| 焊接工艺参数对钢/铌激光焊接头性能的影响 |
| |
| 引用本文： | 石铭霄,赵健,胡庆贤,陈书锦,周方明,王威林. 焊接工艺参数对钢/铌激光焊接头性能的影响[J]. 焊接学报, 2017, 38(4): 72-76. DOI: 10.12073/j.hjxb.20170417 |
| |
| 作者姓名： | 石铭霄 赵健 胡庆贤 陈书锦 周方明 王威林 |
| |
| 作者单位： | 1.江苏科技大学 材料科学与工程学院, 镇江 212003 |
| |
| 基金项目： | 国家自然科学基金资助项目，江苏省高校自然科学研究面上项目 |
| |
| 摘 要： | 采用正交试验法分析了焊接工艺参数对钢/铌激光焊接头抗拉强度的影响规律.结果表明，接头抗拉强度随着焊接速度的增大而降低；随着激光束从铌侧向钢侧偏移，接头强度逐渐升高；激光功率对接头强度的影响不大.在3个焊接工艺参数中，偏束距离对接头强度的影响最大，焊接速度次之，激光功率的影响最小.采用低焊接速度、向钢侧偏束的焊接方法可以提高焊接接头的抗拉强度.焊缝区主要包括铌侧的IMC区，焊缝中心的树枝晶区与钢侧的树枝晶区三个特征区.其组织由大量的γ奥氏体相与一定量的Fe2Nb相及少量的δ铁素体相组成.铁-铌金属间化合物的生成是降低接头强度的主要原因.
|
| 关 键 词： | 铌 304不锈钢 激光焊 焊接工艺参数 接头强度 |
| 收稿时间： | 2016-09-18 |
Influence of the parameters of welding procedure on mechanical properties of laser welded SS/Nb joint |
| |
| SHI Mingxiao,ZHAO Jian,HU Qingxian,CHEN Shujin,ZHOU Fangming and WANG Weilin. Influence of the parameters of welding procedure on mechanical properties of laser welded SS/Nb joint[J]. Transactions of The China Welding Institution, 2017, 38(4): 72-76. DOI: 10.12073/j.hjxb.20170417 |
| |
| Authors: | SHI Mingxiao ZHAO Jian HU Qingxian CHEN Shujin ZHOU Fangming WANG Weilin |
| |
| Affiliation: | 1.School of Materials Science and Engineering, Jiangsu University of Science and Technology, Zhenjiang 212003, China2.School of Materials Engineering, Shanghai University of Engineering Science, Shanghai 201620, China3.Engineering Technology Research Institute, PetroChina Southwest Oil & Gas Field Company, Chengdu 610017, China |
| |
| Abstract: | The influence law of the parameters of welding procedure on the tensile strength of laser welded stainless steel/niobium joint was studied by the orthogonal experiment. The results show that the tensile strength of joint decreased with the increase of welding speed, the strength of joint gradually rose with the laser beam moving from niobium to steel, and the influence of laser power on the strength of joint is very little. Among the three parameters of welding procedure, the influence of welding speed on the strength of joint is the largest, subsequently followed by the beam offset, and the influence of laser power on the strength of joint is minimum. The welding method of low welding speed and beam-offset to steel can improve the tensile strength of welded joint. The weld zone mainly consists of the IMC zone on the niobium side, the dendrite zone at the weld center and the dendrite zone on the steel side. The microstructure of joint mainly consists of plenty of γ austenite phase and a certain amount of Fe2Nb with little δ ferrite phase. The forming of Fe-Nb intermetallic compounds is the main reason for reducing the strength of joint. |
| |
| Keywords: | niobium 304 stainless steel laser welding parameters of welding procedure strength of joint |
| 本文献已被 CNKI 万方数据 等数据库收录！ |
| 点击此处可从《焊接学报》浏览原始摘要信息 |
|
点击此处可从《焊接学报》下载免费的PDF全文 |
|
