基于西门子楼宇自控系统的中央空调计费系统

介绍了基于西门子楼宇自控系统的空调计费系统的软硬件设计和具体实现.该系统的特点是借助西门子S600系统强大的数据处理和控制能力,采用时间记录和能量测量相结合的方法进行计费,具有实时监测和定时输出报表功能.该系统计量准确、计费合理、安全可靠、性价比高,满足了现代物业管理的需要.     

AC—600反应堆压力容器设计探讨

本文根据 ALWR 的基本设计原则,初步分析了我国 AC-600反应堆压力容器的设计特点,探讨了保证 AC-600反应堆压力容器的可靠性应采取的主要技术措施.     

WDB620高强钢应用于大型蜗壳的焊接制造工艺研究

2005年初,水电十四局承担了漫湾二期水电站和小湾水电站蜗壳的制造任务。蜗壳钢材选用国产600 MPa级别高强钢,为了全面综合地考核该级别钢种的材料强度和安全裕度,检验模拟大型蜗壳焊接制造工艺的可靠性。对国产的WDB620高强钢进行了可焊性和制造工艺性试验研究,并在国内首次设计、制造模拟压力容器并对其进行水压试验和爆破试验。研究成果通过中国水电集团公司鉴定,结论为该课题研究成果达到国内选进水平。     

钒微合金Φ25 mm热轧左旋带肋钢筋的研制与生产

通过对热轧左旋带肋钢筋(HRBL600)的质量特性分析,制定了热轧左旋带肋钢筋的化学成分,孔型设计方案和生产工艺.生产实践证明该产品开发获得成功,产品质量达到标准要求.     

钒微合金Φ25mm热轧左旋带肋钢筋的研制与生产

通过对热轧左旋带肋钢筋（HRBL600）的质量特性分析,制定了热轧左旋带肋钢筋的化学成分,孔型设计方案和生产工艺。生产实践证明：该产品开发获得成功,产品质量达到标准要求。     

Water flux,DSC, and cytotoxicity characterization of membranes of cellulose acetate produced from sugar cane bagasse,using PEG 600

Summary In this article, cellulose acetate produced through the homogeneous acetylation of sugar cane bagasse cellulose was used to produce membranes, using poly(ethyleneglycol) 600 (PEG 600) as an admixture. The membranes were characterized using water flux measurements (Payne’s cup), differential scanning calorimetry (DSC) and neutral red uptake (cytotoxicity). The results showed that PEG 600 acts as a crystallinity inductor and/or pore former in the cellulose acetate matrix. The induction of crystallinity is important for this system since it had not been reported on the literature yet. The results also demonstrated that the studied membranes present a nontoxic behavior.     

PEG-6000促进下合成安息香反应研究

以VB1为催化剂,加入辅助剂PEG-6000,顺利合成了安息香,结果表明:安息香产率高,实验重现性好,成功率达100％。     

600MW超临界燃煤机组SCR烟气脱硝工程实例

介绍了国电铜陵600 MW超临界燃煤机组安装脱硝装置项目的前期研究、主要设计特点、系统设计、调试运行,以及投产运行后的经济情况,得出了一系列火电项目加装脱硝设施建设与运行方面的参考意见.     

固溶处理对Ti-600高温钛合金蠕变性能的影响

研究了固溶处理温度和随后的冷却方式对Ti-600高温合金蠕变性能的影响。结果表明,为了获得最佳的抗蠕变性能,宜采用相变点以上的温度进行固溶及随后空冷的处理制度,合金在600℃、150MPa条件下进行蠕变变形,主要受晶界滑动和晶内位错的滑移和攀移所控制。     

Caustic stress corrosion cracking of alloys 600 and 690 with NaOH concentrations

In order to evaluate the stress corrosion cracking resistance for commercial alloys (C600MA, C600TT, C690TT) and Korean-made alloys (K600MA, K690TT), C-ring tests were performed in a caustic environment of 4, 10, 20, 30, and 50% NaOH solution at 315°C, for 480 h with an applied potential of 125 mV vs. OCP. Different stress corrosion cracking phenomena were observed according to the NaOH concentration. The rate of caustic IGSCC attack did not appear to increase monotonically with caustic concentrations, but peaked at a concentration between 4 and 50% caustic, or approximately 30% NaOH. Intergranular stress corrosion cracking was found for C600MA in 10, 20, and 30% NaOH solutions, while no cracking was observed in the 4 and 50% NaOH solutions. In 30% NaOH solution, transgrnular stress corrosion cracking was detected in C690TT, which may be related with the large amount of plastic strain (150% yield) and the applied potential (125 mV vs. OCP). The overall data clearly indicate that C600MA has the worst SCC resistance while K690TT offers the best resistance. There is also fairly good correlation between the caustic SCC susceptibility and some metallurgical parameters, particularly the grain size and the yield strength at room temperature. Specifically, materials having larger grain size and lower yield strength exhibited higher caustic SCC resistance.