| 多孔钎焊砂轮的制备及SiC陶瓷磨削试验研究 |
| |
| 引用本文： | 刘伟,毛国安,严灿,李博鑫. 多孔钎焊砂轮的制备及SiC陶瓷磨削试验研究[J]. 中国机械工程, 2022, 33(15): 1787-1793. DOI: 10.3969/j.issn.1004-132X.2022.15.004 |
| |
| 作者姓名： | 刘伟 毛国安 严灿 李博鑫 |
| |
| 作者单位： | 1.湖南科技大学机电工程学院，湘潭，4112012.湖南科技大学难加工材料高效精密加工湖南省重点实验室，湘潭，411201 |
| |
| 基金项目： | 国家自然科学基金(51505144)；湖南省自然科学基金(2020JJ5178，2020JJ4024)；湖南省教育厅科学研究项目(20A202，18A182)；湖南省电磁装备设计与制造重点实验室开放基金(DC201901)；难加工材料高效精密加工湖南省重点实验室开放基金(E22002) |
| |
| 摘 要： | 基于模压成形和真空固相烧结工艺，选用Cu-10Sn结合剂、经氧化预处理的TiH2钎焊造孔剂、MBD8金刚石磨粒，制备出磨粒把持力大、孔隙分布均匀的多孔钎焊金刚石砂轮（PBDGW）。开展PBDGW与多层钎焊金刚石砂轮（MBDGW）的SiC陶瓷磨削对比试验，从磨削力、工件表面粗糙度和表面/亚表面形貌等方面分析砂轮的磨削性能。试验结果表明：与MBDGW相比，PBDGW磨削SiC陶瓷的切向力下降了8.4%～23.6%、法向力下降了10.2%～38.6%，磨削加工表面粗糙度平均降幅为10.4%；工件表面完整性较好，表面/亚表面的脆性断裂、微观裂纹等缺陷较少。
|
| 关 键 词： | 多孔 钎焊砂轮 TiH2 SiC陶瓷 磨削性能 |
Preparation of Porous Brazed Grinding Wheels and Experimental Research of SiC Ceramic Grinding |
| |
| LIU Wei,MAO Guoan,YAN Can,LI Boxin. Preparation of Porous Brazed Grinding Wheels and Experimental Research of SiC Ceramic Grinding[J]. China Mechanical Engineering, 2022, 33(15): 1787-1793. DOI: 10.3969/j.issn.1004-132X.2022.15.004 |
| |
| Authors: | LIU Wei MAO Guoan YAN Can LI Boxin |
| |
| Affiliation: | 1.School of Mechanical Engineering，Hunan University of Science and Technology，Xiangtan，Hunan，4112012.Hunan Provincial Key Laboratory of High Efficiency and Precision Machining of Difficult-to-cut Material，Hunan University of Science and Technology，Xiangtan，Hunan，411201 |
| |
| Abstract: | Based on the molding and vacuum solid-phase sintering processes，a porous brazed diamond grinding wheel（PBDGW）with high bonding strength and uniform pore distribution was prepared by using Cu-10Sn binder，oxidation pretreated TiH2 brazed pore-forming agent and MBD8 diamond abrasive particles. The SiC ceramic grinding experiments of PBDGW and multilayer brazed diamond grinding wheel（MBDGW） were carried out for comparison，then the grinding performances of grinding wheel were analyzed from grinding force，workpiece surface roughness and surface/sub-surface morphology. The experimental results show that the tangential force in SiC ceramics grinding with PBDGW decreases by 8.4%～23.6%，the normal force decreases by 10.2%～38.6%，and the average reduction of surface roughness is as 10.4%. The workpiece surface has better integrity，and the surface/sub-surface brittle fracture，microscopic crack and other defects are less. |
| |
| Keywords: | porous brazed grinding wheel TiH2 SiC ceramics grinding performance |
|
| 点击此处可从《中国机械工程》浏览原始摘要信息 |
|
点击此处可从《中国机械工程》下载免费的PDF全文 |
