| 立方氮化硼用量及粒度对其同钛铝碳结合剂的反应程度的影响 |
| |
| 引用本文： | 梁宝岩,张旺玺,冯燕翔,穆云超. 立方氮化硼用量及粒度对其同钛铝碳结合剂的反应程度的影响[J]. 金刚石与磨料磨具工程, 2016, 36(5): 38-41. DOI: 10.13394/j.cnki.jgszz.2016.5.0007 |
| |
| 作者姓名： | 梁宝岩 张旺玺 冯燕翔 穆云超 |
| |
| 作者单位： | 1. 中原工学院 材料与化工学院, 郑州 451191;2. 金刚石技术国家地方联合工程实验室, 郑州 451191 |
| |
| 基金项目： | 河南省高校创新团队项目（15IRTSTHN004）；河南省省院科技合作项目（142106000193）；河南省教育厅自然科学研究计划项目资助（14A430007）；河南省科技开放合作项目（142106000051）；郑州市人才引育项目（141PRCYY514）；郑州市国际科技合作与交流项目（153PGJHZ209） |
| |
| 摘 要： | 为研究CBN用量对Ti3AlC2结合剂CBN复合材料的影响，使用不同质量配比的Ti3AlC2粉体和CBN粉体通过放电等离子体烧结的方式制备试样，并对比其物相组成和显微形貌。结果表明:当CBN质量分数为10%时，试样的主相为Ti3AlC2、CBN和TiC；当CBN质量分数为20%~40%时，生成了TiC、TiN、AlN、TiB2等物相。另一方面，当CBN质量分数为10%和20%时，CBN表面会形成厚约10 μm的过渡层；当CBN质量分数为30%和40%时，CBN与基体间没有过渡层。若选用粒度尺寸为10 μm的CBN（质量分数为10%）进行烧结，则复合材料中出现许多气孔，基体主相为TiC等轴晶粒且在CBN表面形成厚度1~2 μm的过渡层。CBN质量分数越大或粒度尺寸越小，其同Ti3AlC2的反应越充分、过渡层越薄。
|
| 关 键 词： | Ti3AlC2 立方氮化硼 复合材料 放电等离子体烧结 |
Fabrication and microstructure analysis of Ti3AlC2-CBN composites |
| |
| LIANG Baoyan,ZHANG Wangxi,FENG Yanxiang,MU Yunchao. Fabrication and microstructure analysis of Ti3AlC2-CBN composites[J]. Diamond & Abrasives Engineering, 2016, 36(5): 38-41. DOI: 10.13394/j.cnki.jgszz.2016.5.0007 |
| |
| Authors: | LIANG Baoyan ZHANG Wangxi FENG Yanxiang MU Yunchao |
| |
| Affiliation: | 1. Materials and Chemical Engineering School, Zhongyuan University of Technology, Zhengzhou 451191, China;2. National and Local Joint Laboratory of Engineering of Diamond Technology, Zhengzhou 451191, China |
| |
| Abstract: | Ti3AlC2-CBN composites are fabricated by spark plasma sintering using Ti3AlC2 and CBN powders as raw materials.Effect of CBN size and mass fraction on the phase composition and microstructure of the composites are studied.The results show that the main phases of the sample containing 10wt% CBN are Ti3AlC2,CBN and TiC.When CBN mass fraction is higher(20wt%-40wt%),TiC,TiN,AlN and TiB2 phases are formed.It is also shown that with 10wt% or 20wt% CBN,transition layer with a thickness of about 10 μm is formed on the surface of the CBN,while with 30 wt% or 40wt% CBN,there is no transition layer between CBN and the matrix.Many pores appear in the composite containing 10wt% CBN with a size of about 10 μm,whose main phase is TiC equiaxed grains with 1-2 μm transition layer on the surface of CBN.In conclusion,as CBN content increases or its mass fraction size decreases,CBN reacts more with Ti3AlC2,thus producing a thinner transition layer. |
| |
| Keywords: | |
| 本文献已被 CNKI 等数据库收录！ |
| 点击此处可从《金刚石与磨料磨具工程》浏览原始摘要信息 |
|
点击此处可从《金刚石与磨料磨具工程》下载免费的PDF全文 |
