梯恩梯-吉纳、地恩梯-太安装药体系自旋爆轰特性的研究

本文研究了梯恩梯-吉纳(TNT-DINA)和地恩梯-太安(DNT-PETN)体系的自旋爆轰现象,爆轰波是以低频脉冲方式传播.这些体系具有的爆速、爆热分别为DJ=7.3～7.4km/s和Qv=(5.40±0.01)MJ/kg.不同组成的爆速和爆压PJ通过SW程序计算.用扩散区的爆压P3和爆温T3来评估爆轰波的衰减和重新点火.敏化剂含量相同,梯恩梯-黑索金(TNT-RDX)体系的爆压PJ大于TNT-DINA的爆压,TNT-RDX体系的温度T3比TNT-DINA高60～100K.计算值与实验结果吻合较好.     

含RDX的硝胺丁羟推进剂能量特性研究

采用最小自由能平衡流法对RDX/AP/Al/HTPB推进剂能量特性进行了理论计算。通过BSF165mm和BSF315mm发动机点火试验,研究了RDX含量、燃烧室压强对RDX/AP/Al/HTPB推进剂能量特性的影响规律。根据理论计算和发动机试验结果,对配方进行了优化设计,与某型号760mm全尺寸发动机的实测结果对比,其实测比冲高达2428.1N·s·kg-1(pc=6.86MPa),验证了RDX的加入对RDX/AP/Al/HTPB推进剂比冲有较突出贡献。     

Condensed combustion products of aluminized propellants. IV. Effect of the nature of nitramines on aluminum agglomeration and combustion efficiency

The condensed combustion products of two model propellants consisting of ammonium perchlorate, aluminum, nitramine, and an energetic binder were studied by a sampling method. One of the propellants contained HMX with a particle size D ₁₀ ≈ 490 μm, and the other RDX with a particle size _{D 10} ≈ 380 μm. The particle-size distribution and the content of metallic aluminum in particles of condensed combustion products with a particle size of 1.2 μm to the maximum particle size in the pressure range of 0.1–6.5 MPa were determined with variation in the particle quenching distance from the burning surface to 100 mm. For agglomerates, dependences of the incompleteness of aluminum combustion on the residence time in the propellant flame were obtained. The RDX-based propellant is characterized by more severe agglomeration than the HMX-based propellant — the agglomerate size and mass are larger and the aluminum burnout proceeds more slowly. The ratio of the mass of the oxide accumulated on the agglomerates to the total mass of the oxide formed is determined. The agglomerate size is shown to be the main physical factor that governs the accumulation of the oxide on the burning agglomerate. __________ Translated from Fizika Goreniya i Vzryva, Vol. 42, No. 4, pp. 78–92, July–August, 2006.     

黑索今制备过滤过程中的特性与安全性?

为分析黑索今(RDX)制备过滤工艺中的特性和安全性,以一定固含量的RDX-水悬浮液为物料,模拟RDX生产的过滤过程,通过测试RDX静态恒定压差下的过滤时间所对应的滤液流量,得到了不同操作条件下的过滤常数K和滤饼压缩性指数s,并讨论了过滤条件对过滤特性的影响。结果表明,过滤常数K值随介质厚度的减小、过滤压力和介质孔径的增大而增大,RDX滤饼属中、轻度压缩材料。结合RDX静态和动态过滤过程中滤饼含湿量变化规律,对过滤过程的安全性进行了分析,结果表明,过滤工序的操作安全性明显高于干燥工序。     

RDX基复合物静电喷雾法制备及性能研究

采用静电喷雾技术制备了以氟橡胶(F2604)、聚乙烯醇缩丁醛(PVB)及三硝基甲苯(TNT)为包覆材料的黑索今(RDX)基复合颗粒,对所制备的复合颗粒进行扫描电镜(SEM)、傅里叶变换红外光谱(FTIR)、X射线衍射(XRD)和差示扫描量热仪(DSC)分析,得到超细包覆粒子的包覆效果及其热分解特性。结果表明:F2604/RDX与PVB/RDX复合颗粒为形貌规整、粒径均一的球形颗粒,而TNT/RDX复合颗粒为不规则多面体;F2604/RDX、PVB/RDX与TNT/RDX复合颗粒的红外吸收峰和X射线衍射峰位置与RDX一致;PVB/RDX复合物活化能最低,为137.059 k J/mol。     

