| Q-I-Q-T工艺对60Si2CrVA钢断裂韧性的影响 |
| |
| 引用本文： | 任涛,梁益龙,刘国栋,王攀志.Q-I-Q-T工艺对60Si2CrVA钢断裂韧性的影响[J].兵器材料科学与工程,2012,35(3):9-11. |
| |
| 作者姓名： | 任涛 梁益龙 刘国栋 王攀志 |
| |
| 作者单位： | 贵州大学材料与冶金学院,贵州省材料结构与强度重点实验室,贵州贵阳550003;贵州大学材料与冶金学院,贵州省材料结构与强度重点实验室,贵州贵阳550003;贵州大学材料与冶金学院,贵州省材料结构与强度重点实验室,贵州贵阳550003;贵州大学材料与冶金学院,贵州省材料结构与强度重点实验室,贵州贵阳550003 |
| |
| 摘 要： | 研究60Si2CrVA弹簧钢经淬火-等温-淬火-回火(Q-I-Q-T)热处理后复相组织含量与断裂韧性间的关系。结果表明,在实验的等温温度范围内,随着等温温度的升高,残余奥氏体和贝氏体含量逐渐增大,60Si2CrVA钢强度降低,断裂韧性逐渐增加,在300℃等温时,断裂韧性达到最大值66.37 MPa.m1/2。稳定的残留奥氏体与过渡形态贝氏体量增加是提高断裂韧性的主要原因。
|
| 关 键 词： | 60Si2CrVA 淬火 回火 马氏体 贝氏体 残留奥氏体 |
Effects of Q-I-Q-T heat treatment technique on the fracture toughness of 60Si2CrVA steel |
| |
| REN Tao
,
LIANG Yilong
,
LIU Guodong
,
WANG Panzhi.Effects of Q-I-Q-T heat treatment technique on the fracture toughness of 60Si2CrVA steel[J].Ordnance Material Science and Engineering,2012,35(3):9-11. |
| |
| Authors: | REN Tao LIANG Yilong LIU Guodong WANG Panzhi |
| |
| Affiliation: | (College of Materials and Metallurgy,Guizhou University,Guizhou Key Laboratory for Mechanical Behavior and Microstructure of Materials,Guiyang 550003,China) |
| |
| Abstract: | The relationship between duplex structure and fracture toughness of 60Si2CrVA spring steel after quenching-isothermal-quenching-tempering process was studied.The results show that,in the experimental temperature range,with the increase of isothermal temperature,the content of retained austenite and bainite increases gradually,the strength decreases of 60Si2CrVA steel,and fracture toughness increases gradually.At the temperature of 300 ℃,fracture toughness reaches a maximum value of 66.37 MPa·m1/2.The increase of stable retained austenite and transitional form bainite is the main reason for the improvement of fracture toughness. |
| |
| Keywords: | 60Si2CrVA quenching tempering martensite bainite retained austenite |
| 本文献已被 CNKI 万方数据 等数据库收录！ |
|
