基于软件校准的短波发射机功率控制系统设计

短波发射机功率稳定一直是通信领域致力改善的重点问题,短波发射机功率不稳定会直接影响无线电通信质量,造成通信失真、表达不清晰等问题。针对上述问题,基于软件校准设计短波发射机功率控制系统。该系统借鉴MVC设计模式搭建系统数据库层、业务逻辑层、控制层以及界面显示层基础框架；将功率计与短波发射机相连,实时采集工作状态下的短波发射机功率数据,通过信号处理器实施处理后并存储,借鉴传输元件,将数据发送到控制器,通过控制器校准短波发射机功率与预期之间的偏差,以偏差量为输入,利用改进PID运算得出控制量,生成控制命令,通过输入输出信号接口板输出命令,控制驱动装置调节短波发射机运行参数,实现功率控制。结果表明：与 控制系统、自动调谐系统应用相比较,在所设计系统应用控制下,100s内短波发射机的功率变化曲线与预期曲线之间的拟合优度指数更大,更接近1,优于对比系统,说明相比于对比系统。本系统控制表现更好,更能维持短波发射机功率稳定,达到了研究目标。     

Two-step method to deposit ZrO2 coating on carbon fiber: Preparation,characterization, and performance in SiC composites

Recently, ceramic matrix composites reinforced by short carbon fibers (CFs) attracted increasing attentions. To further improve mechanical properties and oxidation resistances, CFs were subjected to oxidation and acidification followed by sol-gel dip-coating to deposit ZrO₂ on their surfaces. ZrO₂-C_f/SiC composites were fabricated by joint hot compression molding and sintering, compared to C_f/SiC and SiC prepared by the same method. Microstructural analyses indicated that ZrO₂ coatings were successfully deposited on CF surfaces, formed strong bonding and interfaces between CF and the matrix. Meanwhile, CFs were found uniformly distributed in SiC matrix with random orientations. Flexural curves of ZrO₂-C_f/SiC and C_f/SiC revealed the presence of “false plasticity” regions after sharp drops, which were quite different from brittle flexural behavior of SiC ceramic. Compression strength of the three samples showed step-up growth. ZrO₂-C_f/SiC exhibited the highest value, indicating the introduction of CFs and ZrO₂ coatings do have great influence on mechanical performances. After heat treatment, ZrO₂-C_f/SiC exhibited better oxidation resistance than C_f/SiC, with weight loss ratios estimated to ??3.76% and ??6.43%, respectively. These improved properties indicated that ZrO₂-C_f/SiC would be excellent alternatives to other existence materials under ultra-high temperature environments.     

电力变压器动稳定破坏的分析和对策

对大型电力变压器绕组在变压器发生外部短路时所受的辐向力和轴向力进行了分析和计算，比较了国内外不同的计算方法和得出的不同结果。     

预付费用户实现短消息业务的关键技术分析

介绍了目前国内移动智能网系统和短消息系统的现状 ,在此基础上提出了基于移动智能网的预付费用户实现短消息业务的 3种解决方案 ,对各方案进行了分析和比较。最后 ,介绍了CMIN0 2移动智能网系统中预付费短消息业务的实现。     

Hot carrier magnetophonon spectroscopy of semiconductors in high magnetic fields up to 40 T

Hot carrier magnetophonon resonances of n-type Si, short channel InP and p-type InSb were investigated in pulsed high magnetic fields up to 40 T. Using a recently developed high resolution technique in pulsed high fields, many new features of the hot carrier-phonon interactions in high magnetic fields were found.     

浆砌石坝爆破拆除及监测技术

在陕西宝鸡峡引水枢纽浆砌石大坝改建过程中 ,Ⅱ坝段的全部以及Ⅵ坝段的部分须用爆破方法拆除。为了避免爆破震动对相邻的和保留的浆砌石坝体的不利影响 ,利用伸缩缝和预先开挖的沟槽隔震 ,采用了浅孔爆破分层拆除的方法 ,实施微差爆破 ,严格控制最大一段药量。爆破震动监测和声波测试的结果表明 ,保留的浆砌石坝体没有受到损伤     

A methodology for assessing gamebird use of short rotation coppice

Gamebirds provide a considerable incentive to plant and manage new woodlands. The supplementary income thus generated can improve their overall value. Other studies suggest that Short Rotation Coppice (SRC) crops may provide an attractive habitat for some gamebird species and could increase the value of the crop. To investigate this, the use by pheasants and partridge of different types of SRC at one site was assessed.

A method using sand quadrats to record gamebird footprints and hence relative use was developed. Pheasant footprints were recorded more frequently in the quadrats alongside the willow coppice, whereas partridge footprints occurred more frequently alongside the poplar coppice. Footprint analysis offers a reliable method of investigating how gamebirds use different types of SRC within small areas. The results are considered in terms of the placement of short rotation coppice plantations in the landscape to improve their ecological design.     

14 kV single-phase superconducting fault current limiter based on YBCO films

We present the fabrication and short circuit test results of a 14 kV single-phase resistive superconducting fault current limiter (SFCL) based on YBa₂Cu₃O₇ (YBCO) films. Individual components were processed using the 4″ YBCO films and have the rated voltage and current of 600 V and 35 A at 77 K, respectively. Twenty four components, eight components in series and three lines in parallel, make a module having the rated voltage and current of 4.8 kV and 105 A, respectively. Three modules were assembled in series to produce the SFCL working at 77 K, a 14 kV single-phase machine for the 22.9 kV Y-Y grid. short circuit tests were successfully conducted in an accredited test facility with the maximum fault currents up to 14.1 kA_P. All components quenched together upon faults and shared the rated voltage evenly without any supplementary device between the modules. This proves that the SFCL based on YBCO films may not only work reliably at 22.9 kV, but also provide technical feasibility for higher voltage application including the transmission grids.     

缺口状态对SiC/LY12复合材料短裂纹疲劳行为的影响

研究了峰值时效状态下SiC/LY12复合材料及LY12铝合金不同缺口状态下的短裂纹扩展行为,结果表明:在尖缺口及钝缺口状态下,短裂纹扩展均表现出“马鞍”型特征;尖缺口下,SiC不利于材料疲劳性能,钝缺口下,Sic有利于材料疲劳性能;用闭合效应和缺口根部塑性区大小解释了缺口状态对短裂纹扩展的影响.     

INITIAL FRACTURE MECHANISMS IN NICKEL ALLOYED PM STEEL

Abstract— Initial fatigue crack propagation mechanisms at near threshold conditions were studied for four nickel-alloyed, powder-metallurgy (PM) steels. Fatigue fracture surfaces were obtained by testing smooth rectangular specimens at 30 Hz and under constant amplitude and zero mean stress conditions. Materials based on Distaloy AE were used in two densities, namely 7.15 and 7.45 g/cm³.
All the fracture surfaces were composed of three morphological regions (i) a macrocrack initiation region Rl where cracks propagated preferentially through particles (ii) a macrocrack growth region R2 and (iii) an unstable crack growth region R3 where cracks propagated preferentially between particles. Initial fatigue crack growth, in region R1, was controlled by the propagation of short cracks whose dimensions were comparable to the material microstructure. The subsequent fatigue crack growth in regions R2 and R3 was controlled by ductile rupture between microvoids. Transparticle fracture in region R1 was independent of pore distribution, while interparticle fracture in regions R2 and R3 was dependent on pore distribution.