| AlN与Mo-Ni-Cu活性封接的微观结构和性能分析 |
| |
| 引用本文： | 张玲艳,秦明礼,曲选辉,陆艳杰,张小勇. AlN与Mo-Ni-Cu活性封接的微观结构和性能分析[J]. 无机材料学报, 2009, 24(3): 636-640. DOI: 10.3724/SP.J.1077.2009.00636 |
| |
| 作者姓名： | 张玲艳 秦明礼 曲选辉 陆艳杰 张小勇 |
| |
| 作者单位： | 1. 北京科技大学 粉末冶金研究所， 北京 100083； 2. 北京有色金属研究院， 北京 100088 |
| |
| 基金项目： | 国家重点基础研究发展规划(973计划) |
| |
| 摘 要： | AlN陶瓷是一种性能优良的电子封装材料，但不容易与金属直接连接在一起.实验采用98（Ag28Cu）2Ti活性焊料, 在真空条件下实现了AlN陶瓷与Mo Ni Cu合金的活性封接.利用EBSD、EDS、XRD方法研究了焊接区域以及剪切试样断裂表面的微观结构和相组成，测定了焊区的力学性能和气密性.研究结果显示：在AlN陶瓷界面上有TiN生成，说明陶瓷与焊料之间是一种化学键合，而在Mo Ni Cu合金的界面上有少量的Ni Ti金属间化合物存在.剪切后试样的断裂面上有TiN和AlN，说明断裂发生在靠近陶瓷的焊层区域.焊接试样性能优良：气密性达到1.0×10-11Pa·m3/s，平均抗弯强度σｂ=78.55MPa，剪切强度στ=189.58MPa.
|
| 关 键 词： | Ti-Ag-Cu活性焊料 活性封接 微观分析 封接性能 |
| 收稿时间： | 2008-08-19 |
| 修稿时间： | 2008-10-30 |
Microstructure and Mechanical Property Analysis of AlN Ceramic with Mo-Ni-Cu Alloy Active Brazed Joints |
| |
| ZHANG Ling-Yan,QIN Ming-Li,QU Xuan-Hui,LU Yan-Jie,ZHANG Xiao-Yong. Microstructure and Mechanical Property Analysis of AlN Ceramic with Mo-Ni-Cu Alloy Active Brazed Joints[J]. Journal of Inorganic Materials, 2009, 24(3): 636-640. DOI: 10.3724/SP.J.1077.2009.00636 |
| |
| Authors: | ZHANG Ling-Yan QIN Ming-Li QU Xuan-Hui LU Yan-Jie ZHANG Xiao-Yong |
| |
| Affiliation: | 1. Institute of Powder Metallurgy, University of Science and Technology Beijing, Beijing 100083, China; 2. General Research Institute for Nonferrous Metals, Beijing 100088, China |
| |
| Abstract: | AlN ceramic is a high performance electronic packaging material, but it is difficult to joint with metals directly. AlN ceramic and Mo-Ni-Cu alloy was brazed using 98（Ag28Cu）2Ti active filler alloy in vacuum. EBSD, EDS and XRD were used to study the microstructure and phases of bonding area and the surface of the sheared sample. The mechanical properties and hermeticity performance were measured. It is found that TiN exists in the interface of AlN ceramic, which indicate that there is a chemical bond between ceramic and filler metal, but there is a few of Ni-Ti intermetallics in the interface of Mo Ni-Cu alloy. TiN and AlN are found on the sheared fracture surface, which indicate that fracture occurrs from the bonding area near the AlN ceramic. The sample has good performance with gas leakage rate of 1.0×10-11Pa·m3/s, average bending strength of σｂ=78.55MPa and shear strength of στ=189.58MPa. |
| |
| Keywords: | Ti-Ag-Cu active filler alloy active brazing microstructure analysis mechanical properties |
| 本文献已被 维普 万方数据 等数据库收录！ |
| 点击此处可从《无机材料学报》浏览原始摘要信息 |
|
点击此处可从《无机材料学报》下载全文 |