DFT与OFF相结合的RDX分子设计

RDX是环三甲撑三硝胺的简称,又名黑索金.是军民领域常用的高能炸药.生成焓是炸药的基本热力学性质,是其含能高低的标志,从理论上计算分子结构并预测其生成焓对含能材料的分子设计和品优炸药的筛选具有重要意义.在众多计算方法中,DFT采用大型基组计算目标分子的全电子,结果精确,可信度高,缺点是需时长,耗费计算资源;基于半经验法的从头算法是对Hartree-Fock方程的近似求解,耗费机时少,但结果可信度低;分子力场(OFF)基于牛顿经典力学,以原子间的相互作用势函数(或称力场)来描述分子内和分子间的作用力,计算速度非常快,可计算大分子或高分子材料的物理性质,但在计算分子结构方面效果不太理想.本文用密度泛函理论(DFT)与开放力场(OFF)相结合的方法,计算高能炸药--黑索金(RDX)的分子结构和气相生成焓,在保证计算精度的同时节约了时间.在构象搜索阶段,分别采用分子力学(MM)和分子动力学(MD)方法,实现对目标分子的结构驰豫和模拟退火,在分子的几何结构优化阶段,则采用DFT GGA-BLYP法.分析优化RDX分子的键长与键角表明,RDX分子结构的计算结果与实验测定基本吻合.设计反应路径,并利用DFT GGA-BLYP计算出RDX的气相生焓为188.604 kJ/mol,与实验测定值191.444 kJ/mol接近.     

Desorption characteristics of uncoated silicon microcantilever surfaces for explosive and common nonexplosive vapors

We measured the desorption of explosive trinitrotoluene (TNT), pentaerythritol tetranitrate (PETN), and hexahydro-1,3,5-triazine (RDX) vapors from piezoresistive silicon microcantilevers under ambient air. Depending on the amount of vapor loaded on the cantilever, TNT desorption took a few minutes to tens of minutes (for nanogram quantities). On the other hand, no significant loss of PETN or RDX was observed after many hours. We also measured desorption of common “nonexplosive” compounds (water, acetone, and ethyl alcohol) and observed that desorption was too fast to be measured. There is a good correlation between the desorption time and the melting point (or the vapor pressure) of a particular substance. In principle, this method can be used to measure desorption rates of various substances from cantilever surfaces.     

Particle size reduction of RDX by sequential application of solvent–antisolvent recrystallization and mechanical methods

ABSTRACT

Solvent–antisolvent recrystallization produced ~8 µm average size RDX particles (UF-RDX) that were subsequently subjected to mechanical methods of ultrasonication and ball-milling to find further achievable reduction in particle size. Long duration ultrasonication for 20 h and 300 rpm ball milling for 4 h of UF-RDX decreased its average particle size to ~2 µm. RDX produced by all the three processes (solvent–antisolvent recrystallization, ultrasonication and ball-milling) was similar to coarser RDX in structure and thermal decomposition behavior. However, UF-RDX produced by solvent–antisolvent recrystallization was significantly less impact sensitive than that produced by ball-milling and ultrasonication. The issues of residual solvent and the metal contamination during RDX processing were addressed by process parameter optimization. Solvent–antisolvent recrystallization and mechanical methods even when used sequentially could not bring average particle size of RDX to nano-scale.     

FOX-7和RDX基含铝炸药的冲击起爆特性

为研究FOX-7和RDX基含铝炸药的冲击起爆特性,对其进行了冲击波感度试验和冲击起爆试验,结合冲击波在铝隔板中的衰减特性,确定了FOX-7和RDX基含铝炸药的临界隔板值和临界起爆压力,并通过锰铜压阻传感器记录了起爆至稳定爆轰过程压力历程的变化。结果表明,以Φ40mm×50mm的JH-14为主发装药时,FOX-7和RDX基含铝炸药临界隔板值分别为37.51和34.51mm,对应的临界起爆压力为10.91和11.94GPa;起爆压力为11.58GPa时,FOX-7炸药的到爆轰距离为25.49~30.46mm,稳定爆轰后的爆轰压力为27.68GPa,爆轰速度为8 063m/s;起爆压力为14.18GPa时,RDX基含铝炸药的到爆轰距离为17.27~23.53mm,稳定爆轰后的爆轰压力为17.16GPa,爆轰速度为6 261m/s。     

Fe2O3-Al纳米铝热剂与超细RDX复合物的制备与性能

采用溶胶-凝胶方法,制备出了纳米铝热剂nano-Fe2O3-Al,并获得了其与超细RDX的复合含能材料nanoFe2O3-Al/SFRDX。采用BET法、SEM、XRD综合表征了nano-Fe2O3-Al的结构,采用TG/DSC联用技术测试了nano-Fe2O3-Al的热性能,结果表明气凝胶铝热剂的反应温度更低;nano-Fe2O3-Al的静电火花感度测试结果表明纳米铝热剂对静电十分敏感。对nano-Fe2O3-Al/SFRDX在无约束条件和密闭条件下的燃烧行为进行了研究,高速相机照片法发现在无约束条件下,nanoFe2O3-Al燃烧高达300 m/s,且nano-Fe2O3-Al/SFRDX具有在无约束条件下由燃烧转为爆轰的趋势。