Etching technique for revelation of plastic deformation zone in low carbon steel

Abstract

In this study, an etching technique to detect the localised plastic deformation behaviour in a low carbon steel was developed. With this technique, etching with Fry solution under ultrasonic vibration was carried out on samples plastically deformed and then heated at 550°C for a certain period of time. The plastic zone was revealed by different degrees of etching in the plastically deformed and non-deformed regions; the plastic zone was found to be only slightly etched, whereas the other region was deeply etched. From the surface offset after etching, the deformation zone was found to be observable even at low magnification, such as 10 times. As the heating duration increased, the plastic zone became clearer. The mechanism for such an etching reaction is discussed on the basis of electrochemical analysis.     

Effects of heat treatment processes on microstructure and properties of 2·25Cr–1Mo–0·25V HSLA steels

Abstract

In the present paper, the effects of the heat treatment processes with two conditioning treatments and four quenching–tempering processes on the mechanical properties of 2·25Cr–1Mo–0·25V high strength low alloyed (HSLA) steel are investigated. The results show that the conditioning treatments have obvious effects on the low temperature impact energy but little effect on the tensile strength. The elevation of the final austenitising temperature increases the strength, whereas it results in the decrease in the low temperature impact energy due to the coarse microstructure. The results of the fracture surfaces analysis further make sure that the fracture surfaces of tensile specimens all exhibit ductile characters with a lot of dimples. However, the fracture surfaces of impact specimens exhibit two typical fracture characters, i.e. the ductile and brittle fracture surface corresponding to the fine and coarse microstructures respectively. In addition, the elongation and reduction in area seem to be insensitive to the heat treatments. Meanwhile, the impact fracture mode is more sensitive to the grain size and not to the low temperature impact energy.     

Development of process for thermomechanical treatment of ultrahigh strength steel prepared by electroslag refining

Abstract

Thermomechanical treatment (TMT) is the simultaneous use of work hardening, and grain refinement along with solid solution and precipitation strengthening. In this investigation, four alloys, with a base composition of 0·28%C, 1·0%Mn, 4·2%Cr, 1·0%Mo, 0·34%V, were prepared by electroslag refining (ESR) and by addition of small amounts of Ti and Nb and by increasing Cr and V to 4·8 and 0·48% respectively. In two of the alloys a yield strength in excess of 1550 MPa was obtained in the as cast quenched and tempered condition. Attempts were made to further increase the yield strength by thermomechanical treatment. The process parameters for thermomechanical treatment were optimised by adopting procedures such as calculation of stability of precipitates, hot compression test, determination of cooling rates in different coolants, and modelling of TTT and CCT diagrams. The process involved prerolling of the ESR ingot to a bar at 1200°C, followed by hot rolling in two passes starting from 950°C and finishing at 850°C with equal deformation of 25% in each pass to convert the bar into plates. These were immediately cooled in one of the cooling media: air, polymer–water solution (1 : 1·5) and oil. Yield strength in excess of 1750 MPa was obtained in oil cooled specimens of the alloy with titanium addition and that where Cr and V were increased. The niobium added specimen gave strengths, similar to that obtained for the base alloy, in spite of the fact that the as cast alloy had shown very high strengths, presumably because of the high soaking temperatures and grain growth. Air cooling gave the lowest strengths and oil cooling the highest.     

Characterisation of severely deformed austenitic stainless steel wire

Abstract

The microstructure of 8 μm diameter wire produced by the severe deformation of 316L austenitic stainless steel has been examined using TEM and X-ray diffraction. The deformation imparted amounts to a true strain of 6·3. Data from previous studies on strain induced transformation of this steel have been combined with new results to show that true strains >2 are required in order to observe mechanical stabilisation, i.e. the cessation of martensitic transformation when the martensite/austenite interfaces are unable to propagate through the dislocation debris created in the austenite.     

A model based creep equation for 9Cr–1Mo–0·2V (P91 type) steel

Abstract

The isothermal constant stress creep tests data for a 9Cr–1Mo–0·2V (P91 type) steel were submitted for a phenomenological analysis in order to obtain the relevant creep equation for such steel. Namely, the minimum creep strain rate of P91 type steel cannot be described by the simple Arrhenius type power law constitutive model. The incorporation of the threshold stress concept in the analysis of creep data leads to a modified power law, which satisfactorily describes the creep behaviour of the examined P91 steel. However, the threshold stress is not a good material parameter, as it often varies with temperature and/or applied stress. This adds uncertainty to the extrapolation of the creep rates into ranges where experimental data are not available. Besides the fact that the physical foundation for a threshold stress is questionable from a scientific point of view, this is a serious practical limitation of the modified power law creep equation. The second creep equation proposed in the present paper is the improved stress dependent energy barrier model. The improvement of the standard model is based on two assumptions: first, on the hypothesis that the application of a stress also affects the energy barrier to be overcome when a local region transitions from the initial to the final state, and second, by applying a simple power function of stress instead of a hyperbolic sin function in the model based equation. The obtained value of stress exponent, n=5·5, is too high for entirely climb controlled creep. The apparent activation energy of approximately 510 to 545 kJ mol^?1, which is considerably higher than the activation energy for lattice diffusion, is the stress dependent activation energy of the slowest, dominant rate controlling process of the supposed multiple creep mechanisms.     

