Evaluation of hydrodynamic behavior of the perforated gas distributor of industrial gas phase polymerization reactor using CFD-PBM coupled model

A 2D computational fluid dynamics (Eulerian–Eulerian) multiphase flow model coupled with a population balance model (CFD-PBM) was implemented to investigate the fluidization structure in terms of entrance region in an industrial-scale gas phase fluidized bed reactor. The simulation results were compared with the industrial data, and good agreement was observed. Two cases including perforated distributor and complete sparger were applied to examine the flow structure through the bed. The parametric sensitivity analysis of time step, number of node, drag coefficient, and specularity coefficient was carried out. It was found that the results were more sensitive to the drag model. The results showed that the entrance configuration has significant effect on the flow structure. While the dead zones are created in both corners of the distributors, the perforated distributor generates more startup bubbles, heterogeneous flow field, and better gas–solid interaction above the entrance region due to jet formation.     

Upscaled DEM-CFD model for vibrated fluidized bed based on particle-scale similarities

Simulation based on discrete element method (DEM) coupled with computational fluid dynamics (CFD), coupled DEM-CFD, is a powerful tool for investigating the details of dense particle–fluid interaction problems such as in fluidized beds and pneumatic conveyers. The addition of a mechanical vibration to a system can drastically alter the particle and fluid flows; however, their detailed mechanisms are not well understood. In this study, a DEM-CFD model based on a non-inertial frame of reference is developed to achieve a better understanding of the influence of vibration in a vibrated fluidized bed. Because the high computational cost of DEM-CFD calculations is still a major problem, an upscaled coarse-graining model is also employed. To realize similar behaviors with enlarged model particles, non-dimensional parameters at the particle scale were deduced from the governing equations. The suitability and limitations of the proposed model were examined for a density segregation problem of a binary system. To reduce the computational costs, we show that the ratio between the bed width and model particle size can be reduced to a minimum value of 100; to obtain similar segregation behaviors, the ratio between the bed height and model particle size is considered unchanged.     

油页岩矿物质催化半焦燃烧特性及机理

利用微型流化床反应分析仪（MFBRA）研究了油页岩矿物质催化半焦燃烧特性，重点考察了半焦内部矿物质和外部页岩灰床料对半焦燃烧的催化作用，揭示了流化床反应器中半焦燃烧过程和机理。结果表明：内部矿物质和外部床料对半焦燃烧均具有明显催化作用，而两者共同催化效果最为显著。矿物质中CaO和Fe₂O₃对半焦燃烧具有催化活性，CaO催化作用强于Fe₂O₃。油页岩半焦燃烧反应活化能在60.41~78.97 kJ/mol之间，矿物质的催化作用会明显降低反应活化能。流化床反应器中，矿物质对半焦燃烧的催化作用主要表现在四个反应，即：挥发分裂解和燃烧、半焦表面炭燃烧、半焦内部炭燃烧以及一氧化碳燃烧。     

催化裂化汽油光化学氧化脱硫

以水为萃取剂、空气中的O2为氧化剂、500W高压汞灯为紫外光光源,研究了催化裂化(FCC)汽油光化学氧化反应的机理和氧化产物,考察了反应条件对FCC汽油脱硫率的影响。实验结果表明,FCC汽油中的极性含硫化合物首先部分溶于水相中,然后在水相中被氧化。在空气通入量为150mL/min、水与FCC汽油的体积比为1.0的条件下,反应5h后FCC汽油脱硫率达40.6%,加入0.45g4A分子筛作为O2的吸附剂后FCC汽油脱硫率提高到70.2%。FCC汽油的光化学氧化反应为一级动力学反应,加入4A分子筛时的反应速率常数为0.217 4h-1,半衰期为3.18h。FCC汽油光化学氧化反应的主要产物为亚砜和砜,并进一步生成CO2、草酸、SO24-等。     

内循环好氧三相流化床处理造纸中段废水

本实验采用内循环好氧三相流化床处造纸中段废水，经过一段时间的驯化，获得了稳定的出水。CDO去除经保持在65％以上，系统对进水污染负荷的变化具有较大的承受能力。出水Cl^-的浓度有所增加，说明驯化后的微生物可能对有抽氯化物具有一定的降解作用。水气比在1／120至1／140之间可获得最好的COD去除效果。后进行絮凝处理后，出水COD降为60－80mg/L,BODo 50-60/L，色度为100－150CU，挥发性酚的质量浓度小于0．0265mg／L。     

Fluctuations and waves in fluidized bed systems: The influence of the air-supply system

A general model of the response of a fluidized bed to disturbances is formulated, and the information provided by the model with respect to the dynamics of the bed, the bed plus the air-plenum and the bed plus the entire air-supply system, is investigated. Expressions given in literature on the fundamental frequency of the bed-plenum system are analyzed, and it is shown that they are a special case of the general model. In order to simulate various types of interaction between the bed and the rest of the system, experiments were performed in a cold fluidized bed unit operated under both non-circulating and circulating conditions. At low velocity, three regimes were identified: the multiple bubble regime with almost no interaction between bed and air-plenum, the single bubble regime with the interaction between bed and air-plenum only, and a regime with numerous irregular bubbles, where the bed interacted with the entire air-supply system. At high fluidization velocity, the exploding bubble regime was identified, with the same dominant frequency as that of the single bubble regime (the interaction with the air-supply system remains at that frequency). The models investigated correctly reproduce the dynamics when the bed is independent of the other parts of the system, or when the bed interacts only with the air-plenum. However, the models are only partially applicable when the bed interacts with the entire air-supply system. The reasons for this are investigated. In the case of system interaction, pressure waves, generated in the bed, interact with pressure pulsations from the air-supply system. This results in a coupled system, which is not covered by the models. Pressure waves resulting from events in the bed, are recognized as the coherent part of the cross power spectra of pressure fluctuations measured in the bed and the air-plenum.     

