不同海拔高度下γ射线空气衰减系数的计算

在航空γ剂量率测量过程中由于海拔高度跨度大，γ射线空气衰减系数会受到海拔高度、温度、气压与空气密度的影响，故需要进行相应修正。利用蒙特卡罗（MCNP）法模拟γ射线在不同空气密度下的线衰减系数。利用经验公式计算不同海拔高度下的空气密度，利用MCNP法建立γ谱仪模型，计算不同海拔高度、不同密度条件下的γ光子注量，根据指数衰减原理计算不同空气密度下的线衰减系数。结果表明，由经验公式求出的空气密度模拟得出的空气质量衰减系数与美国NIST推荐值最大相对误差为-17.3%；在γ射线参考辐射场中用衰减板进行实验验证，⁶⁰Co源的最大相对误差为6.0%，¹³⁷Cs源的最大相对误差为5.3%。本工作为后续低空近地辐射剂量的研究工作奠定了基础。     

Simultaneously achieving high energy-storage density and power density under low electric fields in NBT-based ceramics

Aiming at the problem that power density and energy density are difficult to obtain simultaneously under low field, a novel composition (1-x)Na_0·5Bi_0·5TiO₃-xBaZn_1/3Ta_2/3O₃((1-x)NBT-xBZT) was designed and fabricated via solid-state methods. With the addition of BZT, the crystal lattice, structural symmetry, grain size, and dense degree were all increased proved by XRD, Raman, and Archimedes drainage method et al. Because of the enhancement of relaxor behavior, the x=0.10 sample displayed a high permittivity ε_r of 2871±15% and a low dielectric loss tan δ ≤ 0.025 in the wide temperature range of 60–400 ^oC. This ceramic also showed maximum recoverable energy density W_d (2.07 J/cm³) with high efficiency η (71.5%) under a low field of 150 kV/cm. Moreover, pulse discharge testing proved that this ceramic possessed both a significant discharge energy density W_D (0.96 J/cm³) and a record high power density P_D (108.54 MW/cm³). This work provided a promising material for high power and energy applications.     

5A06-O aluminium–magnesium alloy sheet warm hydroforming and optimization of process parameters

The uniaxial tensile test of the 5A06-O aluminium–magnesium (Al–Mg) alloy sheet was performed in the temperature range of 20–300 °C to obtain the true stress–true strain curves at different temperatures and strain rates. The constitutive model of 5A06-O Al–Mg alloy sheet with the temperature range from 150 to 300°C was established. Based on the test results, a unique finite element simulation platform for warm hydroforming of 5A06-O Al–Mg alloy was set up using the general finite element software MSC.Marc to simulate warm hydroforming of classic specimen, and a coupled thermo-mechanical finite element model for warm hydroforming of cylindrical cup was built up. Combined with the experiment, the influence of the temperature field distribution and loading conditions on the sheet formability was studied. The results show that the non-isothermal temperature distribution conditions can significantly improve the forming performance of the material. As the temperature increases, the impact of the punching speed on the forming becomes particularly obvious; the optimal values of the fluid pressure and blank holder force required for forming are reduced.     

A two-dimensional air streamer discharge modified model based on artificial stability term under non-uniform electric field at low temperature and sub-atmospheric pressure

In this paper, an improved air discharge fluid model under non-uniform electric field is constructed based on the plasma module COMSOL Multiphysics with artificial stability term, and the boundary conditions developed in the previous paper are applied to the calculation of photoionization rate. Based on the modified model, the characteristics of low temperature subatmospheric air discharge under 13 kV direct current voltage are discussed, including needle-plate and needle-needle electrode structures. Firstly, in order to verify the reliability of the model, a numerical example and an experimental verification were carried out for the modified model respectively. Both verification results show that the model can ensure the accuracy and repeatability of the calculation. Secondly, according to the calculation results of the modified model, under the same voltage and spacing, the reduced electric field under low temperature subatmosphere pressure is larger than that under normal temperature and atmospheric pressure. The high electric field leads to the air discharge at low temperature and sub atmospheric pressure entering the streamer initiation stage earlier, and has a faster propagation speed in the streamer development stage, which shortens the overall discharge time. Finally, the discharge characteristics of the two electrode structures are compared, and it is found that the biggest difference between them is that there is a pre-ionization region near the cathode in the needle-needle electrode structure. When the pre-ionization level reaches 10~(13) cm~(-3), the propagation speed of the positive streamer remains unchanged throughout the discharge process, and is no longer affected by the negative streamer. The peak value of electric field decreases with the increase of pre-ionization level, and tends to be constant during streamer propagation. Based on the previous paper, this paper constructs the air discharge model under non-uniform electric field, complements with the previous paper, and forms a relatively complete set of air discharge simulation system under low temperature and sub atmospheric pressure, which provides a certain reference for future research.     