New viscoplastic model to simulate hot isostatic pressing

Abstract

Most of the numerical simulation software on the hot isostatic pressing (hipping) process is based on viscoplastic modelling of densification, such as the well known Abouaf's model. These constitutive equations are generally obtained from a viscoplastic potential depending on Green's equivalent stress. An implicit coupling between isotropic and deviator parts is therefore only defined by an equivalent stress. A new viscoplastic formulation proposed by Stutz introduces an explicit coupling between isotropic and deviator parts of the stress state, allowing then more flexibility to take into account the experimental results achieved from isotropic, die compaction, and creep tests. This paper deals with the presentation of this new formulation which has been implemented in the finite elements software PreCAD, and the subsequent changes observed in numerical simulations. These simulations achieved with PreCAD software, are compared with an experiment on a complex part manufactured by CEA Grenoble.     

Reactive sintering in Fe-Co system

Abstract

Low porosity powder metallurgy compacts have been manufactured from treated elemental iron and cobalt powders sintered at 1150°C under an H_2(g) atmosphere. Their microstructures consist of an interconnected mixed oxide network which encapsulates both the iron and cobalt phases. The production technique employed is an innovative process termed reacto-thermitic sintering (RTS), which leads to near full density and near net shape parts utilising conventional uniaxial compaction and mesh belt furnace practices. The RTS technique relies on microscale exothermic reaction between small quantities of added elemental Al and oxides present on the surface of the bulk powder, together with the bulk powder itself. This results in the production of a transient liquid phase which freezes rapidly and consolidates the compact without slumping. In order to generate an interconnected mixed oxide network, experiments were designed such that the Al powder reacts with the cobalt and the surface of the iron powder which is artificially doped with Fe and Cr oxides.

Differential thermal analysis (DTA) and energy balance calculations revealed that the Al and the oxide coating reaction does not proceed directly. Instead the main contribution to the exothermic process is the reaction between Al and Co/Fe. The system does not exhibit true RTS behaviour and the interconnected network of mixed Al, Cr, and Fe oxides is created by subsequent reaction of Co-Al and Fe-Al intermetallics with the artificial Fe-Cr oxide coating on the Fe. The microstructure obtained exhibits negligible porosity with the metallic particles on the whole fully encapsulated by the oxide.     

Substitution of graphite in powder metallurgical steels with carbon from petroleum products

Abstract

This paper reviews the mechanical and microstructural characteristics of hypoeutectoid steels obtained by powder technology, in which various carbonaceous petroleum products provide the carbon constituent. These steels are compared with others of similar composition obtained from graphite.     

Optimised running system design for bottom filled aluminium alloy 2L99 investment castings

Abstract

This research has evaluated the effect of surface turbulence introduced during the filling of moulds on the reliability of Al-7Si-Mg alloy (2L99)investment castings. Four different running systems were designed to provide different amounts of surface turbulence: top filled, uncontrolled bottom filled, and controlled bottom filled with and without a filter. Computer modelling has been used to simulate the filling of the different designs and the results have been compared with the actual flow behaviour established using real time X-ray radiography. Castings have been produced using the different running systems, tested in four point bending, and the results analysed using the Weibull statistical technique. It has been shown that top filling produces significant turbulence, which results in the least reliable castings (Weibull modulus of 25.5). There was no significant difference between this and the Weibull modulus of 27 found for uncontrolled bottom filled systems. This indicates that a poorly controlled bottom filled system is no better than a top filled system. Both were inferior to the controlled bottom filled systems without and with filters, which had Weibull moduli of 38 and 54 respectively. SEM examination and oxygen analysis of representative fracture surfaces has provided supporting evidence for the important role that oxide films played in reducing properties.     

New method to prepare iron particles with different morphologies: a way to get high green strength metal compacts

Abstract

Metaliron powders of well controlled size and morphology were synthesised by thermal decomposition under hydrogen of precipitated ferrous oxalates. Green compacts were prepared by uniaxial pressing of metal powders at 290 MPa. The bending green strengths of compacts were measured.

The precipitation of β-FeC₂O₄.2H₂O oxalate from ammonium oxalate gives rise to the formation of spherical particles by aggregation ofelongated grains. Thermal decomposition of this oxalate from 400 to 500°C under hydrogen permits metal iron particles with a rough surface to be obtained. Decomposition occurring above 500°C induces a smoothness of the particle surface. Metal particles synthesised at 500°C show both surface roughness and micrometer sized primary grains.This specific microstructure has allowed the highest value ofcompact green strength (31·7 MPa) to be obtained.

Acicular shaping of the β-FeC₂O₄.2H₂O particles precipitated from oxalic acid involves, after decomposition, an increase in the surface roughness and shape irregularity of the metal particles, owing to an entanglement of the elementary grains. An exceptional value (about 60 MPa) for the metal compact green strength was thus obtained for this type of powder.