|
|||||
|
|
| Al_2O_3陶瓷与Q235钢的活性钎焊 | |
| 引用本文： | 王新阳,李炎,魏世忠,徐流杰,马向东.Al_2O_3陶瓷与Q235钢的活性钎焊[J].新技术新工艺,2010(5):85-89. |
| 作者姓名： | 王新阳 李炎 魏世忠 徐流杰 马向东 |
| 作者单位： | 1. 河南科技大学,材料科学与工程学院,河南,洛阳471003 2. 河南科技大学,材料科学与工程学院,河南,洛阳471003;河南科技大学,河南省耐磨材料工程技术研究中心,河南,洛阳471003 3. 河南科技大学,河南省耐磨材料工程技术研究中心,河南,洛阳471003 |
| 基金项目： | 河南省重点科技攻关项目 |
| 摘 要： | 采用二元Cu-Ti活性钎料连接氧化铝陶瓷与Q235钢,研究了反应温度、保温时间等钎焊工艺对接头组织与接头强度的影响,分析了接头的微观组织和界面产物。试验结果表明,界面分为3层结构,即液态钎料填充陶瓷微孔形成的反应层、合金钎料层、钢侧扩散层。XRD分析结果表明,界面产物为Cu3Ti3O、TiFe、TiFe2和Cu基固溶体。钎焊温度1050℃,保温时间30min时,接头抗剪强度达到99.3MPa。 |
| 关 键 词： | Cu—Ti钎料 Al2O3陶瓷 Q235钢 连接强度 微观组织 |
Active Brazing of Al2O3 Ceramics and Q235 Steel |
|
| WANG Xinyang,LI Yan,WEI Shizhong,XU Liujie,MA Xiangdong.Active Brazing of Al2O3 Ceramics and Q235 Steel[J].New Technology & New Process,2010(5):85-89. | |
| Authors: | WANG Xinyang LI Yan WEI Shizhong XU Liujie MA Xiangdong |
| Affiliation: | 1. School of Materials Science and Engineering, Henan University of Science and Technology, Luoyang 471003, China; 2. Henan Engineering Research Center for Wear of Materials, Henan University of Science and Technology, Luoyang 471003, China) |
| Abstract: | Al2O3 ceramics and Q235 steels were brazed by using binary Cu-Ti active filler metal. Effects of brazing parameters such as temperature, temperature holding time on joining strength, and interface microstructure and reaction offspring were investigated. The results show that an interface bonding zone consist of three layers, or reaction layer next to the ceramic, brazing alloy layer and diffusion layer to the steel side. The liquid braze alloy fills the micropores of ceramic and forms the reaction layer. Cu3 Ti3O, TiFe, TiFe2 and Cu-based solid solution are confirmed as the reaction products. Bonding temperature reached to 1050℃ temperature holding time reached to 30 min, and strength of the joint reached to 99.3 Mpa. |
| Keywords: | Cu-Ti filler metal Al2O3 ceramics Q235 steel Joining strength Microstructure |
| 本文献已被 CNKI 维普 万方数据 等数据库收录！ | |