| 织构拉刀的拉削负载特性建模与验证 |
| |
| 引用本文： | 倪敬,舒央,孟青新,吕俊杰,王书赢,胡春美. 织构拉刀的拉削负载特性建模与验证[J]. 中国机械工程, 2018, 29(11): 1329 |
| |
| 作者姓名： | 倪敬 舒央 孟青新 吕俊杰 王书赢 胡春美 |
| |
| 作者单位： | 1.杭州电子科技大学机械工程学院，杭州，3100182.浙江畅尔智能装备股份有限公司省级研发中心，缙云，321404 |
| |
| 基金项目： | 国家自然科学基金资助项目（51775153）National Natural Science Foundation of China （No. 51775153） |
| |
| 摘 要： | 针对传统圆孔拉削加工负载建模过程不够清晰，负载特性预测误差较大的问题，将拉刀刀齿上的槽定义成一种表面织构槽，综合考虑刀齿上的织构槽参数、拉削面积圆孔效应和拉削过程多齿接触周期特性，建立了较详细的织构拉刀拉削负载计算模型。基于经典刀齿切削负载理论，提出了具有织构槽拉刀的单齿拉削负载模型；考虑工件圆弧孔形状对拉削面积的影响，进一步优化单齿拉削负载模型；考虑由工件长度引起的多齿接触周期特性，得到一般性的织构拉刀拉削负载计算模型。仿真与实验结果表明，提出的模型能较好地预测实际拉削负载。同时也指出，在拉刀刀齿上开设织构槽可以降低拉削负载，但是开设的织构槽数量并非越多越好，而是存在一个最优值。
|
| 关 键 词： | 织构拉刀 负载建模 矩形织构槽 圆弧效应 |
Load Characteristic Modeling and Verification for Texture Broaches |
| |
| NI Jing,SHU Yang,MENG Qingxin,LYU Junjie,WANG Shuying,HU Chunmei. Load Characteristic Modeling and Verification for Texture Broaches[J]. China Mechanical Engineering, 2018, 29(11): 1329 |
| |
| Authors: | NI Jing SHU Yang MENG Qingxin LYU Junjie WANG Shuying HU Chunmei |
| |
| Affiliation: | 1.Mechanical Engineering School，Hangzhou Dianzi University，Hangzhou，3100182.Provincial-level R& D Center， Zhejiang CHR Intelligent Equipment Co.， Ltd.，Jinyun，Zhejiang， 321404 |
| |
| Abstract: | Aiming at the problems that traditional model of broaching load is not clearly and the modeling errors are quite big， the slots on the broach teeth were defined as surface texture grooves herein.A more detailed computational model of broaching load for texture broaches was provided with a consideration on texture groove parameters of cutter teeth， the circular holes of workpieces and tooth contacting cycle in broaching.First of all， based on the classical theory of cutting loads， a single tooth broaching load model for texture broaches was proposed.Then， the single tooth broaching load model was optimized with the influences of workpiece circular holes on the cutting areas.Finally， a universal computational model of broaching loads was obtained by adding tooth contacting cycle effects decided by workpiece lengths.The simulation and experimental results show that the proposed model may predict broaching load well.Moreover， it is proved that the texture groove may be used to reduce the broaching loads.And groove numbers aren't the more， the better.There is a optimal value for groove numbers. |
| |
| Keywords: | texture broach load modeling rectangular groove circle effect |
| 本文献已被 CNKI 等数据库收录！ |
| 点击此处可从《中国机械工程》浏览原始摘要信息 |
|
点击此处可从《中国机械工程》下载免费的PDF全文 |
