The method of testing of XLPE cable insulation resistance to partial discharges and electrical treeing

The paper gives a method of model XLPE medium voltage cable insulation testing for partial discharges and electrical treeing with a point to plane test geometry. Based on this method, a comparative estimate of insulation resistance to treeing and partial discharges have been made. XLPE crosslinked by different methods (steam medium and hot nitrogen medium) and with varying contents of inorganic filler kaolin were tested. The characteristics of partial discharges were measured by means of a pulse height analyser characterized with a microscope. The data have been analysed statistically.     

生态水力学法在河段最小生态需水量计算中的应用

以雅砻江锦屏二级水电站建成后造成坝后119 km的减水河段为例,用生态水力学法计算了减水河道最小生态流量,得出为满足减水河段鱼类的生存及繁衍,枯水季节猫猫滩闸址处必须保证下泄45 m3/s流量,在该流量下,锦屏二级水电站减水河段中95%左右河段水深、流速、水面宽、湿周率、过水断面面积、水面面积等水力因子可满足河道内鱼类的生存繁衍;水温的变化不会影响河道内鱼类的产卵;鱼类适应的缓流、急流、浅滩、深潭等水力形态的位置发生变化,数量保持不变。总的来说,水生生物的生物量将随着河道流量的减小而减少,但种群数量将保持不变。该实例为生态水力学法计算河道最小生态需水量做了一些探索性的研究工作。     

放电声发射波检测中数据预处理的小波分析实现

研究了放电声发射波检测中用小波变换进行数据预处理的实现问题。内容包括小波分析预处理的步骤 ,选择小波 ,选择小波分解层数 ,提取有用频段的小波系数 ,小波消噪过程 ,小波消噪中的阈值选取 ,对提取的小波系数进行小波消噪等。两组实测信号的小波分析数据预处理结果证明了数据预处理的有效性     

Atmospheric-pressure dielectric barrier discharge generation by a full-bridge flying capacitor multilevel inverter

A new configuration of a resonant full-bridge flying capacitor multicell inverter has been designed and constructed with the aim of achieving an extended output voltage frequency range with low harmonic distortion and reduced semiconductor commutation losses. This configuration was tested as a power supply for two different coaxial dielectric barrier discharge reactors, one of them employed for electric characterization and the other one for inorganic compound elimination in an aqueous solution. Two different gas mixtures, 90% Ar–10% O_2 and80% Ar–20% O_2, were individually supplied during the experiments; the results showed a highefficiency removal of meta-cresol(m-cresol) to the order of 98%, which was obtained by adding more oxygen to the plasma gas mixture.     

Lightning Observation in 3D Using a Multiple LF Sensor Network and Comparison with Radar Reflectivity

A three‐dimensional (3D) lightning mapper consisting of multiple low‐frequency (LF) sensors has been developed to monitor thunderstorms and to estimate their charge structure. We have been conducting an observation campaign using the 3D lightning mapper in Kansai, Japan, since October 2012. In this study, we determine 3D source locations of intracloud and cloud‐to‐ground flashes and compare them with the radar reflectivity estimated by phased‐array radar (PAR) with high temporal and spatial resolution. Most LF sources are located in high radar reflectivity regions, confirming that the 3D LF lightning mapper monitors thunderstorms. A lightning flash with heavy branches is clearly imaged. Based on the bidirectional leader theory that negative and positive ends of a lightning leader develop simultaneously, we estimate the positive and negative charge regions in a thundercloud from the LF source locations. The radar reflectivity estimated by PAR supports the charge structure estimated by LF source locations.     

Functionalization of Polymer Surfaces Using Excimer VUV Systems and Silent Discharges. Application to Electroless Metallization

New approaches for electroless plating of nonconductive polymers or polymer-based materials are described. In this work, polyimide substrates were surface-functionalized (i) in nitrogenated (ammonia at reduced pressure) and oxygenated (air at atmospheric pressure) atmospheres under assistance of vacuum-ultraviolet (VUV) irradiation (use of a xenon silent discharge excimer source) or (ii) directly in air at atmospheric pressure using a dielectric-barrier discharge (DBD) device. After functionalization, the substrates were “activated” by dipping in a dilute acidic PdCl₂ solution or by spin-coating of a thin metal-organic film (from a solution of palladium acetate (PdAc) in chloroform). The catalytic activity of the so-deposited palladium species toward the electroless deposition of nickel was studied before and after a VUV post-irradiation (in air at atmospheric or reduced pressure) with a view to understanding better the role of the reducer (sodium hypophosphite) within the electroless bath.

