|
|||||
|
|
| 履带销轴用1E1158M钢的奥氏体混晶情况 | |
| 引用本文： | 王欢,胡佳丽,张朝磊,李戬,苗红生.履带销轴用1E1158M钢的奥氏体混晶情况[J].钢铁,2020,55(11):126-132. |
| 作者姓名： | 王欢 胡佳丽 张朝磊 李戬 苗红生 |
| 作者单位： | 1.北京科技大学材料科学与工程学院, 北京 100083; 2.青海大学机械工程学院, 青海 西宁 810016; 3.西宁特殊钢股份有限公司青海省特殊钢工程技术研究中心, 青海 西宁 810005 |
| 基金项目： | 青海省科技计划资助项目(2018-ZJ-747) |
| 摘 要： | 为了研究不同终轧温度下履带销轴用1E1158M钢奥氏体混晶情况,利用热模拟试验、显微组织定量分析以及截距法对不同状态下奥氏体晶粒以及本质晶粒的大小形貌进行研究,并提出了合理的终轧温度。结果表明,热轧态组织和正火态组织的粗化温度均为850 ℃,终轧温度对晶粒混晶程度有影响。终轧温度为850 ℃时,轧制终止时的奥氏体晶粒发生部分再结晶,混晶程度严重。随着终轧温度的升高,本质晶粒不均匀程度减小,建议终轧温度为1 000 ℃。 |
| 关 键 词： | 奥氏体晶粒 本质晶粒 混晶 终轧温度 1E1158M钢 |
| 收稿时间： | 2020-02-26 |
Mixed crystal of austenite grain size in track pins 1E1158M steel |
|
| WANG Huan,HU Jia-li,ZHANG Chao-lei,LI Jian,MIAO Hong-sheng.Mixed crystal of austenite grain size in track pins 1E1158M steel[J].Iron & Steel,2020,55(11):126-132. | |
| Authors: | WANG Huan HU Jia-li ZHANG Chao-lei LI Jian MIAO Hong-sheng |
| Affiliation: | 1. School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083, China;2. School of Mechanical Engineering, Qinghai University, Xining 810016, Qinghai, China;3. Qinghai Special Steel Engineering Technology Research Center, Xining Special Steel Co., Ltd., Xining 810005, Qinghai, China |
| Abstract: | The mixed crystal of austenite grain size in track pins 1E1158M steel was investigated at different finishing temperatures,then the grain size and it's microstructure were adopted to study the effect of different finishing temperatures by thermal simulation test,quantitative analysis of microstructure and intercept method. The results show that the abnormal grain growth temperature of hot-rolled and normal-fired microstructures is both 850 ℃,and the finishing rolling temperature has an effect on mixed crystal degree. When the finish rolling temperature is 850 ℃,the austenite grains are partially recrystallized at the end of rolling,and the degree of mixed crystals is serious. As the finishing temperature increases,the inhomogeneity of the intrinsic grain size decreases and the recommended finishing temperature is 1 000 ℃. |
| Keywords: | austenite grain size inherent grain size mixed crystal finishing temperature 1E1158M steel |
| 点击此处可从《钢铁》浏览原始摘要信息 | |
| 点击此处可从《钢铁》下载全文 | |