| 基于试验设计与统计分析的双相钢激光焊工艺优化 |
| |
| 引用本文： | 赵大伟,康与云,易荣涛,梁东杰. 基于试验设计与统计分析的双相钢激光焊工艺优化[J]. 焊接学报, 2018, 39(1): 65-69. DOI: 10.12073/j.hjxb.2018390015 |
| |
| 作者姓名： | 赵大伟 康与云 易荣涛 梁东杰 |
| |
| 作者单位： | 临沂大学机械与车辆工程学院;中铁科工集团;广西计量检测研究院 |
| |
| 摘 要： | 为了优化激光焊接接头力学性能，利用试验设计方法对厚度为1.7 mm的DP600双相钢进行对接焊接试验，采用回归分析得到了激光焊接功率、焊接速度、离焦量、侧吹保护气体流量与接头抗拉强度之间的数学模型. 分析了焊接速度与侧吹气流量对焊缝抗拉强度的交互影响作用. 通过遗传算法优化该模型并得到了最优的焊接工艺参数组合，当焊接功率为1.7 kW，焊接速度为25 mm/s，侧吹气流量为2.4 m3/h，离焦量为-1 mm时焊缝的抗拉强度最大. 验证试验所测的焊缝抗拉强度值与模型预测值的相对误差在5%以内. 结果表明,文中研究可以有效的预测与优化厚度为1.7 mm的双相钢激光焊接质量.
|
| 关 键 词： | 双相钢 激光焊接 参数优化 试验设计 回归分析 |
| 收稿时间： | 2016-06-26 |
Research on process parameters optimization of laser welding for dual phase steel DP600 |
| |
| ZHAO Dawei,KANG Yuyun,YI Rongtao,LIANG Dongjie. Research on process parameters optimization of laser welding for dual phase steel DP600[J]. Transactions of The China Welding Institution, 2018, 39(1): 65-69. DOI: 10.12073/j.hjxb.2018390015 |
| |
| Authors: | ZHAO Dawei KANG Yuyun YI Rongtao LIANG Dongjie |
| |
| Abstract: | Experimental design was employed for 1.7 mm DP600 dual phase steel in order to optimize the laser welded joint mechanical property. The laser power, welding speed, focal point position and side-blowing shield gas flow were chosen as the process parameters and the mathematical model between the tensile strength of joint and the four process parameters were obtained by using regression analysis. The interaction effects of the welding speed and side-blowing shield gas on welding quality were explored. The optimal combination of welding process parameters was achieved using genetic algorithm and the largest tensile strength of welding joint was obtained as the welding power was 1.7 kW, welding speed was 25 mm/s, side-blowing shield gas flow was 2.4 m3/h, focal point position was -1 mm. The results of validation experiments showed that the model generally had a good effect and high precision, and its average relative error was within 5%, this study can effectively forecast and optimize the laser welding quality for the dual phase steel with the thickness of 1.7 mm. |
| |
| Keywords: | dual phase steel laser welding process parameters optimization experimental design regression analysis |
| 本文献已被 CNKI 等数据库收录！ |
| 点击此处可从《焊接学报》浏览原始摘要信息 |
|
点击此处可从《焊接学报》下载免费的PDF全文 |
|
