| 工艺参数影响2060铝锂合金搅拌摩擦焊接头的成形规律 |
| |
| 引用本文： | 刘震磊,崔祜涛,姬书得,徐敏强,孟祥晨.工艺参数影响2060铝锂合金搅拌摩擦焊接头的成形规律[J].焊接学报,2016,37(7):79-82. |
| |
| 作者姓名： | 刘震磊 崔祜涛 姬书得 徐敏强 孟祥晨 |
| |
| 作者单位： | 1.哈尔滨工业大学 深空探测基础研究中心, 哈尔滨 150080;沈阳航空航天大学 航空航天工程学部, 沈阳 110136 |
| |
| 基金项目： | 国家自然科学基金资助项目(51204111)；航空科学基金资助项目(2014ZE54021) |
| |
| 摘 要： | 以在航空领域有广泛应用前景的2 mm厚2060-T8 Al-Li合金为研究对象，进行了搅拌摩擦焊对接接头的试验分析，重点研究焊接工艺参数影响焊接接头成形的规律.研究结果表明，呈碗形的焊缝由轴肩作用区与焊核区组成；轴肩作用区的等轴晶的晶粒大于焊核区.当搅拌头的转速为800 r/min且焊接速度为80 mm/min时，焊接接头的表面成形良好且内部无缺陷.与800 r/min，80 mm/min相比，提高旋转频率或降低焊接速度，焊缝表面变得较粗糙；降低旋转频率或提高焊接速度，焊缝内部会出现隧道型缺陷.
|
| 关 键 词： | 搅拌摩擦焊 2060Al-Li合金 成形 缺陷 |
| 收稿时间： | 2016/3/12 0:00:00 |
Effect of welding parameters on joint formation of friction stir welded 2060 Al-Li alloy |
| |
| LIU Zhenlei,CUI Hutao,JI Shude,XU Minqiang and MENG Xiangchen.Effect of welding parameters on joint formation of friction stir welded 2060 Al-Li alloy[J].Transactions of The China Welding Institution,2016,37(7):79-82. |
| |
| Authors: | LIU Zhenlei CUI Hutao JI Shude XU Minqiang and MENG Xiangchen |
| |
| Affiliation: | 1.Deep Space Exploration Research Center, Harbin Institute of Technology, Harbin 150080, China;Faculty of Aerospace Engineering, Shenyang Aerospace University, Shenyang 110136, China2.Deep Space Exploration Research Center, Harbin Institute of Technology, Harbin 150080, China3.Faculty of Aerospace Engineering, Shenyang Aerospace University, Shenyang 110136, China |
| |
| Abstract: | Friction stir butt welding of 2 mm thick 2060 Al-Li alloy sheet was conducted. The effect of welding parameters on joint formation was investigated. The weld presented bowl shape, and consisted of shoulder-affected zone and weld nugget. The equiaxed grain in the shoulder-affected zone was bigger than that in weld nugget. At rotational speed of 800 r/min and travel speed of 80 mm/min, defect-free joint with excellent-formation surface was attained. Compared to 800 r/min of rotational speed and 80 mm/min of travel speed, increasing rotational speed or decreasing travel speed made the joint surface rougher, while decreasing rotational speed or increasing welding speed would generate tunnel defect in the weld. |
| |
| Keywords: | friction stir welding 2060 Al-Li alloy formation defect |
| 本文献已被 CNKI 万方数据 等数据库收录！ |
| 点击此处可从《焊接学报》浏览原始摘要信息 |
|
点击此处可从《焊接学报》下载全文 |
|
