| 塑料药筒结构设计及吹塑成形工艺 |
| |
| 引用本文： | 刘海艳,杨健,姜春茂,娄勇健,张丽娜,周宇杭.塑料药筒结构设计及吹塑成形工艺[J].精密成形工程,2014,6(2):63-66. |
| |
| 作者姓名： | 刘海艳 杨健 姜春茂 娄勇健 张丽娜 周宇杭 |
| |
| 作者单位： | 北方华安工业集团有限公司, 齐齐哈尔 161046;北方华安工业集团有限公司, 齐齐哈尔 161046;北方华安工业集团有限公司, 齐齐哈尔 161046;北方华安工业集团有限公司, 齐齐哈尔 161046;北方华安工业集团有限公司, 齐齐哈尔 161046;北方华安工业集团有限公司, 齐齐哈尔 161046 |
| |
| 摘 要： | 目的解决药筒在射击后退壳故障问题,降低生产成本。方法将钢质药筒改成塑料药筒,并进行了拉伸力学性能检测、合膛性能以及靶场射击试验。结果产品通过了相关性能检测,满足使用要求。结论全面解决了在高膛压条件下射击时,因金属药筒变形而出现半退壳和不退壳状态的故障问题。
|
| 关 键 词： | 塑料药筒 结构设计 成形工艺 性能检测 |
| 收稿时间： | 2014/1/16 0:00:00 |
| 修稿时间： | 3/1/2014 12:00:00 AM |
Structure Design and Molding Process of Plastic Cartridge |
| |
| LIU Hai-yan,YANG Jian,JIANG Chun-mao,LOU Yong-jian,ZHANG Li-na and ZHOU Yu-hang.Structure Design and Molding Process of Plastic Cartridge[J].Journal of Netshape Forming Engineering,2014,6(2):63-66. |
| |
| Authors: | LIU Hai-yan YANG Jian JIANG Chun-mao LOU Yong-jian ZHANG Li-na and ZHOU Yu-hang |
| |
| Affiliation: | The North Hua'an Industrial Group Company, Qiqihar 161046, China;The North Hua'an Industrial Group Company, Qiqihar 161046, China;The North Hua'an Industrial Group Company, Qiqihar 161046, China;The North Hua'an Industrial Group Company, Qiqihar 161046, China;The North Hua'an Industrial Group Company, Qiqihar 161046, China;The North Hua'an Industrial Group Company, Qiqihar 161046, China |
| |
| Abstract: | Objective To solve the shot ejection failure problem of the cartridge, and to reduce the production cost.Methods The steel cartridge was replaced by plastic cartridge, and tested for tensile mechanical properties, bore performance and shooting range. Result The products passed the relevant performance testing, and met the requirements of use.Conclusion A comprehensive solution was developed for the failure of the ejection and incomplete ejection due to the metal cartridge case deformation under the high chamber pressure conditions during shooting. |
| |
| Keywords: | plastic cartridge case structural design molding process performance testing |
| 本文献已被 CNKI 维普 等数据库收录！ |
| 点击此处可从《精密成形工程》浏览原始摘要信息 |
|
点击此处可从《精密成形工程》下载全文 |
|
