| 热压烧结法制备铜-石墨复合材料及其摩擦学性能 |
| |
| 引用本文： | 苗迎春,张平,王亚东,朱劲波,杨猛,莫祥银,马立群.热压烧结法制备铜-石墨复合材料及其摩擦学性能[J].有色金属工程,2015,5(5). |
| |
| 作者姓名： | 苗迎春 张平 王亚东 朱劲波 杨猛 莫祥银 马立群 |
| |
| 作者单位： | 南京工业大学材料科学与工程学院 南京,山东临工工程机械有限公司 临沂,南京工业大学材料科学与工程学院 南京,南京工业大学材料科学与工程学院 南京,南京工业大学材料科学与工程学院 南京,南京师范大学 南京,南京工业大学材料科学与工程学院 南京 |
| |
| 基金项目： | 江苏省六大人才高峰项目（2012-XCL-034） |
| |
| 摘 要： | 采用真空热压烧结法制备铜-石墨复合材料,研究石墨质量分数分别为2%、5%和10%时,复合材料的密度、显微硬度、三点弯曲强度和摩擦磨损性能。结果表明,热压烧结法制备的复合材料组织较为致密,石墨分散均匀。随着石墨含量的增加,复合材料的硬度、强度下降,力学性能变差。复合材料的摩擦因数随着载荷的增加而增大,随着石墨含量的增加而降低,当石墨含量为10%时,复合材料的摩擦因数和质量磨损量最低,耐磨性能最好。
|
| 关 键 词： | 热压烧结 铜基复合材料 石墨 摩擦因数 |
| 收稿时间： | 2015/1/11 0:00:00 |
| 修稿时间： | 2015/1/19 0:00:00 |
Preparation and tribological properties of copper-graphite composite by hot press sintering |
| |
| miaoyingchun,zhangping,wangyadong,zhujinbo,yangmeng,moxiangyin and maliqun.Preparation and tribological properties of copper-graphite composite by hot press sintering[J].Nonferrous Metals Engineering,2015,5(5). |
| |
| Authors: | miaoyingchun zhangping wangyadong zhujinbo yangmeng moxiangyin and maliqun |
| |
| Affiliation: | College of Materials Science and Engineering Nanjing Tech University,Shandong Lingong Construction Machinery Co.Ltd,College of Materials Science and Engineering Nanjing Tech University,College of Materials Science and Engineering Nanjing Tech University,College of Materials Science and Engineering Nanjing Tech University,Nanjing Normal University,College of Materials Science and Engineering Nanjing Tech University |
| |
| Abstract: | Copper-graphite composite was prepared by hot press sintering in vacuum. The properties of the composites, such as density, micro-hardness, three point bending strength and wear performance with 2%, 5% and 10% mass fraction of graphite were studied. The results show that the structure of the composites prepared by hot press sintering is more dense, and the dispersion of graphite is uniform. The value of hardness and strength decreases with the increase of graphite, the mechanical property becomes bad. The friction coefficient of the composites increases with the increase of the load, and decreases with the increase of the content of graphite. When the content of graphite is 10%, the friction coefficient and wear rate is the lowest, the wear resistance is excellent. |
| |
| Keywords: | hot press sintering copper-based composite graphite friction coefficient |
| 本文献已被 CNKI 等数据库收录！ |
| 点击此处可从《有色金属工程》浏览原始摘要信息 |
|
点击此处可从《有色金属工程》下载全文 |
|