Exit effect on hydrodynamics of the internal circulating fluidized bed riser

This is the first time an extensive investigation has been carried out regarding the effects of riser exit geometry on pressure drop and solid behaviour inside the Internal Circulating Fluidized Bed (ICFB) riser, using different riser exit geometries at several operating conditions.The Radioactive Particle-Tracking (RPT) technique was used for solid concentration measurements and solid residence time distribution at the exit zone. Experiments were conducted using Geldart B particles, in the gas superficial velocity range of 4 to 10 m/s. Axial solid hold-up, solid residence time distribution in the exit zone, and the reflux ratio factor k_m, (defined earlier by [E.H. Van der Meer, R.B. Thorpe, J.F. Davidson, Flow patterns in the square cross-section riser of a circulating fluidized bed and the effect of riser exit design, Chem. Eng. Sc. 55 (19) (2000) 4079-4099]), were the main criteria used to investigate the impact of gas-solid separator devices implemented at the ICFB riser exit.Solid residence time distribution results and axial solid hold-up profiles provided clear evidence that the separator device at the riser exit strongly influences the hydrodynamic structure of the ICFB riser. The V-shaped riser exit geometry was found to be the optimum of all the configurations studied.     

Simultaneous sulfide and acetate oxidation under denitrifying conditions using an inverse fluidized bed reactor

BACKGROUND: Simultaneous removal of sulfur, nitrogen and carbon compounds from wastewaters is a commercially important biological process. The objective was to evaluate the influence of the CH₃COO^?/NO₃^? molar ratio on the sulfide oxidation process using an inverse fluidized bed reactor (IFBR). RESULTS: Three molar ratios of CH₃COO^?/NO₃^? (0.85, 0.72 and 0.62) with a constant S^2?/NO₃^? molar ratio of 0.13 were evaluated. At a CH₃COO^?/NO₃^? molar ratio of 0.85, the nitrate, acetate and sulfide removal efficiencies were approximately 100%. The N₂ yield (g N₂ g^?1 NO₃^?‐N consumed) was 0.81. Acetate was mineralized, resulting in a yield of 0.65 g inorganic‐C g^?1 CH₃COO^?‐C consumed. Sulfide was partially oxidized to S⁰, and 71% of the S^2? consumed was recovered as elemental sulfur by a settler installed in the IFBR. At a CH₃COO^?/NO₃^? molar ratio of 0.72, the efficiencies of nitrate, acetate and sulfide consumption were of 100%, with N₂ and inorganic‐C yields of 0.84 and 0.69, respectively. The sulfide was recovered as sulfate instead of S⁰, with a yield of 0.92 g SO₄^2?‐S g^?1 S^2? consumed. CONCLUSIONS: The CH₃COO^?/NO₃^? molar ratio was shown to be an important parameter that can be used to control the fate of sulfide oxidation to either S⁰ or sulfate. In this study, the potential of denitrification for the simultaneous removal of organic matter, sulfide and nitrate from wastewaters was demonstrated, obtaining CO₂, S⁰ and N₂ as the major end products. Copyright © 2008 Society of Chemical Industry     

2,4,6‐Trichlorophenol and phenol removal in methanogenic and partially‐aerated methanogenic conditions in a fluidized bed bioreactor

A fluidized bed bioreactor (FBBR) was operated for more than 575 days to remove 2,4,6‐trichlorophenol (TCP) and phenol (Phe) from a synthetic toxic wastewater containing 80 mg L^?1 of TCP and 20 mg L^?1 of Phe under two regimes: Methanogenic (M) and Partially‐Aerated Methanogenic (PAM). The mesophilic, laboratory‐scale FBBR consisted of a glass column (3 L capacity) loaded with 1 L of 1 mm diameter granular activated carbon colonized by an anaerobic consortium. Sucrose (1 g COD L^?1) was used as co‐substrate in the two conditions. The hydraulic residence time was kept constant at 1 day. Both conditions showed similar TCP and Phe removal (99.9 + %); nevertheless, in the Methanogenic regime, the accumulation of 4‐chlorophenol (4CP) up to 16 mg L^?1 and phenol up to 4 mg L^?1 was observed, whereas in PAM conditions 4CP and other intermediates were not detected. The specific methanogenic activity of biomass decreased from 1.01 ± 0.14 in M conditions to 0.19 ± 0.06 mmolCH₄ h^?1 gTKN^?1 in PAM conditions whereas the specific oxygen uptake rate increased from 0.039 ± 0.008 in M conditions to 0.054 ± 0.012 mmolO₂ h^?1 gTKN^?1, which suggested the co‐existence of both methanogenic archaea and aerobic bacteria in the undefined consortium. The advantage of the PAM condition over the M regime is that it provides for the thorough removal of less‐substituted chlorophenols produced by the reductive dehalogenation of TCP rather than the removal of the parent compound itself. Copyright © 2005 Society of Chemical Industry