中厚板轧制边部不均匀变形机理的探讨

通过分析宽中厚板轧制过程中的边部不均匀变形，探讨了其影响因素及大宽度板“切边纵裂”的产生原因，提出了解决问题的具体办法。     

单轴传动滚切式双边剪薄钢板剪后“错牙”及“飞边”的原因分析与对策

针对单轴传动滚切式双边剪生产过程中出现的薄钢板经双边剪剪后出现“错牙”及“飞边”的问题,从多个方面入手对薄钢板出现“错牙”及“飞边”的原因进行了分析对比,提出了相应的解决方案,对今后滚切式双边剪的设计、制造及安装调试有借鉴和参考价值。     

酒钢中板厂技术改造

酒钢中板厂的改造实现了中板工序产能达到年产150万吨左右，增加粗轧机等设备，将现有单机架生产线改为双机架生产线，精整线改为双线，附带提升整个生产线的技术经济指标。改造工程在尽可能地不影响或少影响生产的条件下进行，同时解决原生产线存在的一些缺陷和瓶颈问题。     

济钢中厚板厂的技术改造与发展

结合济钢中厚板厂二期和三期工程、开发管线钢项目和大板坯连铸高效改造及炉外精炼改造，介绍了该厂的技术改造项目，对今后的发展进行了阐述．     

Natural convection from narrow horizontal plates at moderate Rayleigh numbers

The present work deals with the natural convection flow and heat transfer from a horizontal plate cooled from above. Experiments are carried out for rectangular plates having aspect ratios between φ=0.036 and 0.43 and Rayleigh numbers in the range 290?Ra_w?3.3×10⁵. These values of Ra_w and φ have been selected below those commonly considered in previous research in view of a future application to the design of printed circuit boards. The plates are made of two different metals, copper and steel. The choice of a metal is relevant to the present problem because the plates are heated by means of an electric current. Important variations of the surface temperature are observed along the transverse direction for the steel plates. The surface of the copper plates is almost isothermal because of the high thermal conductivity of the metal.Calculations for a semi-infinite plate are carried out to predict the transverse profiles of the surface temperature and heat flux and to visualize the structure of the flow. Three-dimensional calculations are also used at a qualitative level to observe the changes in the flow structure due to the finite length of the plate. Present results are compared with both previous experimental work and analyses that are based on boundary layer theory. It is shown that analyses for an infinite boundary layer are not completely applicable to the present problem because of its different physics. The most relevant feature of the natural convection flow, which is not predicted by boundary layer analyses, is a thermal plume rising near the center of the plate.Present heat transfer results differ from previous experimental work because of the lower Rayleigh numbers and aspect ratios investigated here. The Nusselt number is found to depend on Ra_wⁿ, with the exponent n=0.17 being lower than most of the values reported in the literature. This comparatively low value is related to the transverse conduction of heat through the air, which becomes increasingly significant as Ra_w approaches zero. It is shown that such a low-Ra_w effect can be accounted for in a physically consistent manner by adding a constant term to the heat transfer correlation. On the other hand, it is found that the Nusselt number does not significantly depend on the aspect ratio in the range of φ investigated contrary to what has been previously reported for wider plates.     

南钢中板厂电气设备可靠性保障方法

本文介绍了南钢中板厂将系统工程最优化技术中的随机服务系统理论和可靠性设计方法引入到电气设备的维护和管理工作中，并结合现场实际情况摸索出一套电气设备可靠性保障方法。     

主动约束层阻尼板结构动力学建模研究

将有限元法和GHM法相结合，给出了建立主动约束层阻尼（ACLD）板结构动力学模型的新方法。建模时，考虑到粘弹材料（VEM）的纵向位移影响，采用GHM方法描述VEM的本构关系，解决了VEM的力学特性随温度和频率变化的难点，避免因VEM的复杂本构关系而产生的微分积分方程。算例表明本文给出的建模方法是准确的，ACLD结构能够有效控制结构振动。     

板式换热器热端跑冷问题的分析及处理

１００００ｍ３／ｈ制氧机板式换热器损坏修复后，热端跑冷严重，氧气取出量不足，制氧机工况恶化，通过分析找出了原因是因某单元氧通道堵塞，并采取了处理措施。     

Effect of plate aspect ratio on the recovery of deuterium from water-isotope mixture in flat-plate thermal diffusion columns with transverse sampling streams

The optimal plate aspect ratios for the best recovery of deuterium from water-isotope mixture in flat-plate thermal diffusion columns with transverse sampling streams have been determined. The maximum recovery and maximum production rate are achieved without changing the total expenditure, while the design with minimum plate surface area results in minimizing the total expense.     

Cu—Cr合金电极触头板铸件的熔制

含０．４％～１．０％Ｃｒ的Ｃｕ－Ｃｒ合金具有优良的导电、导热性能，铸件经热处理强化后可获得较高的综合力学性能。近年来该合金作为一种新材料被广泛地用于制作电子工业、电器设备上的电极触头板、接触环、夹持体等零件。Ｃｕ－Ｃｒ合金存在易氧化吸气、凝固范围窄、收缩较大、易形成集中缩孔等缺陷，这些铸造特性给生产优良的Ｃｕ－Ｃｒ合金铸件带来一定的困难。以采用常规的熔炼设备和造型材料熔铸出Ｃｕ－Ｃｒ合金铸件——高压大电流电极触头板为例讨论这一熔铸的工艺方法。