of substituted cerium. FT-IR results confirmed calcination of Ce-MCM-41 and the incorporation of Ce⁴⁺ ions of cerium sulfate into the silica surface with proper removal of the surfactant. Rod-like shape with rounded edges of the prepared Ce-MCM-41 samples was identified by SEM. These results suggest surfactant/Si ratio of 0.2 and Si/Ce ratio of 40 for the production of Ce-MCM-41 with the highest level of crystallinity.     

Surface Chemistry and Catalysis of Rare Earth Oxides I．A Study of the Reactivity of Surface Hydroxyls on CeO_2 and Pr_6O_（11） by FT－IR Spectroscopy

ＳｕｒｆａｃｅＣｈｅｍｉｓｔｒｙａｎｄＣａｔａｌｙｓｉｓｏｆＲａｒｅＥａｒｔｈＯｘｉｄｅｓＩ．Ａ　ＳｔｕｄｙｏｆｔｈｅＲｅａｃｔｉｖｉｔｙｏｆＳｕｒｆａｃｅＨｙｄｒｏｘｙｌｓｏｎＣｅＯ_２ａｎｄＰｒ_６Ｏ_（１１）ｂｙＦＴ－ＩＲＳｐｅｃｔｒｏｓｃｏｐｙ...     

Studies on the corrosion behavior of cerium-implanted zircaloy-4 with GAXRD

In order to study the influence of cerium ion implantation on the aqueous corrosion behavior of zircaloy-4, specimens were implanted by cerium ions with a fluence range from 1×10¹⁶ to 1×10¹⁷ ions/cm² at maximum 150°C, using MEVVA source at an extracted voltage of 40 kV. The valence and elements penetration distribution of the surface layer were analyzed by X-ray photoelectron spectroscopy (XPS) and auger electron spectroscopy (AES) respectively. Glancing angle X-ray diffraction (GAXRD) was employed to examine the phase transformation due to the cerium ion implantation in the oxide films. Three-sweep potentiodynamic polarization measurement was employed to value the aqueous corrosion resistance of zircaloy-4 in a 1 N H₂SO₄ solution. It was found that a significant improvement in the aqueous corrosion behavior of zircaloy-4 implanted with cerium ions compared with that of the as-received zircaloy-4. The improvement effect will declined with raising the implantation fluence. The bigger is the fluence, the less is the improvement. Finally, the mechanism of the corrosion behavior of the cerium-implanted zircaloy-4 is discussed.     

CeO2 和MgO助烧剂对矾土基莫来石合成料烧结的影响

以高铝矾土碎矿(w(Al2O3)为75%~84%)和煤矸石(w(Al2O3)约45%)为原料,按矾土基莫来石合成料的设计成分要求(w(Al2O3)为68%~72%)进行配比,于1500~1700℃分别保温3h煅烧合成了矾土基莫来石,并分别研究了助烧剂CeO2和MgO单独加入,CeO2 MgO复合加入,复合加入时CeO2与MgO的比例以及复合加入量对矾土基莫来石合成料烧结性能的影响。结果表明:加入CeO2 MgO复合助烧剂比单独加入CeO2或MgO的促烧结效果要好,当CeO2 MgO外加量为0.75%,CeO2与MgO质量比为1/1时,可使试样的烧结温度降至1600℃(不加助烧剂的为1700℃),得到显气孔率0.9%,体积密度为2.84g·cm-3,荷重软化开始温度为1570℃的合成莫来石;显微结构分析表明,此合成料荷重软化温度较高的原因是发育良好的柱状莫来石构成了交错连锁的网络结构,同时TiO2大部分固溶在莫来石晶体中。     

Effect of HCl pre-treatment on corrosion resistance of cerium-based conversion coatings on magnesium and magnesium alloys

The corrosion protection afforded by a cerium conversion coating, formed by immersion in a solution containing rare earth salt and hydrogen peroxide, on pure magnesium and two magnesium alloys, AZ91 and AM50, has been studied. The effect of HCl pre-treatments on the morphology and on the corrosion resistance of the cerium conversion layer was investigated. A thicker and more homogeneous distribution of the conversion coating was obtained when the sample surface was pre-treated with acid. Higher amounts of cerium on the surface of the pre-treated samples were detected. The cerium conversion coating increased the corrosion resistance of the alloys because it ennobled the corrosion potential and decreased both the anodic and cathodic current. The acid pre-treatment further increased the corrosion resistance of the coated alloys. After five days of immersion in chloride environment the untreated samples showed localized corrosion while the chemical conversion coated samples appeared unaffected.     

Catalytic feasibility of Ce-doped LaCoO3 systems for chlorobenzene oxidation: An analysis of synthesis method

A family of Ce-doped LaCoO₃ perovskites are presented as possible catalysts for Cl–VOCs elimination. These materials with different contents of Ce were obtained through the citrate and the reactive grinding methods. The insertion of Ce in the original perovskite structure favours the presence of Co²⁺/Co³⁺ and Ce³⁺/Ce⁴⁺ redox pairs and a higher content of oxygen vacancies that enhances the catalytic performance in chlorobenzene combustion based on differential kinetics studies. The family obtained by the grinding method presents a performance as high as that synthesized by citrate method. Thus, the reactive grinding is a feasible green chemistry alternative to obtain a catalyst with the same performance as that obtained from traditional methods. Finally, the stability of samples was evaluated under total combustion reaction conditions showing an excellent activity during 45 h time on stream.     

X-ray photoelectron spectroscopic study of the oxidation and reduction of a cerium(III) oxide/cerium foil substrate

X-ray photoelectron spectroscopy has been used to examine the nature of the oxide overlayers on a passivated cerium metal foil as a function of a variety of oxidation and reduction treatments. Oxidation of a clean uncontaminated cerium(III) oxide surface is facile at room temperature and produces non-stoichiometric ceria (CeO_2–x) at oxygen doses as low as 10 L. At higher doses the overlayer thickens, and after a dose of 160 L the layer depth exceeds the Ce 3d photoelectron attenuation distance of about 20 Å. High pressure treatment of the foil in oxygen (0.5 bar at RT and 473 K) produces CeO₂ in a high degree of crystallographic order such that O 1s photoelectron intensities are increased above that expected from a randomly oriented powder. An attempt to reduce the CeO₂ layer formed by controlled oxidation with CO (633 K, 14 h, 0.6 bar) results in the formation of a carbonated surface layer. Results following attempts to reoxidise this layer are discussed.