This work confirms the specific interest of grafting nitrogenated functionalities onto polymer surfaces for attaching covalently the palladium-based catalyst (in particular in the case of the PdCl₂ route), forming thus strong Pd - N - C bonds at the metal/polymer interface. This results from the strong chemical affinity of palladium toward nitrogen. On the other hand, when oxygenated functionalities are surface-grafted, the conventional two-step procedure using SnCl₂ and PdCl₂ solutions can be proposed due to the strong chemical affinity of tin toward oxygen. The Ni deposits obtained under these different conditions pass the standard Scotch^®-tape test and, therefore, exhibit a good practical adhesion. For this same purpose, it is interesting to note that the DBD treatment operating in air at atmospheric pressure causes an increase of the surface roughness and, therefore, an improvement in adhesion of metallic films when their initiation is catalyzed through the PdAc route. In addition, this work demonstrates that extensive research still has to be performed to understand and improve the Ni/polymer adhesion when the PdAc route associated with a VUV irradiation is considered.     

Probabilistic environmental risk assessment of urban wet-weather discharges: an approach developed for Switzerland

Technical solutions aimed at limiting the impacts of urban wet-weather discharges are historically based on an end-of-pipe approach. The characteristics of wet-weather discharges, e.g. intermittent pollution loads, high variations in pollutant concentrations, effects in the receiving waters, etc., are generally not considered. This study presents a new probabilistic approach that links the characteristics of wet-weather discharges to their potential impacts in receiving waters. This new approach involves coupling a model for predicting fluctuating concentrations in rivers along with sediment changes to water quality criteria. The new approach produces a risk profile for receiving waters and includes assessment of uncertainty in input data as well as the uncertainty inherent in local receiving system processes. This new approach is expected to offer a better management of wet-weather discharges, resulting in lower environmental impacts.     

Single-end Partial Discharge Location in Power Cables Based on Phase Difference Method

This paper describes the application of phase difference method for locating partial discharge （PD） in power cables from single-end measurement. The phase difference between the direct and reflected wa...     

Building micro and nanosystems with electrochemical discharges

Since the discovery of the electrochemical discharge phenomenon by Fizeau and Foucault, several contributions have expanded the wide range of applications associated with this high current density electrochemical process. The complexity of the phenomenon, from the macroscopic to the microscopic scales, led since then to experimental and theoretical studies from different research fields. This contribution reviews the chemical and electrochemical perspectives where a mechanistic model based on results from radiation chemistry of aqueous solutions is proposed. In addition applications to micro-machining and fabrication of nanoparticles are discussed.     

Kinetic model of solute aqueous extraction from Fennel (Foeniculum vulgare) treated by pulsed electric field, electrical discharges and ultrasonic irradiations

This work investigates the aqueous extraction from Fennel (Foeniculum vulgare) assisted by pulsed electric field (PEF), electrical discharges (ED) and ultrasound irradiations (UI). It aims the improvement of the solutes yield and the extraction kinetics at room temperature.Fennel gratings of size (1.5 × 0.75 × 30-50 mm³; width × height × length), were treated by PEF (intensity: 50-1200 V/cm and number of pulses: 50-1000), ED (voltage: 40 kV and number of discharges: 10-60) and ultrasound (intensity: 400 W/cm² and treatment duration: 10-350 min). The liquid-to-solid (weight/weight) ratio equal to 2. All tests were carried out at room temperature (20 °C), under stirring at 250 rpm. The extraction kinetics was modelled using a simplified two-exponential kinetic model, which corresponds to mass transfer in two stages (rapid washing and slow diffusion).The optimal parameters of PEF, ED and UI, giving the maximal juice yield, were determined and the effect of these three treatments on the mass transfer rate was studied.