|
|||||
|
|
| 纳米压痕法对304不锈钢残余应力的研究 | |
| 引用本文： | 张龙,程光贵,丁建宁,凌智勇,张忠强.纳米压痕法对304不锈钢残余应力的研究[J].传感技术学报,2012,25(6):766-770. |
| 作者姓名： | 张龙 程光贵 丁建宁 凌智勇 张忠强 |
| 作者单位： | 1. 江苏大学机械工程学院,微纳米中心,江苏镇江212013 2. 江苏大学机械工程学院,微纳米中心,江苏镇江212013;阜宁经济开发区管理委员会,江苏阜宁224400 3. 江苏大学机械工程学院,微纳米中心,江苏镇江212013;常州市新能源重点实验室,江苏常州213164 |
| 基金项目： | 青年科学基金项目，江苏省高校自然科学研究项目，江苏大学高级专业人才科研启动基金项目 |
| 摘 要： | 利用纳米压痕法研究了304不锈钢的残余应力,采用Suresh理论模型恒定载荷时的公式计算残余应力,最大加载载荷依次为500μN、1 000μN、1 500μN、2 000μN、2500μN。结果表明,不锈钢硬度和弹性模量为定值,退火前后的硬度分别为5.3GPa和4.0 GPa,弹性模量分别为110 GPa和100 GPa。利用Ansys分析软件模拟了压痕过程,发现不锈钢在受压过程中有Sink-in现象发生。纳米压痕法测得了未退火不锈钢存在残余压应力,大小为381 MPa;用XRD测得了未退火不锈钢中有350 MPa±23 MPa的残余压应力,两种测量结果吻合良好,说明了纳米压痕法在残余应力测试时的准确性与可靠性。 |
| 关 键 词： | 残余应力 304不锈钢 纳米压痕法 |
Study of residual stress in the 304 stainless steel by nanoindentation method |
|
| ZHANG Long , CHENG Guanggui , DING Jianning , LING Zhiyong , ZHANG Zhongqiang.Study of residual stress in the 304 stainless steel by nanoindentation method[J].Journal of Transduction Technology,2012,25(6):766-770. | |
| Authors: | ZHANG Long CHENG Guanggui DING Jianning LING Zhiyong ZHANG Zhongqiang |
| Affiliation: | 1(1.Center of Micro/Nano Science & Technology,Jiangsu University,Zhenjiang Jiangsu 212013,China;2.Key Laboratory of New Energy Engineering, Changzhou Jiangsu 213164,China;3.Economic Development Zone Management Committee,Funing Jiangsu 224400,China) |
| Abstract: | The residual stress of the 304 stainless steel was investigated by nanoindentation method.The maximum loads were 500 μN,1 000 μN,1 500 μN,2 000 μN and 2 500 μN respectively.The Suresh theoretical model was used to calculate the residual stress.Results showed that the hardness and elastic modulus of un-annealed stainless steel are constant.The hardness of un-annealed and annealed stainless steel is 5.3 GPa and 4.0 GPa and the elastic modulus are 110 GPa and 100 GPa,respectively.Sink-in phenomenon was found during the indentation experiment based on the Ansys software.The compressive residual stress value in the stainless steel(381 MPa)was observed and calculated by the nanoindentation method,which is in good agreement with the result obtained by the XRD method(350 MPa±23 MPa).This agreement demonstrated the accuracy and reliability of using the nanoindentation method for residual stress study. |
| Keywords: | residual stress 304 stainless steel nanoindentation |
| 本文献已被 CNKI 万方数据 等数据库收录！ | |
| 点击此处可从《传感技术学报》浏览原始摘要信息 | |
| 点击此处可从《传感技术学报》下载全文 | |