电磁场与电磁波课程思政教学改革探索与实践

课程思政作为思想政治理论课程的有效补充，是落实立德树人根本任务的重要组成。《电磁场与电磁波》是物理、电类等专业的重要专业基础课程，深入挖掘其课程思政元素,能够发挥专业课程的隐性育人作用，实现知识传授、能力培养与价值引领的有机融合，对于理工科专业课进行课程思政改革具有现实指导作用。     

温度对核电站传热管阵列声透射特性的影响

为了研究温度分布对于管阵列结构中的声透射特性的影响，以核电站的实际工况为背景，构建了不同的温度场以及周期性变化的非均匀温度场，利用有限元方法进行数值模拟。结果表明：（1）温度分布会改变管阵列声透射频谱的“禁带”宽度以及中心频率位置。在同一介质中，温度变化对频率较高位置的影响大于频率较低的位置。（2）在同样为10℃的温度差下，当水的平均声速为1 653 m·s^-1、饱和水蒸气的平均声速为522.5 m·s^-1时，介质为水时的禁带宽度及中心频率位置变化较大，即声速大的介质的频谱对于温度的变化更敏感。（3）当温度差在10℃以内，在周期性变化的非均匀温度场和与均匀温度场中管阵列声透射特性在第一中心频率23 996.1 Hz之前，两频谱差别很小，在第一禁带之后会出现明显区别。该研究成果对完善核电站应用的声学检测提供了理论基础。     

Gyrotactic microorganisms bioconvection in combined convective magnetohydrodynamic Casson nanofluid flow over a vertically surfaced saturated porous media with variable viscosity

The current article focuses on mass and thermal transfer analysis of a two-dimensional immovable combined convective nanofluid flow including motile microorganisms with temperature-dependent viscosity on top of a vertical plate through a porous medium, and a model has been developed to visualize the velocity slip impacts on a nonlinear partial symbiotic flow. The governed equations include all of the above physical conditions, and suitable nondimensional transfigurations are utilized to transfer the governed conservative equations to a nonlinear system of differential equations and obtain numerical solutions by using the Shooting method. Numerical studies have been focusing on the effects of intricate dimensionless parameters, namely, the Casson fluid parameter, Brownian motion parameter, thermophoresis parameter, Peclet number, bioconvection parameter, and Rayleigh number, which have all been studied on various profiles such as momentum, thermal, concentration, and density of microorganisms. The concentration boundary layer thickness and density of microorganisms increased as the Casson fluid parameter, Brownian and thermophoresis parameters increased, whereas the bioconvection parameter, Peclet number, and Rayleigh number increased. The thermal boundary layer thickness, concentration boundary layer thickness, and density of microorganisms all decreased. The velocity distribution decreases as the Peclet number, bioconvection, and thermophoresis parameters rise but rises as the Rayleigh number, Brownian motion parameter, and Casson fluid parameter rise. These are graphed via plots along with divergent fluid parameters.     

抑霜型空气源热泵机组应用实测研究

空气源热泵结霜过程会恶化机组的实际运行性能，重霜工况下尤为严重，发展抑霜型空气源热泵是保障其高效适用和良性发展的关键。本文依托四川省康定市的某住宅示范工程，开展抑霜型空气源热泵和常规型空气源热泵的现场实测研究，研究抑霜型空气源热泵实际应用中的抑霜、制热性能表现，并进行技术经济性分析。结果表明：抑霜型空气源热泵抑霜效果显著，制热性能得到显著改善，能效提升达到21%~37.3%，费用年值比常规空气源热泵降低了13%，1年左右即可回收追加的投资，具有更好的技术经济性，有助于空气源热泵技术在严重结霜气候区域的高效应用。     

Magnetic field-enhanced photocatalytic nitrogen fixation over defect-rich ferroelectric Bi2WO6

Photocatalytic N₂ fixation is a promising and sustainable manufacturing process of ammonia (NH₃); however, the NH₃ production rate by this method is very low, thus severely restricting further application of this sustainable technology. Therefore, developing an efficient photocatalyst for N₂ fixation under mild conditions is urgently required. Herein, ferroelectric Bi₂WO₆ materials with different surface oxygen defects were prepared, and the concentration of corresponding defects was controlled by adjusting the thermal reduction time. The abundant oxygen defects in Bi₂WO₆ can provide more reactive sites to promote the effective adsorption of N₂, and the photogenerated charge carrier can be efficiently separated benefiting from the internal electric field. These would weaken the N₂ triple bond and reduce the activation energy barrier for the conversion of N₂ to NH₃ under mild conditions. In the absence of sacrificial agents and cocatalysts, the optimized Bi₂WO₆ with oxygen defects shows an indigenous NH₃ yield of 132.175 μmol·g^-1·L^-1·h^-1, which is more than two times higher than that of the original Bi₂WO₆. Surprisingly, the Bi₂WO₆ with oxygen defects produced more than eight times NH₃ (471.13 μmol·g^-1·L^-1·h^-1) than that of the original Bi₂WO₆ when assisted by an external magnetic field, thus providing a new perspective for further enhancing the N₂ fixation performance.