GJB712A-2001航天用GH4169高温合金锻制圆饼规范介绍

介绍了GH 4 16 9高温合金锻制圆饼规范的修订内容 ,对其主要技术指标作了简要说明 ,并与国外同类标准进行了比较。     

Ca,Mg对镍基高温合金力学性能和热塑性的影响

本文研究了单加或同时添加微量Ca和Mg对变形及铸态镍基高温合金力学性能和热塑性的影响。试验表明,适量的Mg或Ca、Mg对提高合金的持久断裂寿命、高温拉伸塑性以及改善热塑性都取得良好效果。     

Thermal—Mechanical Fatigue Behavior and Life Analysis of Cast Ni—base Superalloy K417

In-phase(IP) and out-of-phase(OP)thermal-mechanical fatigue(TMF) behavior of cast Ni-base superalloy K417 was studied.All experiments were carried out under total strain control with temperature cycling between 400-850℃.Both in-phase and out-of-phase TMF specimens exhibited cyclic hardening followed by cyclic softening at the minimum temperature.Besides,they cyclically hardened in the early stage of life followed by cyclic softening at the minimum temperature.Besides,they cyclically hardened in the early stage of life followed by cyclic softening at the maximum temperature.OP TMF life was longer than of IP TMF.Various damage mechanisms operating in different controlled strain ranges and phasing were discussed.A few life prediction methods for isothermal fatigue were used to handle TMF fatigue and their applicability to superalloy K417 was evaluated.The SEM analysis of the fracture surface showed that transgranular fracture was the principal cracking mode for both IP and OP TMF.Oxidation was the main damage mechanism in causing shorter fatigue life for IP TMF compared with OP TMF.     

铸造镍基K3合金的激光熔覆开裂及工艺研究

研究了铸造镍基Ｋ３合金的激光熔覆过程，分析了原始组织及激光熔覆工艺参数对熔覆裂纹形成的及作用；探讨了使用激光熔覆技术对损伤的Ｋ３合金叶片进行修复的可能性。研究结果表明，Ｋ３合金中沿界分布的低熔点共晶及碳化物是引起激光熔覆开裂的主要因素，采用较高的功率密度和较快的扫描速度进行激光熔覆，可减少热影响区范围，明显地抑制熔覆裂纹的产生。     

高温合金材料在铝电解工业中的应用探讨

对高温合金在铝电解工业用作惰性金属阳极材料的选择进行阐述，并就实际应用过程中的抗氧化耐腐蚀性进行探讨；阐述适用于铝电解工业的惰性阳极合金所应具备的必要条件和必须解决的问题，并介绍目前有关的研究动态和研究方向。     

定向结晶时高温合金组织控制的工艺前景EI

报道了俄国航空材料研究院(ВИАМ)在定向单晶高温合金组织控制方面的最新研究成果,例如,利用高速定向结晶工艺创造具有单晶组织的宽弦叶片,以及制造前后缘为规定位相的单晶,而在叶身中部为细柱状定向结晶组织的复合组织叶片。这些新工艺提高了材料的工作能力和发动机寿命。     

冶炼工艺对GH871合金涡轮盘韧性的影响

研究了AIM ESR和VIM ESR两种冶炼工艺对GH871合金涡轮盘三种韧性指标的影响,结果表明:冶炼工艺对该合金在室温、650℃拉伸和缺口冲击韧性影响较小,采用VIM ESR冶炼工艺可以显著提高GH871合金在700℃拉伸韧性和I型裂纹平面应变的断裂韧性。     

Crack initiation and propagation induced by inclusions in a nickel-base P/M superalloy under fatigue load

1 IntroductionRecently the key components in advanced aircraftengines are widely made of nickel-base P/M super-alloy. However, non-metallic inclusions are intro-duced into this material during powder metallurgyprocessing. In industry, although many method…     

单晶高温合金定向凝固过程中初生碳化物的上浮现象SCIEI

本文在一种抗热腐蚀单晶镍基高温合金平面及胞状液-固界面定向凝固条件下,发现了初生碳化物(TiC)的上浮现象并分析了其形成原因。     

高温精炼处理对铸造镍基高温合金组织与性能的影响

研究了高温精炼处理对铸造镍基高温合金组织与性能的影响.普通铸造镍基合金枝晶组织粗大,晶界碳化物呈链状分布,晶内碳化物呈草体汉字状密集分布于枝晶间,是合金塑性低的主要原因.经高温精炼处理后,合金的枝晶组织细化,晶界及枝晶间的碳化物数量减少,γ γ共晶相数量增加,晶界碳化物呈不连续质点状分布,晶内碳化物的密集程度下降,拉伸塑性和蠕变(持久)寿命得以明显提高.经1 650℃,5 min高温熔体处理后,合金室温延伸率由3.5%提高到9.2%,700℃高温塑性由2.0%提高到8.0%,900℃高温塑性由2.8%提高到9.6%,蠕变寿命由34 h提高到52 h,蠕变塑性由4.3%提高到6.11%.推荐的最佳高温精炼处理制度为1 650℃保温4 h.分析了高温精炼处理对合金液态结构、凝固组织与性能的影响机理.