An effective method of bulk materials moisture measurement using capacitive sensors

When we speak about capacitance moisture meters for bulk materials we have to face with different values of dielectric permittivity for different bulk materials in dehydrated state, what causes a method error that can be named ‘type uncertainty’. Besides, different varieties of the same material have different values of dielectric permittivity, which depend from geographical origin, processing conditions etc. It can be hardly predicted automatically and type uncertainty can be compensated only in separate situations with the help of preliminary calibration. Main tasks of the research are to develop new comparison principle of moisture measurement with better accuracy due to effective compensation of physical, chemical and granulometric composition influence on the result of moisture measurement, develop new primary and secondary instrument transducers. Moisture sensor consists of four measuring capacitors. Two of them should be filled with a sample, which moisture content should be determined, and other pair of measuring capacitors should be filled with a same substance, but previously dehydrated. Mathematical models, developed to take into account granulometric composition of a bulk material were used to carry out a comparison analysis for three types of instrument measuring transducers. Obtained results proved that suggested principle of moisture measurement provides effective compensation of granulometric composition influence. Developed measuring principle had been experimentally tested what helped to confirm that it provides two times better compensation of different physical and chemical composition for different materials in comparison with the direct comparison method.     

PZT components derived from polysulphone spinning process

The present paper deals with the development of lead zirconate titanate (PZT) fibres, pearls and fibre fragments, for their use as active phase in piezocomposites. As new a approach, the green ceramic components are shaped by polysulphone spinning, allowing for effective and flexible forming over a wide range of different geometries and sizes. The correlation between processing parameters, e.g. the slurry composition, nozzle size and operation velocity, and the resultant shape of ceramic components is analysed. Sintered piezoceramic parts show a dense microstructure. Performance data are evaluated on PZT/epoxy composites. Measurement results of strain, polarisation and piezoelectric coupling are given and discussed. The developed PZT components are seen as key for the creation of smart and lightweight structural components. Further, free formed PZT components open new design approaches for sensing and actuating devices and ultrasound transducers.     

换能器结构参数对聚合物超声塑化黏弹生热的影响

为研究超声换能器结构参数对聚合物超声塑化过程黏弹性生热的影响，首先确定超声黏弹性生热系统的组成，进行纵振超声换能器结构设计；然后分析超声黏弹性生热过程及超声黏弹性生热原理；最后采用单一变量法分析超声换能器的主要结构参数对其纵振频率及工具头前端质点最大振幅的影响，将其实际输出的纵振激励加载于熔融聚合物，研究其结构参数对聚合物超声黏弹性生热过程及达到聚合物玻璃化转变温度所用时间的影响。结果表明，随纵振激励作用时间的增加，聚合物温度非线性升高；放大比对聚合物温度变化影响最大，前盖板厚度和工具头长度次之，影响最小的是变幅杆长度。     

宽频带梯形叉指式换能器优化设计及应用

由声表面波（Surface Acoustic Wave）器件发展而来的叉指换能器（Interdigital Transducer，IDT）由于其工作频率可以设计、频带宽可调、损耗低等特点逐步应用于结构健康监测（Structural Health Monitoring，SHM）系统中，因此在智能材料与结构中有着广泛的应用前景。本文针对现有矩形IDT带宽窄的不足，研究宽频带梯形叉指换能器（Trapezoidal Interdigital Transducer，TIDT）。采用有限元分析方法对TIDT的尺寸进行结构优化设计，并对设计的TIDT进行性能测试，通过实验研究了TIDT用于结构损伤检测的初步应用。实验结果表明，TIDT在实际应用中进一步提高了损伤识别精度，具有广泛的应用前景。     

基于十字形阵列和2D-MUSIC算法的Lamb波检测

采用由压电传感器组成的十字形阵列进行Lamb波信号的激励和接收，提出一种二维多重信号分类（2D-MUSIC）方法对铝板中的缺陷进行定位检测。选用合适的频率激励产生单一模态信号，可避免多模态的影响，降低Lamb波的频散；利用2D-MUSIC算法对接收信号进行分段处理，并结合反射信号和二维导向矢量对铝板中的缺陷进行定位。结果表明，提出的2D-MUSIC算法对铝板中的缺陷定位比传统MUSIC算法更精准。     

交-交变频器输出波形对称度改造的模糊控制实现

针对在交_交变频器研究中变频器输出电压波形不对称的问题 ,提出用模糊控制方法来进行改造 ,并提供了一套系统的改造方案 ,最后给出实验结果和分析。实验证明 ,用模糊控制方法对采用余弦交截法的变频器输出波形对称度进行改造是行之有效的     

变速恒频双馈风力发电机励磁系统研究

通过几种励磁变频电路的经济性、稳定性和容量等方面比较分析,得出两电平电压型双PWM变换器可以很好地满足交流励磁发电机变速恒频运行的结论,是交流励磁电路的最优方案。     

一种用于低速重载轴承故障诊断的共振解调法

针对低速重载轴承特点 ,提出了适合于低速重载轴承故障诊断的共振解调方法。通过自制的低频加速度传感器拾取了斗轮式堆取料机回转支承滚动轴承的振动信号 ,利用此方法进行了故障诊断 ,诊断结果可靠     

KG4092型矿用压差传感器的研制

矿井压差测量在矿井通风和瓦斯防治工作中有着十分重要的意义，采用半导体压阻效应原理研制的ＫＧ４０９２型矿用压差传感器具有连续检测、数字显示、电信号输出等功能，与煤矿监测监控系统配套工作，可以有效地用于瓦斯抽放管道、矿井风机等场所的气体压差测量及正压、负压测量。