Experimental study and model predictions on helium release in an enclosure with single or multiple vents

This paper presents experiments performed at Canadian Nuclear Laboratories (CNL) to examine the dispersion behaviour of helium in a polycarbonate enclosure that was representative of a residential parking garage. The purpose was to gain a better understanding of the effect of buoyancy- or wind-driven natural ventilation on hydrogen dispersion behaviour. Although hydrogen dispersion studies have been reported extensively in the literature, gaps still exist in predictive methods for hazard analysis. Helium, a simulant for hydrogen, was injected near the centre of the floor with a flow rate ranging from 5 to 75 standard litres per minute through an upward-facing nozzle, resulting in an injection Richardson number ranging between 10^?1 and 10². The location of the nozzle varied from the bottom of the enclosure to near the ceiling to examine the impact of the nozzle elevation on the development of a stratified layer in the upper region of the enclosure. When the injection nozzle was placed at a sufficiently low elevation, the vertical helium profile always consisted of a homogenous layer at the top overlaying a stratified layer at the bottom. To simulate outdoor environmental conditions, a fan was placed in front of each vent to examine the effect of opposing or assisting wind on the dispersion. The helium transients in the uniform layer predicted with analytical models were in good agreement with the measured transients for most tests. Model improvements are required for adequately predicting transients with primarily stratified profiles or strong opposing wind.     

Experimental investigation on the invert stability of operating railway tunnels with different drainage systems using 3D printing technology

In recent years, the invert anomalies of operating railway tunnels in water-rich areas occur frequently, which greatly affect the transportation capacity of the railway lines. Tunnel drainage system is a crucial factor to ensure the invert stability by regulating the external water pressure (EWP). By means of a three-dimensional (3D) printing model, this paper experimentally investigates the deformation behavior of the invert for the tunnels with the traditional drainage system (TDS) widely used in China and its optimized drainage system (ODS) with bottom drainage function. Six test groups with a total of 110 test conditions were designed to consider the design factors and environmental factors in engineering practice, including layout of the drainage system, blockage of the drainage system and groundwater level fluctuation. It was found that there are significant differences in the water discharge, EWP and invert stability for the tunnels with the two drainage systems. Even with a dense arrangement of the external blind tubes, TDS was still difficult to eliminate the excessive EWP below the invert, which is the main cause for the invert instability. Blockage of drainage system further increased the invert uplift and aggravated the track irregularity, especially when the blockage degree is more than 50%. However, ODS can prevent these invert anomalies by reasonably controlling the EWP at tunnel bottom. Even when the groundwater level reached 60 m and the blind tubes were fully blocked, the invert stability can still be maintained and the railway track experienced a settlement of only 1.8 mm. Meanwhile, the on-site monitoring under several rainstorms further showed that the average EWP of the invert was controlled within 84 kPa, while the maximum settlement of the track slab was only 0.92 mm, which also was in good agreement with the results of model test.     

基于TRNSYS的茯砖茶生产工艺能源系统节能环保特性研究

茯砖茶发酵、干燥过程中，烘房内温湿度稳定性和能源系统低能耗是保证茯砖茶品质与成本的重要因素。本文采用TRNSYS仿真与实验研究相结合的方法，对咸阳某茯砖茶厂实际使用的空气源热泵系统进行建模，通过研究各季节典型代表月烘房温湿度的波动情况，确定该空气源热泵系统在全年的运行状态是否满足工艺要求，在此基础上，对比了该系统在全年可运行季节代表月与该生产厂房早期使用的燃气锅炉系统的能耗仿真结果，对空气源热泵系统的节能与环保特性进行研究。结果表明：由于夏季送风质量流量过大且室外空气含湿量较高，7月烘房温湿度不满足工艺要求。热泵系统在1、4、10月的总标煤消耗量的平均值是锅炉系统的44.42%，平均CO2、SO2、NOx排放量分别为锅炉系统的34.13%、44.1%、40.60%。在茯砖茶发酵、干燥的过程中，相比于燃气锅炉系统，空气源热泵系统具有更好的节能与环保特性。     

A model- and simulation-based approach for tolerancing and verifying the functional capability of micro/nano-structured workpieces

The evaluation of functional features of manufactured workpieces is based on GO- and NO-GO-test results, which are obtained by comparing measured geometric characteristics with nominal dimensions and tolerances specified by the designer. These geometrical specifications are based on a tolerancing system, which was originally defined for the function mating capability. Against the background of upcoming lots of other new functions (like reduction of flow resistance, light absorption, reduction of friction, diffraction of light, self-cleaning or mass transmission) are to be realized with our products – particularly by micro- and nano scaled features. If the verification process will deliver the prediction of the achievable degree of functionality, the usability of a part can be assessed more accurately and in consequence quality and economics can be improved. So, a new principle for tolerancing and verifying turns out to be necessary. In this paper the fundamental deficit of the actual tolerancing and specification systems GPS and ASME Y14.5 is derived and the path for enlarging the system by preposing a functional model is shown. To verify the functional capability of the workpieces an approach based on simulations done with the parameterized mathematical–physical model of the function is suggested. Advantages of this approach will be discussed and demonstrated by examples with microstructured inking rolls, crankshafts and injection valves.     

论携号转网行为的私法规制

以电信用户入网协议为切入点,电信用户的携号转网行为应受到《合同法》《消费者权益保护法》等私法规范的保护与限制。该行为引起的格式条款解释、合同终止、违约责任、损失赔偿等问题,不能仅靠《电信条例》等公法规范来调整。应当积极引导广大消费者用户以私法领域相关规定为依据,转变争议解决思维,拓宽纠纷处理途径,合理选择维权手段,以保护自身合法民事权益,与行业监管部门共同推动电信行业有序发展。     

柠檬酸铋合成新工艺研究

针对现有柠檬酸铋制备工艺合成时间长、能耗高、产品纯度不高等不足,介绍了一种常温下制备柠檬酸铋的新工艺。新工艺制备时间短,制备的柠檬酸铋产品质量好,合成过程产生的废水可循环利用,废气经碱液循环吸收可生产硝酸钠副产品。